Skip to the content
2 layers60 × 50 mmLCC Interface, the printed circuit board in 3D

LCC/OpenLCB CAN interface board (KiCad): TCAN332, dual RJ45, termination jumper, test points, LEDs (mirror of Forgejo)

Size
60 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
27
Nets
16
Pads
73
Tracks, vias
197, 5
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
21 Oct 2026
Updated
21 Oct 2026

Overview

LCC Interface is an open-source printed circuit board by honzup, from the honzup/LCC_Interface_KiCad repository on GitHub, published under the CERN-OHL-P-2.0 licence. It is a 2-layer board of 60 × 50 mm with 27 parts on 16 nets, routed with 197 tracks and 5 vias.

It is built around the PESD1CAN. Its parts include 6 resistors, 4 diodes, 3 connectors, 2 capacitors and 1 IC. It belongs with the interfaces and adapters boards of this library.

Main components

1

README

README.md

LCC / CAN interface board – Rev C

A small two-layer board that connects any 3.3 V microcontroller with a CAN controller (ESP32 TWAI, STM32, …) to an LCC / OpenLCB bus using standard RJ45 cables. Designed in KiCad for model railway layouts; in daily use on my layout under every LCC node and the Ethernet bridge (lcc-eth-bridge).

Rev C, top

Why a dedicated board rather than a ready-made transceiver module:

  • RJ45 in and out – robust connectors and ordinary straight-through patch leads; the bus daisy-chains through the board, so unplugging the processor doesn't break the bus.
  • Termination by jumper – fit JP1 only on the boards at the two ends of the bus. (Many ready-made SN65HVD230 modules have a 120 Ω resistor soldered on permanently.)
  • Test points and LEDs – probe pads for CAN_H, CAN_L, CAN_GND, 3V3, TX and RX, plus power / TX / RX LEDs: you can see at a glance whether the board has power, whether the node transmits and whether it hears the bus.
  • ESD protection on the bus lines (PESD1CAN TVS diode), shields tied to CAN ground.
  • TCAN33x footprint – built with a TCAN332; also takes the TCAN330/334/337.

Specification

  • Transceiver U1: TI TCAN332DR, 3.3 V, SOIC-8. LCC's 125 kbit/s is far inside its rating.
  • J1/J2: Amphenol RJHSE-5380 shielded RJ45, no magnetics. Do not substitute an Ethernet MagJack – its transformers block CAN. Not the -5385 (LED) variant either.
  • J3: 4-pin 2.54 mm header to the microcontroller: 1 GND, 2 3V3, 3 TX, 4 RX. The board is powered from the microcontroller's 3.3 V – wire GND and 3V3, not just TX/RX.
  • All eight RJ45 conductors pass straight through J1 ↔ J2. Bus power (pins 7/8) is pass-through only and is not connected to the board's supply. Non-isolated design.
  • 60 × 50 mm, two layers, 1.6 mm, solid CAN_GND pour on the bottom. Four M3 mounting holes, 4 mm in from each corner (52 × 42 mm pattern).

RJ45 pinout (LCC standard S-9.7.1.1)

PinSignalT568B colour
1CAN_Hwhite/orange
2CAN_Lorange
3CAN_GNDwhite/green
4ALT_L (pass-through)blue
5ALT_H (pass-through)white/blue
6CAN_GNDgreen
7PWR_NEG (pass-through)white/brown
8PWR_POS (pass-through)brown
shellCAN_GND

CAN_H/CAN_L share one twisted pair, so ordinary straight-through Cat5e/Cat6 patch leads work. Never use crossover or flat (untwisted) cable.

Ordering and assembly

  • PCB: upload LCC_Interface_RevC_gerbers.zip to any fab (JLCPCB, PCBWay …): 2 layers, 1.6 mm, default settings.
  • Parts: BOM.csv (with Digi-Key part numbers) and digikey-order.txt (paste into Digi-Key's quick order). bom/ibom.html is an interactive BOM – open it in a browser while soldering to highlight each part's position.
  • Hand soldering: all SMD parts are 0805 or SOIC-8/SOT-23 with hand-solder pads. R2/R3 are not fitted for the TCAN332 – fit them only for a TCAN330/334/337, where they hold the mode pins low.
  • Reflow all eight U1 pins. Cold joints on hand-soldered SOIC-8s tend to come in groups; if a fresh board misbehaves, reflow the whole chip rather than chasing one pin at a time.
  • LED colours: the LEDs run from 3.3 V through 1 kΩ. Use red, orange, yellow or standard green (≈2 V forward voltage). Blue, white and "true" green (≈3 V) are barely visible at this current.

