4 layers155 × 75 mm
GTI V5
fotherja/Grid_Tie_Inverter_V5
Please refer to my site ( www.jamesfotherby.com ) where this project is being documented in detail
165 parts47MIT
4 layers58.5 × 87 mm
LB MBoard
irozalski/LiquorBot- Size
- 58.5 × 87 mm
- Copper layers
- 4
- Thickness
- 1.58 mm
- Parts
- 46
- Nets
- 61
- Pads
- 261
- Tracks, vias
- 351, 180
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 22 Mar 2023
- Updated
- 4 Nov 2024
Overview
LB MBoard is an open-source printed circuit board by irozalski, from the irozalski/LiquorBot repository on GitHub. It is a 4-layer board of 58.5 × 87 mm with 46 parts on 61 nets, routed with 351 tracks and 180 vias.
It is built around the ESP32-S3-WROOM-1-N16R2, AP2210K-5.0TRG1 and LM1117DT-3.3, with the SRV05-4, B5B-XH-AM and WS2812B among its other parts. Its parts include 12 capacitors, 9 resistors, 6 ICs, 5 connectors and 3 diodes. It belongs with the ESP32 boards of this library.
Main components
6
ESP32-S3-WROOM-1-N16R2
SMD,25.5x18mm-103.5dBm -40℃~+85℃ 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 On-board PCB Antenna UART、SDIO、SPI、I2C、GPIO、PWM、ADC、I2S、JTAG、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi Modules
AP2210K-5.0TRG1
SOT-23-5-40℃~+125℃@(Tj) 1 13.2V 150uA 300mA 400mV@(300mA) 5V 75dB@(100Hz) Fixed Over Current Protection、Over Temperature Protection、Reverse connection protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
LM1117DT-3.3
TO-2520℃~+125℃@(Tj) 1 1.2V@(800mA) 15V 3.3V 5mA 75dB@(120Hz) 800mA Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive TO-252 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
SRV05-4
SOT-23-6L-55℃~+150℃ 15V 1pF 4A 5V 5uA 6V 80W ESD Four channels IEC 61000-4-2、IEC 61000-4-5 Unidirectional SOT-23-6L ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)
B5B-XH-AM
插件,P=2.5mm-25℃~+85℃ 1 14.9mm 1x5P 2.5mm 250V 3A 5 5.75mm 5P 7mm Brass K Pin、With post PA66 Through Hole Tin UL94V-0 White XH 插件,P=2.5mm Wire To Board Connector ROHSJSTWire To Board Connector
WS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
README.md🤖 LiquorBot
Automatic liquor dispensing machine used for pouring several-layer shots.
The project uses a stepper motor, liquid pumps, Hall sensor, optocouplers and LEDs controlled by the Esp32 microcontroller.
Most of the case parts were printed on a 3D printer.
Electronic schematic
PCB 3D visualisation
Render of project
Parts
46| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C2, C3, C4, C9 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric | R3, R4, R5 |
| 3 | 10uF | Capacitor_SMD:C_0805_2012Metric | C1, C5, C7 |
| 3 | 220 | Resistor_SMD:R_0805_2012Metric | R8, R10, R14 |
| 3 | Fiducial | Fiducial:Fiducial_1mm_Mask2mm | FM1, FM2, FM3 |
| 2 | 5.1k | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | LED | LED_SMD:LED_0805_2012Metric | D2, D3 |
| 2 | SW_MEC_5E | switch:SW_PTS_647_SN50_SMTR2_LFS | BOOT, RESET |
| 1 | 100u | Polar_Cap35:CAP_EEE1VA101XP | C10 |
| 1 | 100uF | Capacitor_SMD:C_0805_2012Metric | C6 |
| 1 | 1uF | Capacitor_SMD:C_0805_2012Metric | C12 |
| 1 | 2.2uF | Capacitor_SMD:C_0805_2012Metric | C11 |
| 1 | 200 | Resistor_SMD:R_0805_2012Metric | R7 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric | C8 |
| 1 | A4988_STEPPER_MOTOR_DRIVER | A4988:MODULE_A4988_STEPPER_MOTOR_DRIVER_CARRIER | U6 |
| 1 | AP2210K-5.0TRG1 | AP2210:SOT-23-5_RAW | U2 |
| 1 | AZ1084-5.0 | AZ108:DPAK457P1010X238-3N | U3 |
| 1 | B5B-XH-A | jst:JST_B5B-XH-A | J5 |
| 1 | ESP32-S3-WROOM-1-N16R2 | esp2:XCVR_ESP32-S3-WROOM-1U-N16 | U1 |
| 1 | LM1117DT-3.3 | Package_TO_SOT_SMD:TO-252-3_TabPin2 | U7 |
| 1 | LOGO | demo.preety:logodemo | G*** |
| 1 | SRV05-4 | Package_TO_SOT_SMD:SOT-23-6 | U5 |
| 1 | Screw_Terminal_01x03 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-3_1x03_P5.00mm_Horizontal | J3 |
| 1 | Screw_Terminal_01x10 | molex10:393570010 | J4 |
| 1 | Screw_Terminal_01x12 | molex12:393570012 | J1 |
| 1 | Screw_Terminal_01x15 | molex15:393570015 | J9 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C:GCT_USB4085-GF-A_REVB | J_USB1 |
| 1 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1 |
Similar boards
- 2 layers80 × 128.5 mm
RP2040-VCO
BleepSound/rp2040-chord-vco
Latest documentation available at https://bleepsound.github.io/modules/ VCO clone, originally made by HAGIWO (link in japanese)
58 parts9CC-BY-SA-4.0 - 2 layers133 × 97.8 mm
- 2 layers48.5 × 76.8 mm
MCU ATMEGA328p minimum
m0in92/common_pcb_circuits
Kicad schematics and PCB for common electric circuits
21 parts1 - 2 layers
- 2 layers71.3 × 94.1 mm
- 2 layers396.3 × 336.1 mm
Chessconnect
K-0hm/Chessboard
Code for a chessboard with light and capacitance Touch Sensors.
260 partsGPL-3.0 - 2 layers58.1 × 41.8 mm
Esp32-led matrix
n2048-creative-technology/esp32-led-matrix
double sided 8x8 addressable led matrix with integrated esp32-c3 module
147 parts
Questions
How big is the LB MBoard PCB?
It measures 58.5 × 87 mm and has 4 copper layers, 1.58 mm thick.
What parts does the LB MBoard use?
46 parts, built around the ESP32-S3-WROOM-1-N16R2, AP2210K-5.0TRG1, LM1117DT-3.3 and SRV05-4. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the LB MBoard KiCad files?
From the irozalski/LiquorBot repository on GitHub, at the commit this page was made from: the board is KiCad files/LB_MBoard.kicad_pcb and its schematic KiCad files/LB_MBoard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the LB MBoard design in my own project?
Its repository states no licence, so its author keeps all rights: ask irozalski before reusing the design.