Skip to the content
2 layers50.2 × 34.9 mmMoreVO Core, the printed circuit board in 3D

MoreVO Core

ImoogDi/2MoreVO1

Eurorack dual VCO using the public AS3340/CEM3340

Size
50.2 × 34.9 mm
Copper layers
2
Thickness
1.6 mm
Parts
77
Nets
59
Pads
197
Tracks, vias
358, 43
Pours
2
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
14 Jul 2024
Updated
10 Aug 2024

Overview

MoreVO Core is an open-source printed circuit board by ImoogDi, from the ImoogDi/2MoreVO repository on GitHub. It is a 2-layer board of 50.2 × 34.9 mm with 77 parts on 59 nets, routed with 358 tracks and 43 vias.

It is built around the MMBT3906. Its parts include 42 resistors, 14 capacitors, 3 ICs, 3 diodes and 2 connectors. It belongs with the audio and music boards of this library.

Main components

1

README

README.md

2MoreVO

Eurorack Dual VCO using the public CEM3340/AS3340 chip.

Table of Contents

Introduction [blocked]

This eurorack-modul is designed for modular-synthesizers as dual Voltage Controlled Oscillator.
The oszillators are build around two IC's: AS3340, a clone of that wellknown CEM3340.
Another benifit is the three cannel VCA: AS3363 included to control the modulation-level, waveform output of VCO1 and oscillator-signal fading between VCO1- and VCO2-outputs.

The '2MoreVO'-PCB's are:

  • one main backplane ('Backplane'), holding all switches, pots, jacks and voltage-references.
  • two VCO-PCB's stacked on the 'Backplane'.
  • one another backplane-PCB ('Backplane_B') hodling the 'three cannel VCA', operational-amp's and the eurorack-connection stacked on the 'Backplane'.

All parts are common available and DIY-friendly designed, most parts are SMD on the VCO-PCB's.
(Details see attached pictures)

  • Modul Frontpanel

Modul: 2MoreVO Front


- Modul Backpanel

Modul: 2MoreVO Backside


- Modul function-blocks

Modul: 2MoreVO function blocks



There are twelve 3.5mm jacks available for patching audio- and CV-signals.
Jack-NameFunctionCommentDetail
1V/Oct CV1CV-input for VCO1 pitch controlfixed 1Volt/Octave scalingThis input is normalised with the eurobus Control-Voltage and connected with the '1V/Oct CV2' input.
Patch-cabel plugged in breaks the default connection to eurobus CV but the connection to '1V/Oct CV2' is still available.
Fade CVCV-input for fading oscillator-signalsThe Fading between Osc1- and Osc2-signals on 'Osc-Mix Out' is controlled with this CVCV level adjustable between 0 ... max. with 'Fade CV'-pot.
works together with 'Osc-Fade'-pot.
Bipolar signal input.
Wave1 CVCV-input for VCO1 wave-controlThe waveform on 'Osc1 Out' is controlled with this CVCV Level adjustable between 0 ... max. with 'Wave1 CV'-pot.
Bipolar signal input.
Mod.Level CVCV-input for modulation level controlControl of modulation level on 'Mod Out'Modulation Level adjustable between 0 ... max. with 'Mod.Level CV'-pot.
Bipolar signal input.
Mod. InModulation signal inputinput for external signals controlling FM(Lin/Log) and PWM on Osc1 and Osc2This input is normalised with the sinusoidal-signal from Osc2 if no signal is plugged in.
Bipolar signal input.
1V/Oct CV2CV-input for VCO2 pitch controlfixed 1Volt/Octave scalingThis input is normalised with the '1V/Oct CV1' input.
Patch-cabel plugged in breaks the default connection to '1V/Oct CV1'.
Osc1 Outoutput for VCO1-oscillator signaltriangle- to saw-waveform output, morvable manually or with external CVWaveform morvable with 'Wave1 CV'-pot and CV-signal.
Osc-Mix Outoutput for mixed VCO1-/VCO2-oscillator signalmixed signal from Osc1- and Osc2-outputsWaveforms fadeable between Osc1- and Osc2-signal outputs.
Fading can be done with 'Fade CV'-pot and CV-signal.
50%/50% Osc1/2-signal level on 'Osc-Mix Out', if 'Osc-Fade'-pot is in centerposition and no 'Fade CV' is plugged in.
Osc2 Outoutput for VCO2-oscillator signalsaw- to triangle-waveform output, morvable manuallyWaveform morvable with 'Wave2'-pot between saw- and triangle-signal.
Sync InSync-signal for VCO1 (optional VCO2)this signal can be switched to: 'Sync Hard', ' Sync Soft' or 'Off'This input is normalised with the 'Puls2 Out'-signal from VCO2.
Patch-cabel plugged in breaks the default connection to 'Puls2 Out'.
Mod Outoutput for modulation-signal controllable with 'Mod.Level CV'modulation-signal used for 'FMx Lin/Log' and 'PWM'
default sinusoidal-signal from VCO2 used for VCO1 modulation
sinusoidal-signal from VCO2 is available on this output if high impedance connection is used.
optional an external low impedance signal plugged in can overwride the internal modulation.
Puls2 Outoutput for puls-signal from VCO2output-signal for synchronisation and audio
the pulswith is controllable with 'PWM'-pot using the 'Mod Out'-signal
This output is also internally linked to 'Sync In'.
Bipolar output with +-5.0Volt level.

