

StepperServoCAN
Stepper actuator controller
- Size
- 56 × 43.3 mm
- Copper layers
- 4
- Thickness
- 1.16 mm
- Parts
- 155
- Nets
- 89
- Pads
- 457
- Tracks, vias
- 1,910, 406
- Pours
- 909
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 21 Aug 2022
- Updated
- 30 Sep 2026
Overview
StepperServoCAN is an open-source printed circuit board by dzid26, from the dzid26/StepperServo-hardware repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 56 × 43.3 mm with 155 parts on 89 nets, routed with 1,910 tracks and 406 vias.
It is built around the STM32F103CBT6, SN65HVD230D and LMV321, with the ADMT4000BRUZAB-R7, LV2842XLVDDCR-JSM and 1N5819WS among its other parts. Its parts include 50 resistors, 34 capacitors, 22 diodes, 10 ICs and 4 transistors. It belongs with the robots and motor control boards and the STM32 boards of this library.
Main components
12STM32F103CBT6
LQFP-48(7x7)-40℃~+85℃ 128KB 12bit 20KB 2V~3.6V 32 Bit 37 72MHz ARM Cortex-M3 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)SN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversLMV321
SOT-23-5L-2.75V~-1.25V、1.25V~2.75V 0℃~+70℃ 1 10pA 10pA 1MHz 2.1V~5.5V 20mA 20nV/√Hz@10kHz 520V/ms 60uA 70dB 800uV Built-in compensation Rail-to-Rail Input, Rail-to-Rail Output SOT-23-5L Operational Amplifier ROHSJiangsu Changjing Electronics Technology (CJ)Operational AmplifierADMT4000BRUZAB-R7
TSSOP-24-40℃~+150℃ 12bit 16mT 18mA 3V~3.6V SPI Under-voltage lockout、Overvoltage lockout、Built-in temperature sensor TSSOP-24 Magnetic Angle Sensors ROHSAnalog DevicesMagnetic Angle SensorsLV2842XLVDDCR-JSM
TSOT-23-6L-40℃~+125℃ 1 1A 1MHz 4.6V~40V 80uA Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting Step-down type Yes TSOT-23-6L DC-DC Converters ROHSJSMSEMIDC-DC Converters1N5819WS
SOD-3231 Independent 1A 25A 40V 500uA@40V 600mV@1A SOD-323 Schottky Diodes ROHSGuangdong HottechSchottky DiodesAO3401A
SOT-231 P-Channel 14nC@10V 30V 47mΩ@10V、60mΩ@4.5V、85mΩ@2.5V 4A 55pF 645pF 80pF 900mV SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsDSK34
SOD-123FL-55℃~+125℃ 3A 40V 500uA 520mV@3A 80A Independent SOD-123FL Schottky Diodes ROHSTWGMCSchottky DiodesPESD1CAN
SOT-23-65℃~+150℃ 11pF 1nA 2 200W@8/20us 24V 30.3V 3A@8/20us 70V Bidirectional ESD IEC 61000-4-2、IEC 61000-4-5 SOT-23 ESD and Surge Protection (TVS/ESD) ROHSNexperiaESD And Surge Protection (TVS/ESD)SMCJ28CA
SMC(DO-214AB)ESD And Surge Protection (TVS/ESD)hongjiachengSMF30CA
SOD-123FL-55℃~+150℃ 1uA 200W@10/1000us 30V 36.8V 4.1A@10/1000us 48.4V Bidirectional IEC 61000-4-2 TVS SOD-123FL ESD and Surge Protection (TVS/ESD) ROHShongjiachengESD And Surge Protection (TVS/ESD)SSL54
SMASchottky Diodeshongjiacheng
README
README.mdStepperServoCAN Firmware
https://github.com/dzid26/StepperServoCAN
StepperServo-hardware
Limits:
- 3.3A peak stall current per phase for 5sec
- 3.3A RMS combined motor continuous current for >1min (i.e. rotating under load but not stalled)
- 32V supply voltage
Features:
-
Intended to drive a stepper motor
-
High impedance freewheeling with overvoltage protection
-
Magnetic angle sensor (can be turned off during sleep)
-
CANbus transceiver with standby mode
-
Debug port for flashing and configuration with ESD protection
-
Low-side current, V_mot and V_Bat, PCB temperature measurements
-
Reverse polarity protection and swapped connectors protection; ESD protections on inputs
-
Optional Enable port with Break interrupt capability for additional safety
-
Optional expansion port for connecting UART/I2C/PWM device or a sensor (0.4A max, or 1A for v0.6)
-
Optional solder jumper pads, e.g. for motor identification
Schematic
PCB
- single sided PCB for direct mounting on the motor and efficient assembly
- flat bottom allows for heat dissipation and measuring motor temperature
Motor
Motor tips:
- an examples of motor that produce a lot of torque without needing much gear ratio are Nema23 104mm and 56mm - they have dense windings and high torque per amp values
- for space limited applications this coupled with single stage 5:1 gearbox can provide enough torque with relatively low friction and noise from the gearbox. Note: above 2Amps, the torque tapers off and torque ripple becomes apparent!
- rated current should not be exceeded by a lot to avoid torque ripple, motor inefficiency and overheating
- motors with high rated-current (less but thicker winding) can be used to avoid torque ripple problem, provided they are geared enough to generate enough output torque - however large gear ratios can be more prone to backlash and low efficiency which adds to backdrivinility friction
