4 layers38 × 53 mm
2 layers92.9 × 54.5 mm
SaponseEx
hide4096/SaponseEx1- Size
- 92.9 × 54.5 mm
- Copper layers
- 2
- Thickness
- 0.8 mm
- Parts
- 91
- Nets
- 96
- Pads
- 368
- Tracks, vias
- 746, 252
- Pours
- 121
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 28 Jul 2022
- Updated
- 29 Jul 2023
Overview
SaponseEx is an open-source printed circuit board by hide4096, from the hide4096/SaponseEx repository on GitHub. It is a 2-layer board of 92.9 × 54.5 mm with 91 parts on 96 nets, routed with 746 tracks and 252 vias.
It is built around the AS5047P-ATSM, ICM-20648 and SSSS810701, with the BSS138, LBC3225T470KR and 1N4148W among its other parts. Its parts include 24 capacitors, 23 resistors, 12 ICs, 10 connectors and 6 transistors. It belongs with the STM32 and NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
9
AS5047P-ATSM
TSSOP-14_4.4x5.0x0.65P-40℃~+125℃ 0°~360° 1.2mm 15mA 4.4mm 4.5V~5.5V 5mm Magnetic rotary position sensor No SPI TSSOP-14 Position Sensors ROHSAdvanced Monolithic SystemsPosition Sensors
ICM-20648
QFN-24(3x3)-40℃~+85℃ 1.71V~3.6V 16bit IMU (accelerometer + gyroscope) SPI、I2C Synchronization and timestamp X,Y,Z X,Y,Z ±16g ±2000dps QFN-24(3x3) Accelerometers ROHSTDK InvenSenseAccelerometers
SSSS810701
SMD-40℃~+85℃ 10,000 cycles 300mA 4.1mm 5V Rectangular Columnar SMD(SMT) Tab SPDT Surface Mount, Right Angle SMD Slide Switches ROHSALPSALPINESlide Switches
BSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETs
LBC3225T470KR
1210220mA 47uH 670mΩ Wire-wound inductor ±10% 1210 Power Inductors ROHSTaiyo YudenPower Inductors
1N4148W
SOD-123150mA 1A 1V@50mA 1uA@75V 400mW 4ns 75V Independent SOD-123 Switching Diodes ROHSSTMicroelectronicsSwitching DiodesIRLML6344
SOT-23-55℃~+150℃ 1 N-channel 1.1V 1.3W 29mΩ@4.5V 30V 46pF 5A 6.8nC@4.5V 650pF SOT-23 MOSFETs ROHSGuangdong HottechMOSFETsIRLML6402
SOT-23-55℃~+150℃ 1 P-Channel 1.3W 110pF 12nC 145pF 20V 3.7A 400mV 633pF 65mΩ@4.5V P-Channel SOT-23 MOSFETs ROHSGuangdong HottechMOSFETs
SG-210STF
SMD2520-4P-40℃~+85℃ 1.6V~3.6V 1.8mA 13MHz ±50ppm SMD2520-4P Crystal Oscillators ROHSSeiko EpsonOscillators
README
README.mdSaponseEx
マイクロマウス RT社HM-Starterキットをベースに開発
Parts
91| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 0.1μ | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C5, C6, C7, C9, C10, C12, C13, C14, C16, C17, C18, C19, C21, C22, C23, C24 |
| 6 | 47k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R6, R8, R10, R12, R15 |
| 4 | 0 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R20, R21, R22, R23 |
| 4 | 1M | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7, R9, R11, R13 |
| 4 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R4, R17, R18, R19 |
| 4 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4 |
| 4 | LBR-127HLD | LBR-127HLD:LBR-127HLD | U1, U2, U3, U4 |
| 4 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D3, D4, D5 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2, R5, R16 |
| 3 | 1μ | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C15 |
| 2 | 47μ | Capacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolder | C8, C11 |
| 2 | AS5047P-ATSM | SamacSys:SOP65P640X120-14N | IC1, IC2 |
| 2 | DRV8212DSGR | SamacSys:SON50P200X200X80-9N | U7, U8 |