There are eight potentiometers with following functions:

Pot-NameFunctionCommentDetail
Tune 1Pitch for VCO1default pitch in center-positiontuning-range +-2 octaves.
Tune 2Pitch for VCO2default pitch in center-positiontuning-range +-2 octaves.
Osc-Fademanually fading between Osc1- and Osc2-signals on 'Osc-Mix Out'works as CV offset for the 'Fade CV'-signalpot to CCW: Osc2-signal output.
pot to CW: Osc1-signal output.
pot to centerposition: equal level output.
Fade CVCV Level amount pot for fading between Osc1- and Osc2-signals on 'Osc-Mix Out'works together with 'Osc-Fade' for fading Osc1/2-signalsCV Level adjustable between 0 ... max.
Wave1 CVCV Level amount pot for Osc1 waveform-selection on 'Osc1 out'manually selection of waveform is possible if no CV-signal is plugged inCV Level adjustable between 0 ... max.
Mod.Level CVCV Level amount pot for modulation controlmanually modulationlevel control is possible if no CV-signal is plugged inCV Level adjustable between 0 ... max.
PWMpulswith pot to control amount of PWMthe modulation-signal on 'Mod Out' is used for PWMPWM amount adjustable between 0 ... max.
Pulswith is 50% on 'Puls2 Out' if pot is in CCW-position (set to 0).
Wave2waveform selection pot for Osc2-signalmanually morving between saw- and triangle-signalpot to CCW: SAW-signal.
pot to CW: Triangle-signal.
pot to centerposition: mixed signal.

There are six switches to control the behaviour of signals.

SwitchFunctionCommentDetail
FM1-switchswitch for VCO1 FM modulation using signal on 'Mod Out'FM controll for VCO1FM1 Lin := Linear FM modulation.
Off := function off.
FM1 Log := Logarithmic FM modulation.
Sync-switchswitch for VCO1 Hard- or Soft-synchronisation with puls-signal from VCO2switched synchronisation-signal from 'Puls2 Out'Sync Hard := hard synced to VCO2.
Off := sync. function off.
Sync Soft := soft synced to VCO2.
VCO1 Octave-switchswitch for VCO1 pitch settingoctaves up or down depending on 'Octave switch + or -'1 := one octave (up/down).
2 := two octaves (up/down).
Octave up/down switchswitch for VCO1- and VCO2-switched pitchcontrolselecting pitch up or down for VCO1 and VCO2+ := pitch up.
- := pitch down.
VCO2 Octave-switchswitch for VCO2 pitch settingoctaves up or down depending on 'Octave switch + or -'1 := one octave (up/down).
2 := two octaves (up/down).
FM2-switchswitch for VCO2 FM modulation using signal on 'Mod Out'FM controll for VCO2FM1 Lin := Linear FM modulation.
Off := function off.
FM1 Log := Logarithmic FM modulation.


Technical data [blocked]

  • size:
    width: 16HP
    depth: 45mm

  • power:
    5Volt, 0 mA
    +12Volt, 60mA
    -12Volt, 60mA

  • frequency range: 20Hz to 20kHz.

  • frequency CV scale: 1V/Oct on '1V/Oct CV1'- and '1V/Oct CV2'-inputs.

  • frequency pot tuning range: +-2 Octaves.

  • frequency switchable pitch range: plus or minus 1 or 2 octaves for oscillator 1/2.

  • signal inputs, DC-coupled signal path.

  • signal outputs, DC-coupled signal path.

  • signal input impedance: > 50kOhm.

  • signal output impedance: 500 Ohm.

  • expandable with more '2MoreVO' dual-oscillator('s) used in master-/slave-configuration.

References [blocked]

License [blocked]

Hardware:cc by-nc-sa 4.0 (details)