- generally big motors will have smoothest torque and don't need that much gearing
Angle sensor magnet
Parts
155| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 100n | Capacitor_SMD:C_0402_1005Metric | C2, C3, C4, C5, C9, C14, C16, C17, C18, C24, C31, C34, C35, C39 |
| 14 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R5, R7, R8, R9, R10, R11, R14, R16, R25, R26, R31, R33, R39 |
| 13 | 1N5819WS | Diode_SMD:D_SOD-323 | D4, D6, D7, D8, D9, D10, D11, D12, D13, D14, D15, D16, D17 |
| 6 | WirePad | TestPoint:TestPoint_Pad_2.0x2.0mm | TP4, TP5, TP6, TP8, TP9, TP10 |
| 5 | 100k | Resistor_SMD:R_0402_1005Metric | R20, R22, R30, R41, R48 |
| 5 | 10k | Resistor_SMD:R_0402_1005Metric | R2, R6, R15, R36, R38 |
| 5 | 56k | Resistor_SMD:R_0402_1005Metric | R12, R13, R23, R40, R50 |
| 5 | 8.2k | Resistor_SMD:R_0402_1005Metric | R24, R28, R29, R37, R49 |
| 4 | 10n | Capacitor_SMD:C_0402_1005Metric | C8, C20, C22, C33 |
| 4 | Nema23 | MountingHole:MountingHole_3.2mm_M3_ISO14580_Pad_TopOnly | H1, H2, H3, H4 |
| 4 | Pad | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3, TP7 |
| 3 | 100n 50V | Capacitor_SMD:C_0402_1005Metric | C10, C36, C38 |
| 3 | 22u | Capacitor_SMD:C_0603_1608Metric | C1, C6, C40 |
| 3 | 5.6k | Resistor_SMD:R_0402_1005Metric | R17, R18, R45 |
| 3 | JLCPCB_ToolingHole | part:JLCPCB_ToolingHole | , , |
| 2 | 0.1R | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R27, R32 |
| 2 | 10p | Capacitor_SMD:C_0402_1005Metric | C11, C12 |
| 2 | 2.2k | Resistor_SMD:R_0402_1005Metric | R19, R21 |
| 2 | 220pF | Capacitor_SMD:C_0402_1005Metric | C21, C23 |
| 2 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q2, Q4 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R34, R35 |
| 2 | 470 | Resistor_SMD:R_0603_1608Metric | R42, R43 |
| 2 | A4950 | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalVias | U3, U4 |
| 2 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q1, Q3 |
| 2 | DSK34 | Diode_SMD:D_SOD-123F | D18, D20 |
| 2 | Fcn> | Button_Switch_SMD:SW_SPST_TL3342 | F1, F2 |
| 2 | I2C_PU | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP10, JP11 |
| 2 | Jumper | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | ID1, ID2 |
| 2 | LMV321 | Package_TO_SOT_SMD:SOT-23-5 | U6, U7 |
| 2 | Nema17 | MountingHole:MountingHole_3.2mm_M3_ISO14580_Pad_TopOnly | H5, H6 |
| 1 | 100 | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 100uF 35V | Capacitor_SMD:CP_Elec_6.3x5.7 | C27 |
| 1 | 10u | Capacitor_SMD:C_1206_3216Metric | C29 |
| 1 | 10u | Capacitor_SMD:C_0805_2012Metric | C37 |
| 1 | 120Ω | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R44 |
| 1 | 15k | Resistor_SMD:R_0402_1005Metric | R47 |
| 1 | 16Mhz 9pF | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1u | Capacitor_SMD:C_0402_1005Metric | C7 |
| 1 | 1u 25V | Capacitor_SMD:C_0402_1005Metric | C32 |
| 1 | 1uF 50V | Capacitor_SMD:C_0805_2012Metric | C13 |
| 1 | 22uH | Inductor_SMD:L_Changjiang_FTC252010S | L2 |
| 1 | 3.3 | TestPoint:TestPoint_Pad_D1.0mm | TP12 |
| 1 | 4.7k | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 51k | Resistor_SMD:R_0402_1005Metric | R46 |
| 1 | 68n | Inductor_SMD:L_0603_1608Metric | L1 |
| 1 | ADMT4000BRUZAB-R7 | Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm | U9 |
| 1 | BLUE | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | CAR | Connector_JST_SMD:JST-S4B-XH-SM4-TB | J1 |
| 1 | Conn_01x06 | TerminalBlock_TE-Connectivity:TerminalBlock_TE_282834-6_1x06_P2.54mm_Horizontal | J4 |
| 1 | Debug | Connector_JST_SMD:JST-S4B-XH-SM4-TB | J2 |
| 1 | FerriteBead 200mA | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | LV2842XLVDDCR | Package_TO_SOT_SMD:TSOT-23-6 | U11 |
| 1 | Motor | Connector_JST_SMD:JST-S4B-XH-SM4-TB | J3 |
| 1 | PESD1CAN | Package_TO_SOT_SMD:SOT-23 | D22 |
| 1 | RED | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | Rst | Button_Switch_SMD:SW_SPST_TL3342 | SW1 |
| 1 | SMCJ28CA | Diode_SMD:D_SMC | D5 |
| 1 | SMF30CA | Diode_SMD:D_SMF | D19 |
| 1 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U5 |
| 1 | SSL54 | Diode_SMD:D_SMB | D3 |
| 1 | STM32F103CBT6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | TLE5012B | tle_foot:Infineon-TLE5012-Level_A | U2 |
| 1 | TMAG5170-Q1 | Package_SO:VSSOP-8_3x3mm_P0.65mm | U8 |
| 1 | Yellow | LED_SMD:LED_0603_1608Metric | D21 |
Similar boards
- 2 layers25.3 × 61 mm