| 2 | LBC3225T470KR | SamacSys:VARC3225X270N | RV1, RV2 |
| 2 | LOGO | My:penpen | G***, G*** |
| 2 | MK06-4.5 | My:Motor | M2, M3 |
| 1 | 0.33μ | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3 |
| 1 | 10 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 1N4148W | Diode_SMD:D_SOD-123 | D2 |
| 1 | 2.2μ | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4 |
| 1 | 30 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R14 |
| 1 | 4.7μ | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C20 |
| 1 | CONN_BATT | SamacSys:SHDR2W35P0X125_1X2_425X320X420P | J1 |
| 1 | Conn_A_Main | Connector_PinHeader_1.27mm:PinHeader_1x06_P1.27mm_Vertical | J2 |
| 1 | Conn_A_Sub | Connector_PinHeader_1.27mm:PinHeader_1x06_P1.27mm_Vertical | J10 |
| 1 | Conn_B_Main | Connector_PinHeader_1.27mm:PinHeader_1x08_P1.27mm_Vertical | J3 |
| 1 | Conn_B_Sub | Connector_PinHeader_1.27mm:PinHeader_1x08_P1.27mm_Vertical | J9 |
| 1 | Conn_ENC_L | Connector_PinHeader_1.27mm:PinHeader_1x06_P1.27mm_Vertical | locked |
| 1 | Conn_ENC_R | Connector_PinHeader_1.27mm:PinHeader_1x06_P1.27mm_Vertical | J7 |
| 1 | Conn_MCU_L | Connector_PinHeader_1.27mm:PinHeader_1x06_P1.27mm_Vertical | J11 |
| 1 | Conn_MCU_R | Connector_PinHeader_1.27mm:PinHeader_1x06_P1.27mm_Vertical | J8 |
| 1 | Fan | My:Motor | M1 |
| 1 | FerriteBead | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | FB1 |
| 1 | ICM-20648 | SamacSys:QFN40P300X300X95-25N-D | IC3 |
| 1 | IRLML6344 | Package_TO_SOT_SMD:SOT-23 | Q6 |
| 1 | IRLML6402 | Package_TO_SOT_SMD:SOT-23 | Q5 |
| 1 | NJM2884 | Package_TO_SOT_SMD:SOT-89-5_Handsoldering | U5 |
| 1 | RESET_SW | SamacSys:SKRPABE010 | SW1 |
| 1 | SG-210STF | Oscillator:Oscillator_SMD_SeikoEpson_SG210-4Pin_2.5x2.0mm | X1 |
| 1 | SSSS810701 | SamacSys:SSSS810701 | U6 |
| 1 | STM32F412CGUx | Package_DFN_QFN:QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U9 |
| 1 | SWD | Connector_PinSocket_1.27mm:PinSocket_1x06_P1.27mm_Vertical | J5 |
| 1 | UART | Connector_PinSocket_1.27mm:PinSocket_1x04_P1.27mm_Vertical | J6 |
Questions
How big is the SaponseEx PCB?
It measures 92.9 × 54.5 mm and has 2 copper layers, 0.8 mm thick.
What parts does the SaponseEx use?
91 parts, built around the AS5047P-ATSM, ICM-20648, SSSS810701 and BSS138. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the SaponseEx KiCad files?
From the hide4096/SaponseEx repository on GitHub, at the commit this page was made from: the board is PCB/SaponseEx.kicad_pcb and its schematic PCB/SaponseEx.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the SaponseEx design in my own project?
Its repository states no licence, so its author keeps all rights: ask hide4096 before reusing the design.
Similar boards
- 2 layers47.4 × 64 mm
TORANEKO.Mk3
Tokoro0917/ToraNeko.Mk3
KiCadプロジェクト本体（TORANEKO.Mk3.kicadpro / .kicadsch / .kicadpcb）を作成済みです（現状は空、これから回路図を起こしていきます）。 このディレクトリには、実際に回路図を起こす前に固めておいた機能ブロック構成・ペリフェラル割り当て案・BOMドラフトも一緒に置いています。
93 parts1MIT - 2 layers103 × 50 mm
- 4 layers112 × 57 mm
- 2 layers31.5 × 50.5 mm
- 4 layers50 × 16 mm
System board
proegssilb/lightsaber-hardware
PCBs and other files for lightsaber soundboard hardware.
72 parts2CERN-OHL-S-2.0 - 2 layers110.8 × 117 mm
- 4 layers43 × 29 mm
