

Hydroponics
Kicad designs and libraries
- Size
- 110 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 88
- Nets
- 68
- Pads
- 259
- Tracks, vias
- 354, 78
- Pours
- 18
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 15 Jun 2020
- Updated
- 3 Sep 2022
Overview
Hydroponics is an open-source printed circuit board by imagestream, from the imagestream/kicad repository on GitHub, published under the MIT licence. It is a 2-layer board of 110 × 100 mm with 88 parts on 68 nets, routed with 354 tracks and 78 vias.
It is built around the TPS82150SILR, AM2320 and B3FS-1000P, with the 907-111A1012D10200 and SK86 among its other parts. Its parts include 38 resistors, 16 capacitors, 9 connectors, 8 diodes and 6 ICs.
Main components
5TPS82150SILR
USIP-8-40℃~+125℃ 1 1.5mm 1A 2.8mm 20uA 2MHz 3V~17V 3mm 900mV~6V Over-temperature protection、Over Current Protection、Under Voltage Protection、Automatic fault recovery、Programmable output voltage、Light load efficient mode、Power-on timing control、Programmable soft start Step-down type USIP-8 DC-DC Power Modules ROHSTexas InstrumentsDC-DC Power ModulesAM2320
SIP-40%RH~99.9%RH 16bit 3.1V~5.5V 950uA I2C、Single-bus ±0.5℃ ±3%RH SIP-4 Temperature and Humidity Sensor ROHSAosong ElecTemperature And Humidity SensorB3FS-1000P
SMD-4P,6.3x6mm-25℃~+70℃ 1N 24V 3.1mm 50mA 6.3mm 6mm Gull Wing Round Button SPST Surface Mount,Vertical SMD-4P,6.3x6mm Tactile Switches ROHSOmronTactile Switches907-111A1012D10200
插件17.3mm 2 8P Female Right Angle Type-A USB 2.0 White 插件 USB Connectors ROHSJing Extension of the Electronic Co.USB ConnectorsSK86
SMB(DO-214AA)-55℃~+150℃ 100nA 150A 60V 700mV@8A 8A Independent SMB(DO-214AA) Schottky Diodes ROHSGOODWORKSchottky Diodes
README
README.mdkicad
Kicad designs and libraries
Parts
88| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 10K | Resistor_SMD:R_0603_1608Metric | R4, R5, R9, R17, R18, R19, R20, R21, R22, R23, R24, R31, R32, R33, R34 |
| 5 | 220 | Resistor_SMD:R_0603_1608Metric | R8, R10, R11, R13, R35 |
| 4 | 0 | Resistor_SMD:R_0603_1608Metric | R25, R26, R27, R28 |
| 4 | 100K | Resistor_SMD:R_0603_1608Metric | R1, R3, R6, R12 |
| 4 | MountingHole | MountingHole:MountingHole_3mm | H1, H2, H3, H4 |
| 3 | 10uF | Capacitor_SMD:C_1206_3216Metric | C2, C6, C10 |
| 3 | B3FS-1000P | B3FS-1000P:B3FS-1000P | S1, S2, S3 |
| 3 | RED | LED_SMD:LED_0805_2012Metric | D5, D7, D8 |
| 3 | Screw_Terminal_01x04 | LIB_691313410004:691313410004 | J1, J2, J5 |
| 3 | TestPoint | TestPoint:TestPoint_Plated_Hole_D2.0mm | TP1, TP2, TP3 |
| 2 | .01 | Resistor_SMD:R_Shunt_Vishay_WSR2_WSR3 | R29, R37 |
| 2 | .01 | Resistor_SMD:R_2512_6332Metric | R30, R38 |
| 2 | .1uF | Capacitor_SMD:C_0603_1608Metric | C15, C16 |
| 2 | 1uF | Capacitor_SMD:C_0805_2012Metric | C8, C9 |
| 2 | 282834-3 | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-3_1x03_P2.54mm_Horizontal | J8, J9 |
| 2 | 430pF | Capacitor_SMD:C_0603_1608Metric | C3, C5 |
| 2 | 47uF | Capacitor_SMD:C_1206_3216Metric | C1, C4 |
| 2 | 523K | Resistor_SMD:R_0603_1608Metric | R2, R7 |
| 2 | INA219AxDCN | Package_TO_SOT_SMD:SOT-23-8 | U2, U3 |
| 2 | TPS82150SILR | TPS82150SILR:TPS82130SILT | IC1, IC2 |
| 1 | 1.5nF | Capacitor_SMD:C_0805_2012Metric | C13 |
| 1 | 100nF | Capacitor_SMD:C_0805_2012Metric | C11 |
| 1 | 187K | Resistor_SMD:R_0603_1608Metric | R14 |
| 1 | 2.32K | Resistor_SMD:R_0603_1608Metric | R16 |
| 1 | 27nF | Capacitor_SMD:C_0603_1608Metric | C12 |
| 1 | 282834-2 | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-2_1x02_P2.54mm_Horizontal | J10 |
| 1 | 2K 0.25W | Resistor_SMD:R_0603_1608Metric | R36 |
| 1 | 33uF | Capacitor_SMD:C_Elec_6.3x7.7 | C7 |
| 1 | 47nF | Capacitor_SMD:C_0805_2012Metric | C14 |
| 1 | 60.4K | Resistor_SMD:R_0603_1608Metric | R15 |
| 1 | 7.8uH | Scott:L_TDK_RLF12560 | L1 |
| 1 | AM2320 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | U1 |
| 1 | BLUE | LED_SMD:LED_0805_2012Metric | D4 |
| 1 | C2341 | LIB_C2341:C2341 | J6 |
| 1 | Conn_01x12_Female | Connector_PinSocket_2.54mm:PinSocket_1x12_P2.54mm_Vertical | J4 |
| 1 | Conn_01x16_Female | Connector_PinSocket_2.54mm:PinSocket_1x16_P2.54mm_Vertical | J3 |
| 1 | GREEN | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | PDS760-13 | Diode_SMD:D_PowerDI-5 | D6 |
| 1 | SK86 | Diode_SMD:D_SMC | D1 |
| 1 | TPS55340PWPR | TPS55340PWPR:SOP65P640X120-15N | IC3 |
| 1 | YELLOW | LED_SMD:LED_0805_2012Metric | D3 |
More from imagestream/kicad
12- 6 layers150 × 160 mm

