Skip to the content
2 layers76.2 × 78.1 mmWasserhahn, the printed circuit board in 3D

MQTT controlled Motor Bulb Valve ESP8266 Arduino

Size
76.2 × 78.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
21
Nets
24
Pads
72
Tracks, vias
207, 11
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
26 Apr 2020
Updated
12 Mar 2023

Overview

Wasserhahn is an open-source printed circuit board by ingeninge, from the ingeninge/Wasserhahn repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 76.2 × 78.1 mm with 21 parts on 24 nets, routed with 207 tracks and 11 vias.

It is built around the ESP-WROOM-02. Its parts include 9 resistors, 6 connectors, 4 capacitors and 1 IC.

Main components

1

README

README.md

Wasserhahn

ATTENTION! This repository is only for testing! No production, and never will be.

MQTT controlled Motor Bulb Valve ESP8266 Arduino Image of the motor driver Manufactor is END. Here is a link to the Datasheet: https://shop.end.de/armaturen/antriebe-und-zubehoer/elektrische-antriebe/ne034100-elektrischer-schwenkantrieb-30nm-230v-ac

Since my water tap in the garden was leaking and the repair would have included ripping down the building bricks, I asked a friend to build in a ball valve. On this I could mount a motor to open and close the garden water tap. To control the motor I use a ESP8266-12 (WROOM-02) and two relays. The ESP uses 2 Inputs and 2 Outputs. The schematic can be found in the folder images. The Inputs are from the auxiliary isolated contacts from the motor. The contacts are closed ONLY at the end position of each turn.br>If both are open the valve is in between open and close. The Outputs are controlling two relays. One for opening and one for closing the valve. The outputs are held active for 90 seconds.
MQTT- protocol is used to control the garden water tap remotely. First idea was to let it work with an Arduino Sketch, witch you can find in the sources. But then I figured out how to set up Tasmota to work with this Board and Motor. The workaround is: Tasmota [https://github.com/arendst/Tasmota] (I use Version 7.1) controls 2 relays - one for Opening and one for Closing the tap. The downside is, you will have to use two buttons or configure node-red with a function to control the state and switch between the states.
For Programming see https://www.forward.com.au/pfod/ESP8266/GPIOpins/index.html GPIO0 and RST are on Jumper J5. GPIO2 is permanently pulled up via R8. Todo: Remove copper under the antenna! Enable access to GPIO15 for programming mode or pull low permanent. update mill and drill files, mill, solder and test the layout. Release to public

The settings for Tasmota can be found in the Wiki https://github.com/ingeninge/Wasserhahn/wiki

BTW: I can control the bulb valve with a remote control in the garden, so I don't have to pull out my mobile to open the tap. Remote control for Wasserhahn

Parts

21
QtyValueFootprintReferences
710KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR3, R4, R5, R6, R7, R8, R9
3100nFCapacitor_THT:CP_Radial_D4.0mm_P2.00mmC1, C2, C3
2220Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R2
110µFCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC4
1Ball_Valve_ContactsTerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-4-5.0-H_1x04_P5.00mm_HorizontalJ2
1ESP-WROOM-02RF_Module:ESP-WROOM-02U1
1HLK-PM01/TSP-03Converter_ACDC:Converter_ACDC_HiLink_HLK-PMxxPS1
1IsolateConnector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_VerticalJ6
1MainsTerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_HorizontalJ1
1PRGM_ADAPTERConnector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalJ4
1RST/PRGMConnector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_VerticalJ5
1ToRelaisConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ3

Similar boards

  • 2 layers13.7 × 21.4 mmZ2m partner, the printed circuit board in 3D

    Z2m partner

    smarthomefans/z2m_partner

    Hardware module for iobroker.zigbee

    52 parts186
  • 2 layers41.3 × 87.1 mmUnified smd pcb, the printed circuit board in 3D

    Unified smd pcb

    Al-Nafuur/United-Carts-of-Atari

    Firmware for PlusCart and UnoCart

    22 parts45GPL-3.0
  • 4 layers77.6 × 57.3 mmWifistepper, the printed circuit board in 3D

    Wifistepper

    goodrobotics/wifistepper

    Wi-Fi Stepper project repo

    92 parts29
  • 2 layers72.5 × 17 mmLight timer, the printed circuit board in 3D

    Light timer

    mulcmu/esphome-usb-grow-lights

    Custom PCB and esphome configuration for usb powered grow lights.

    41 parts21MIT
  • 2 layers92 × 73.1 mmOpen squib esp wroom v2, the printed circuit board in 3D

    Open squib esp wroom v2

    chromalock/OpenSquib

    Open-Sourced implementation of a PCB-Based Squib

    37 parts17CC0-1.0
  • 4 layers25.5 × 22.4 mmWi se rewirable, the printed circuit board in 3D

    Wi se rewirable

    depau/wi-se-hw

    Cheap and tiny ESP8266 boards for Wi-Se to access your SBC or router serial port remotely

    51 parts11
  • 2 layers29 × 36 mmTheta remote release, the printed circuit board in 3D

    Theta remote release

    shrhdk/theta-remote-release

    simple remote release device for THETA S.

    22 parts3
  • 2 layers85 × 56 mmWifi-30A relay, the printed circuit board in 3D

    Wifi-30A relay

    flaviut/30a-water-heater-controller

    Makes any resistive water heater 30A or less WiFi controllable

    42 parts2CERN-OHL-S-2.0

Questions

How big is the Wasserhahn PCB?

It measures 76.2 × 78.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Wasserhahn use?

21 parts, built around the ESP-WROOM-02. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Wasserhahn KiCad files?

From the ingeninge/Wasserhahn repository on GitHub, at the commit this page was made from: the board is Wasserhahn.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Wasserhahn design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).