

Wasserhahn
MQTT controlled Motor Bulb Valve ESP8266 Arduino
- Size
- 76.2 × 78.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 21
- Nets
- 24
- Pads
- 72
- Tracks, vias
- 207, 11
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 26 Apr 2020
- Updated
- 12 Mar 2023
Overview
Wasserhahn is an open-source printed circuit board by ingeninge, from the ingeninge/Wasserhahn repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 76.2 × 78.1 mm with 21 parts on 24 nets, routed with 207 tracks and 11 vias.
It is built around the ESP-WROOM-02. Its parts include 9 resistors, 6 connectors, 4 capacitors and 1 IC.
Main components
1README
README.mdWasserhahn
ATTENTION! This repository is only for testing! No production, and never will be.
MQTT controlled Motor Bulb Valve ESP8266 Arduino
Manufactor is END. Here is a link to the Datasheet: https://shop.end.de/armaturen/antriebe-und-zubehoer/elektrische-antriebe/ne034100-elektrischer-schwenkantrieb-30nm-230v-ac
Since my water tap in the garden was leaking and the repair would have included ripping down the building bricks, I asked a friend to build in a ball valve.
On this I could mount a motor to open and close the garden water tap.
To control the motor I use a ESP8266-12 (WROOM-02) and two relays. The ESP uses 2 Inputs and 2 Outputs.
The schematic can be found in the folder images.
The Inputs are from the auxiliary isolated contacts from the motor. The contacts are closed ONLY at the end position of each turn.br>If both are open the valve is in between open and close.
The Outputs are controlling two relays. One for opening and one for closing the valve. The outputs are held active for 90 seconds.
MQTT- protocol is used to control the garden water tap remotely.
First idea was to let it work with an Arduino Sketch, witch you can find in the sources. But then I figured out how to set up Tasmota to work with this Board and Motor. The workaround is: Tasmota [https://github.com/arendst/Tasmota] (I use Version 7.1) controls 2 relays - one for Opening and one for Closing the tap. The downside is, you will have to use two buttons or configure node-red with a function to control the state and switch between the states.
For Programming see https://www.forward.com.au/pfod/ESP8266/GPIOpins/index.html GPIO0 and RST are on Jumper J5. GPIO2 is permanently pulled up via R8.
Todo: Remove copper under the antenna! Enable access to GPIO15 for programming mode or pull low permanent. update mill and drill files, mill, solder and test the layout. Release to public
The settings for Tasmota can be found in the Wiki https://github.com/ingeninge/Wasserhahn/wiki
BTW: I can control the bulb valve with a remote control in the garden, so I don't have to pull out my mobile to open the tap. Remote control for Wasserhahn
Parts
21| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3, R4, R5, R6, R7, R8, R9 |
| 3 | 100nF | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C1, C2, C3 |
| 2 | 220 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2 |
| 1 | 10µF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C4 |
| 1 | Ball_Valve_Contacts | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-4-5.0-H_1x04_P5.00mm_Horizontal | J2 |
| 1 | ESP-WROOM-02 | RF_Module:ESP-WROOM-02 | U1 |
| 1 | HLK-PM01/TSP-03 | Converter_ACDC:Converter_ACDC_HiLink_HLK-PMxx | PS1 |
| 1 | Isolate | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J6 |
| 1 | Mains | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J1 |
| 1 | PRGM_ADAPTER | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J4 |
| 1 | RST/PRGM | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J5 |
| 1 | ToRelais | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
Similar boards
- 2 layers13.7 × 21.4 mm

- 2 layers41.3 × 87.1 mm

- 4 layers77.6 × 57.3 mm

- 2 layers72.5 × 17 mm

Light timer
mulcmu/esphome-usb-grow-lights
Custom PCB and esphome configuration for usb powered grow lights.
41 parts21MIT - 2 layers92 × 73.1 mm

Open squib esp wroom v2
chromalock/OpenSquib
Open-Sourced implementation of a PCB-Based Squib
37 parts17CC0-1.0 - 4 layers25.5 × 22.4 mm

Wi se rewirable
depau/wi-se-hw
Cheap and tiny ESP8266 boards for Wi-Se to access your SBC or router serial port remotely
51 parts11 - 2 layers29 × 36 mm

- 2 layers85 × 56 mm

Wifi-30A relay
flaviut/30a-water-heater-controller
Makes any resistive water heater 30A or less WiFi controllable
42 parts2CERN-OHL-S-2.0
Questions
How big is the Wasserhahn PCB?
It measures 76.2 × 78.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Wasserhahn use?
21 parts, built around the ESP-WROOM-02. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Wasserhahn KiCad files?
From the ingeninge/Wasserhahn repository on GitHub, at the commit this page was made from: the board is Wasserhahn.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Wasserhahn design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).