Parts

77
QtyValueFootprintReferences
7100K 0.1%Resistor_SMD:R_0805_2012MetricR11, R13, R14, R15, R17, R18, R19
7100nFCapacitor_SMD:C_0805_2012MetricC1, C5, C6, C7, C8, C9, C10
7150KResistor_SMD:R_0805_2012MetricR35, R36, R37, R38, R40, R41, R43
610KResistor_SMD:R_0805_2012MetricR4, R22, R26, R28, R30, R34
41MResistor_SMD:R_0805_2012MetricR5, R6, R25, R33
3100KResistor_SMD:R_0805_2012MetricR32, R39, R44
320KResistor_SMD:R_0805_2012MetricR2, R8, R31
3Jumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mmJP1, JP2, JP3
21000nFCapacitor_SMD:C_0805_2012MetricC2, C3
210KPotentiometer_THT:Potentiometer_Bourns_3266Y_VerticalRV1, RV2
210nFCapacitor_SMD:C_0805_2012MetricC11, C13
21KResistor_SMD:R_0805_2012MetricR9, R29
2470Resistor_SMD:R_0805_2012MetricR7, R12
25.6KResistor_SMD:R_0805_2012MetricR1, R3
2BZX 384 4.7VDiode_SMD:D_SOD-323_HandSolderingD2, D3
2TestPointTestPoint:TestPoint_Keystone_5000-5004_MiniatureTP1, TP2
10RResistor_SMD:R_0805_2012MetricR42
11.5KResistor_SMD:R_0805_2012MetricR21
1100Resistor_SMD:R_0805_2012MetricR20
1100KPotentiometer_THT:Potentiometer_Bourns_3266Y_VerticalRV3
1120KResistor_SMD:R_0805_2012MetricR10
11N4148Diode_SMD:D_SOD-323_HandSolderingD1
11nFCapacitor_SMD:C_0805_2012MetricC12
11nFCapacitor_THT:C_Axial_L12.0mm_D6.5mm_P15.00mm_HorizontalCF1
120KPotentiometer_THT:Potentiometer_Bourns_3266Y_VerticalRV5
1220pFCapacitor_SMD:C_0805_2012MetricC14
1330nFCapacitor_SMD:C_0805_2012MetricC4
147KResistor_SMD:R_0805_2012MetricR16
1500Potentiometer_THT:Potentiometer_Bourns_3266Y_VerticalRV4
151KResistor_SMD:R_0805_2012MetricR45
1AS3340Package_DIP:DIP-16_W7.62mm_SocketU4
1Conn_01x08Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJ2
1Conn_01x10Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_VerticalJ1
1MCP1804x-1802xDBPackage_TO_SOT_SMD:SOT-89-3U1
1MMBT3906Package_TO_SOT_SMD:SOT-23Q1
1TL074Package_SO:SOIC-14_3.9x8.7mm_P1.27mmU2

The 76 most common of 77 parts.

More from ImoogDi/2MoreVO

1
  • 2 layers76.2 × 157.5 mm2MoreVO, the printed circuit board in 3D

    2MoreVO

    ImoogDi/2MoreVO

    Eurorack dual VCO using the public AS3340/CEM3340

    142 parts1

Similar boards

  • 4 layers99 × 53.3 mmPSLab, the printed circuit board in 3D

    PSLab

    fossasia/pslab-hardware

    PSLab Hardware Design and Schematics https://pslab.io

    199 parts1.7kApache-2.0
  • 2 layers68.8 × 53.6 mmRelatively Universal ROM Programmer, the printed circuit board in 3D

    Relatively Universal ROM Programmer

    AndersBNielsen/Relatively-Universal-ROM-Programmer

    Hardware to program W27C512 EEPROM or any 24/28/32 pin ROM requiring from 5V to 27V programming voltage.

    149 parts257GPL-3.0
  • 2 layers58 × 110 mmVco core, the printed circuit board in 3D

    Vco core

    shmoergh/moduleur

    Fully analog DIY-friendly modular synth

    146 parts222
  • 4 layers58 × 77.4 mmAWG, the printed circuit board in 3D

    AWG

    MatthiasElectronic/AWG_DHO8-900

    artificial waveform generator / function generator for DHO800 and DHO900 series (AWG/AFG)

    208 parts221CERN-OHL-W-2.0
  • 4 layers304.8 × 330.2 mm2000ATX, the printed circuit board in 3D

    2000ATX

    jasonsbeer/Amiga-2000-EATX

    An Amiga 2000 PCB in the EATX form factor.

    614 parts200GPL-3.0
  • 6 layers160 × 100 mmAdrmu6layer, the printed circuit board in 3D

    Adrmu6layer

    marcoreps/ADRmu

    ADR1000 10V standard

    240 parts149
  • 6 layers304.8 × 243.8 mmAmigaPCI MainBoard, the printed circuit board in 3D

    AmigaPCI MainBoard

    AmigaPCI/AmigaPCI-MainBoard

    Amiga with Native PCI Bus

    748 parts135

Questions

How big is the MoreVO Core PCB?

It measures 50.2 × 34.9 mm and has 2 copper layers, 1.6 mm thick.

What parts does the MoreVO Core use?

77 parts, built around the MMBT3906. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the MoreVO Core KiCad files?

From the ImoogDi/2MoreVO repository on GitHub, at the commit this page was made from: the board is hw/MoreVO_Core/MoreVO_Core.kicad_pcb and its schematic hw/2MoreVO.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the MoreVO Core design in my own project?

Its repository states no licence, so its author keeps all rights: ask ImoogDi before reusing the design.