2 layers158 × 34 mm
2 layers
TaggerMainboard
Infinitag/Hardware6Files for the INFINITAG hardware
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 67
- Nets
- 67
- Pads
- 348
- Tracks, vias
- 1,037, 149
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 13 Nov 2016
- Updated
- 7 Jun 2019
Overview
TaggerMainboard is an open-source printed circuit board by Infinitag, from the Infinitag/Hardware repository on GitHub. It is a 2-layer board with 67 parts on 67 nets, routed with 1,037 tracks and 149 vias.
It is built around the LMV358, FT232RL and LM2596S-5.0, with the AMS1117-3.3, IRLML2502 and CD1206-S01575 among its other parts. Its parts include 14 capacitors, 11 resistors, 6 ICs, 3 connectors and 2 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
8
LMV358
SOP-8-40℃~+125℃ 10pA 10pA 1MHz 2 2.5V~5.5V 20mA 20nV/√Hz@10kHz 2uV/℃ 40uA 5mV 600V/ms 65dB EMI filtering/RF suppression Rail-to-Rail Input, Rail-to-Rail Output SOP-8 Operational Amplifier ROHSTECH PUBLICOperational Amplifier
FT232RL
SSOP-28-208mil-40℃~+85℃ 3.3V~5.25V、4V~5.25V USB 2.0 USB to UART SSOP-28-208mil USB Converters ROHSFTDIUSB Converters
LM2596S-5.0
TO-263-5-40℃~+125℃@(TJ) 1 150kHz 3A 4.5V~40V 5V 5mA Buck Buck Built-in Fixed No TO-263-5 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
IRLML2502
SOT-23-40℃~+150℃ 1 N-channel 1.25W 20V 4.2A 50mΩ@2.5V 600mV 66pF 740pF 8nC@10V SOT-23 MOSFETs ROHSGuangdong HottechMOSFETs
CD1206-S01575
1206-55℃~+125℃ 150mA 1V@50mA 2.5uA@75V 400mW 4A 4ns 75V Standalone 1206 Switching Diodes ROHSBournsSwitching Diodes
CSTCE16M0V53-R0
SMD3213-3P-20℃~+80℃ 15pF 16MHz 40Ω SMD3213-3P Ceramic Resonators ROHSMurataCeramic ResonatorsFDN304P
SOT-23-55℃~+150℃ 1 P-Channel 1.312nF 1.5V 100mΩ@1.8V 106pF 2.4A 20V 20nC@4.5V 240pF 500mW P-Channel SOT-23 MOSFETs ROHSonsemiMOSFETs
README
README.mdINFINITAG Hardware
All hardware files for the INFINITAG laser tag system
Credits
Website: http://www.infinitag.io
License
All files are published under Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0) License https://creativecommons.org/licenses/by-nc-sa/4.0/
Parts
67| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100nF | Capacitor_SMD:C_0805_2012Metric | C1, C2, C3, C4, C6, C12, C13 |
| 6 | 10K | Resistor_SMD:R_0805_2012Metric | R2, R3, R4, R6, R7, R9 |
| 4 | 220uF/16V | Capacitor_SMD:CP_Elec_6.3x5.8 | C5, C8, C10, C15 |
| 3 | 1K | Resistor_SMD:R_0805_2012Metric | R8, R10, R11 |
| 2 | Array 10K | Resistor_SMD:R_Array_Convex_4x0603 | RN1, RN2 |
| 2 | JSP_PH_Sensor | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | Sensor 1, Sensor 2 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C9 |
| 1 | 1M | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 22pF | Capacitor_SMD:C_0805_2012Metric | C7 |
| 1 | 330uH | Inductor_SMD:L_Wuerth_HCI-1350 | L1 |
| 1 | 50 Ohm | Resistor_SMD:R_0805_2012Metric | R5 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | Array 470 | Resistor_SMD:R_Array_Convex_4x0603 | RN3 |
| 1 | Bildmarke_6x6mm | Infinitag:Bildmarke_6x6mm | G*** |
| 1 | CD1206-S01575 | Diode_SMD:D_1206_3216Metric | D5 |
| 1 | CSTCE16M0V53-R0 | Crystal:Resonator_SMD_muRata_CSTxExxV-3Pin_3.0x1.1mm | Y1 |
| 1 | C_Small | Capacitor_SMD:C_0805_2012Metric | C11 |
| 1 | DFPlayer | Infinitag:DFPlayer | J3 |
