2 layers
2 layers45.7 × 31.8 mm
Glider RX SMD
house4hack/nrf-gliderGlider using NRF24L01
- Size
- 45.7 × 31.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 22
- Nets
- 24
- Pads
- 89
- Tracks, vias
- 222, 15
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 17 Sep 2016
- Updated
- 28 May 2019
Overview
Glider RX SMD is an open-source printed circuit board by house4hack, from the house4hack/nrf-glider repository on GitHub. It is a 2-layer board of 45.7 × 31.8 mm with 22 parts on 24 nets, routed with 222 tracks and 15 vias.
It is built around the MSP430G2553IPW28 and LM1117-3.3. Its parts include 5 resistors, 3 capacitors, 3 ICs, 1 diode and 1 connector. It belongs with the MSP430 boards of this library.
Main components
2
MSP430G2553IPW28
TSSOP-28-40℃~+85℃ 1.8V~3.6V 10bit 16 Bit 16KB 16MHz 24 512Byte Built-in FLASH MSP430 CPU16 TSSOP-28 Microcontrollers (MCU/MPU/SOC) ROHSTexas InstrumentsMicrocontrollers (MCU/MPU/SOC)
LM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorised
Parts
22| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | Servo Left | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | M1, M3, M4, M5, M6 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R5 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1 |
| 1 | 10uF | Capacitor_SMD:CP_Elec_5x5.8 | C2 |
| 1 | 20k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R4 |
| 1 | 220 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R3 |
| 1 | 22uF Tan | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A_Pad1.58x1.35mm_HandSolder | C3 |
| 1 | 4.5V - 7.2V | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | BT1 |
| 1 | 47k | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R2 |
| 1 | 4k7 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1 |
| 1 | Buzzer | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | BZ1 |
| 1 | LED | LED_SMD:LED_1206_3216Metric_Pad1.42x1.75mm_HandSolder | D1 |
| 1 | LM1117-3.3 | Package_TO_SOT_SMD:SOT-223 | U3 |
| 1 | MSP430G2553IPW28 | Package_SO:TSSOP-28_4.4x9.7mm_P0.65mm | U1 |
| 1 | NRF24L01_Breakout | mysensors_radios:NRF24L01-SMD | U2 |
| 1 | PROG | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | Pair | Button_Switch_SMD:SW_SPST_FSMSM | SW1 |
| 1 | Servo Right | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | M2 |
More from house4hack/nrf-glider
2- 2 layers
Similar boards
- 2 layers50 × 65 mm
Nsumo
artfulbytes/nsumo_hardware
A 2-layer PCB for a small sumobot including MSP430G2553, regulators, motor drivers, and IR receiver.
81 parts34MIT - 2 layers79 × 89 mm
Bms v1
azerimaker/BMS_3-5S
3-5S Battery Management System based on TI bq76920 IC and MSP430 uC.
175 parts22 - 2 layers21.6 × 60 mm
CheeseDip
upsidedownlabs/MSP430-Breadstick
Texas Instrument MSP430G2553 based development board.
63 parts22 - 2 layers52.9 × 22.9 mm
MSP430G2553-Feather
upsidedownlabs/MSP430G2553-Feather
MSP430G2553 based Adafruit feather compatible board 🪶
76 parts10 - 2 layers24 × 42 mm
- 2 layers160 × 35 mm
- 4 layers56 × 40 mm
Ver2 transmiteer
tonycung/0-10V-to-4-20mA-Converter
A simple 0–10 V to 4–20 mA analog signal converter designed with KiCad.
66 parts - 2 layers33.7 × 97.8 mm
HAN ESP TSS721
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported
29 parts470
Questions
How big is the Glider RX SMD PCB?
It measures 45.7 × 31.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Glider RX SMD use?
22 parts, built around the MSP430G2553IPW28 and LM1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Glider RX SMD KiCad files?
From the house4hack/nrf-glider repository on GitHub, at the commit this page was made from: the board is docs/nrf_glider/glider_RX_SMD.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Glider RX SMD design in my own project?
Its repository states no licence, so its author keeps all rights: ask house4hack before reusing the design.