- 2 layers75.7 × 53.7 mm

- 2 layers57.7 × 44.5 mm

Contactor Board Schematic
Jack-p-hammer/HeartBridge
Software, electronics, mechanical parts and simulation for HeartBridge, an automated CPR machine. The project started as MIT 2.009 Green Team's 2025 class project and has continued since.
16 parts2 - 6 layers50 × 23 mm

Esp32p4amoled3.19
v-cu/dpf-load-monitor-wide
ESP32-P4 diagnostic display for VAG diesels — live DPF and engine data over CAN (UDS) on a 3.19" ultra-wide AMOLED. Firmware, KiCad files, BOM and 3D enclosure.
115 parts12 - 4 layers408.7 × 50 mm

Partial Drawer Controller v1
Robast-GmbH/PCB_Designs
This repository contains all the necessary files and instructions for the PCBs that are designed using KiCad. Here is an overview of the main components: - .github: Contains Github-specific configurations, including…
619 parts1MIT - 2 layers43 × 43 mm

- 4 layers50 × 30 mm

- 4 layers69.5 × 62.6 mm

Sensors Module
Queens-Rocket-Engineering-Team/Avionics-23-26
QRET Avionics hardware, firmware, and documentation for 2023 to 2025.
197 parts4
Questions
How big is the StepperServoCAN PCB?
It measures 56 × 43.3 mm and has 4 copper layers, 1.16 mm thick.
What parts does the StepperServoCAN use?
155 parts, built around the STM32F103CBT6, SN65HVD230D, LMV321 and ADMT4000BRUZAB-R7. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the StepperServoCAN KiCad files?
From the dzid26/StepperServo-hardware repository on GitHub, at the commit this page was made from: the board is PCB/StepperServoCAN.kicad_pcb and its schematic PCB/DCDC_3.3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the StepperServoCAN design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).