| 1 | FDN304P | FDN304P:SSOT-3 | Q1 |
| 1 | FT232RL | Package_SO:SSOP-28_5.3x10.2mm_P0.65mm | U6 |
| 1 | ICSP | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J6 |
| 1 | IRLML2502 | IRLML2502TRPBF:SOT23 | U2 |
| 1 | Infinitag_Shield | Infinitag:Infinitag_Shield | Extension Shield |
| 1 | JST_PH_Display | Connector_JST:JST_PH_B5B-PH-K_1x05_P2.00mm_Vertical | Display |
| 1 | JST_PH_Info | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | Info |
| 1 | JST_PH_IrLED | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | IR Module |
| 1 | JST_PH_Keypad | Connector_JST:JST_PH_B8B-PH-K_1x08_P2.00mm_Vertical | Keypad |
| 1 | JST_PH_LEDbar_left | Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | LED left |
| 1 | JST_PH_LEDbar_right | Connector_JST:JST_PH_B3B-PH-K_1x03_P2.00mm_Vertical | LED right |
| 1 | JST_PH_Reload | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | Reload |
| 1 | JST_PH_Speaker | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | Speaker |
| 1 | JST_PH_Special | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | Special |
| 1 | JST_PH_Trigger | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | Trigger |
| 1 | LED_RX_red | LED_SMD:LED_1206_3216Metric | RX |
| 1 | LED_TX_red | LED_SMD:LED_1206_3216Metric | TX |
| 1 | LED_green | LED_SMD:LED_1206_3216Metric | PWR |
| 1 | LM2596S-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U3 |
| 1 | LMV358 | LMV358AM8X:SOIC127P620X172-8N | U4 |
| 1 | MCU-ATMEGA2560-16AU(TQFP100) | MCU-ATMEGA2560-16AU_TQFP100_:TQFP100-0.5-14X14MM | U1 |
| 1 | Poly 500mA | Fuse:Fuse_1812_4532Metric | F1 |
| 1 | S534 | Diode_SMD:D_SMA | D4 |
| 1 | SW_Reset | Button_Switch_SMD:SW_SPST_FSMSM | Reset |
| 1 | USB_OTG | Infinitag:Micro USB Jack | J5 |
| 1 | VIN | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | V-In |
| 1 | WiFi Connector | Infinitag:Infinitag_ESP_Shield | WiFi Shield |
The 63 most common of 67 parts.
Questions
What parts does the TaggerMainboard use?
67 parts, built around the LMV358, FT232RL, LM2596S-5.0 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the TaggerMainboard KiCad files?
From the Infinitag/Hardware repository on GitHub, at the commit this page was made from: the board is PCB/TaggerMainboard/TaggerMainboard.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the TaggerMainboard design in my own project?
Its repository states no licence, so its author keeps all rights: ask Infinitag before reusing the design.
More from Infinitag/Hardware
3- 2 layers38 × 59 mm
- 2 layers22 × 22 mm
Similar boards
- 2 layers97 × 75.5 mm
Arduino Uno R3
SuganyaBaskaran/kicad-projects
Portfolio, learning and practice attempts using KiCAD.
56 parts - 2 layers68.6 × 53.3 mm
INK-128DA28
TheEccentricGenius/INK4u_Board
An UNO form factor board with a AVR128DA28 processor.
59 parts5CERN-OHL-W-2.0 - 2 layers101.6 × 53.3 mm
- 2 layers101.6 × 53.3 mm
Arduino mega 2560 rev3e
javachaos/arduino_simulator
arduinosimulator is a standalone AVR simulation and board-tooling workspace.
72 partsGPL-3.0 - 2 layers101.6 × 53.3 mm
- 2 layers100 × 54 mm
- 2 layers101.6 × 53.3 mm
- 6 layers150 × 118 mm
Qssc
VABISMO/QSSC
Quantum Solid State Chip - NV DIAMOND . Spin Defect Simulator and hardware controller with Qiskit backend (WIP)
135 parts1