Bring-up checks

With the board powered and connected to the bus:

CheckExpect
PWR LEDon
3V3 test point (TP4)3.3 V
CAN_H and CAN_L to CAN_GND, bus idleboth ≈ 1.9 V – normal for a 3.3 V transceiver, not the 2.5 V of 5 V parts
TX / RX test points, bus idle≈ 3.3 V (high = recessive)
RX LEDflickers on any bus traffic
TX LEDflickers only when this node transmits
CAN_H ↔ CAN_L, everything powered off≈ 60 Ω with both ends terminated; ≈ 120 Ω means only one end

RX flickering with TX dark means the node hears the bus but isn't transmitting – check the TX wire and the node firmware.

Files

FileWhat
LCC_Interface.kicad_pro / .kicad_sch / .kicad_pcbKiCad project (made in KiCad 10; the schematic is the source of truth)
LCC_Interface_RevC_gerbers.zip (+ unzipped folder)Gerbers and drill files for ordering
BOM.csv, digikey-order.txt, bom/ibom.htmlBill of materials, Digi-Key order, interactive BOM
images/Renders

Revision history

  • Rev C (current) – adds power / TX / RX LEDs and test points for 3V3, TX and RX. No circuit change. Tag rev-c.
  • Rev B – first manufactured version. Common ground between the board and the bus, PESD1CAN ESD protection, 4.7 µF bulk capacitor, shielded RJ45s, TCAN33x-family footprint. Tag rev-b.
  • Rev A – an AI-drafted schematic whose net labels had landed on the wrong pins (TX/RX and CAN_H/CAN_L swapped, RJ45 pinout mirrored) – a reminder to check every pin against the datasheets.

Licence

CERN Open Hardware Licence v2 – Permissive (CERN-OHL-P-2.0) – see LICENSE.

Parts

27
QtyValueFootprintReferences
6TPTestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mmTP1, TP2, TP3, TP4, TP5, TP6
4MountingHole:MountingHole_3.2mm_M3H1, H2, H3, H4
31kResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR4, R5, R6
3LEDLED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolderD2, D3, D4
210k DNPResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR2, R3
2LCC RJ45Connector_RJ:RJ45_Amphenol_RJHSE5380J1, J2
1100nFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC1
1120RResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR1
14.7uFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC2
1MCU INTERFACEConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ3
1PESD1CANPackage_TO_SOT_SMD:SOT-23D1
1TCAN332DRPackage_SO:SOIC-8_3.9x4.9mm_P1.27mmU1
1TERM ENABLEConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJP1

Similar boards

  • 4 layers113.5 × 105.5 mmMultistepper, the printed circuit board in 3D

    Multistepper

    eddyem/stm32samples

    Code samples and ready projects based on bare-metal STM32

    243 parts208
  • 2 layers87.5 × 70 mm010 Implementation, the printed circuit board in 3D

    010 Implementation

    NewTec-GmbH/esp32-can-iot

    A ESP32 based interface between CAN-bus and IoT environments.

    70 parts51BSD-3-Clause
  • 4 layers56 × 43.3 mmStepperServoCAN, the printed circuit board in 3D

    StepperServoCAN

    dzid26/StepperServo-hardware

    Stepper actuator controller

    155 parts29GPL-3.0
  • 4 layers92 × 95 mmESP32-CAN, the printed circuit board in 3D

    ESP32-CAN

    Eric-2012/ESP32-CAN

    251 parts5
  • 2 layers57 × 70 mmFlexray harness, the printed circuit board in 3D

    Flexray harness

    I-CAN-hack/flexray-harness

    64 parts5MIT
  • 2 layers109 × 95 mmStm32, the printed circuit board in 3D

    Stm32

    eddyem/tsys01

    BTA primary mirror thermal monitoring using STM32 and TSYS01

    93 parts4GPL-3.0
  • 2 layers43 × 43 mmESP32-Touch board, the printed circuit board in 3D

    ESP32-Touch board

    kamil2466/SiD-ON

    Smart Home Projects

    49 parts4GPL-3.0
  • 4 layers103.5 × 48.3 mmButtonBd2, the printed circuit board in 3D

    ButtonBd2

    frc971/electrical

    This repo contains the electrical files for the 971 FRC team. The files include PCBs and the electrical system diagrams. The PCBs are created using KiCad.

    165 parts3Apache-2.0

Questions

How big is the LCC Interface PCB?

It measures 60 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the LCC Interface use?

27 parts, built around the PESD1CAN. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the LCC Interface KiCad files?

From the honzup/LCC_Interface_KiCad repository on GitHub, at the commit this page was made from: the board is LCC_Interface.kicad_pcb and its schematic LCC_Interface.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the LCC Interface design in my own project?

Its repository publishes it under the CERN-OHL-P-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).