- 6 layers150 × 160 mm

- 4 layers186 × 226 mm

- 4 layers186 × 226 mm

- 2 layers186 × 226 mm

- 4 layers108 × 110 mm

- 4 layers105 × 105 mm

- 2 layers186 × 226 mm

- 2 layers186 × 226 mm

- 2 layers186 × 226 mm

- 2 layers186 × 226 mm

- 2 layers50.8 × 22.9 mm

Similar boards
- 6 layers50 × 49.4 mm

PCB BRUSHED
mathieupommery/ESE_2526_ROBOTCHATDELAMUERTE
We first wanted to make a three omniwheeled robot with FOC control on brushless motors.
93 parts1 - 4 layers100 × 80 mm

- 4 layers100 × 100 mm

- 2 layers122 × 122 mm

BikeCounter SingleBoard
guidosch/bikecounter
This repository contains the hardware and software components of a PIR based tracking device to monitor the usage of local bike trails.
23 parts6CC0-1.0 - 2 layers118 × 105 mm

FilamentStorage
LilisProtoLab/FDM-print-station
The FDM print station of Lili's Proto Lab contains six printers, three printer enclosures and a dry-air filament drawer
84 partsMIT - 4 layers66 × 57 mm

A1-External ESP8266-Cooling Fan Module
potpurri/A1-External-ESP8266-Cooling-Fan-Module
ESP8266-board driving an external fan for improved cooling of nozzle and prints
74 partsApache-2.0 - 2 layers93 × 61 mm

MainPcb v 1 0
powermosfet/mqtt-button
A generic IoT device with two buttons, two LED's and a temperature/humidity sensor
22 parts - 2 layers60 × 50 mm

Questions
How big is the Hydroponics PCB?
It measures 110 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Hydroponics use?
88 parts, built around the TPS82150SILR, AM2320, B3FS-1000P and 907-111A1012D10200. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Hydroponics KiCad files?
From the imagestream/kicad repository on GitHub, at the commit this page was made from: the board is Hydroponics/Hydroponics.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Hydroponics design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).