

We755a slc
WE 755A PBX Station Line Concentrator
- Size
- 88.9 × 79.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 57
- Nets
- 86
- Pads
- 247
- Tracks, vias
- 891, 21
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 2 Jun 2024
- Updated
- 8 Dec 2025
Overview
We755a slc is an open-source printed circuit board by hharte, from the hharte/we755a_slc repository on GitHub, published under the MIT licence. It is a 2-layer board of 88.9 × 79.8 mm with 57 parts on 86 nets, routed with 891 tracks and 21 vias.
It is built around the AVR128DA28-E/SP, SN65HVD3082EP and DPBW06F-05, with the LAA108, LTV-844 and CFM12JT10K0 among its other parts. Its parts include 13 resistors, 9 ICs, 8 capacitors, 6 connectors and 5 diodes.
Main components
12AVR128DA28-E/SP
SPDIP-28-40℃~+125℃ 1.8V~5.5V 10bit 128KB 12bit 16KB 23 24MHz 512Byte 8 Bit AVR Built-in FLASH SPDIP-28 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)SN65HVD3082EP
DIP-8-40℃~+85℃ 1 1 200Kbps 256 4.5V~5.5V 425uA Half-Duplex Transceiver ±15kV DIP-8 RS-485 / RS-422 ICs ROHSTexas InstrumentsRS-485 / RS-422 ICsDPBW06F-05
-- Power Module/Power Supply ROHSMWPower Supply Module,Power SuppliesLAA108
DIP-8Solid State Relays (Triac Output)Littelfuse/IXYSLTV-844
DIP-16-30℃~+100℃ 1.2V 100mV@20mA,1mA 20% 200mW 300% 35V 3us 4 4us 50mA 50mA 5kV AC,DC Phototransistor DIP-16 Transistor, Photovoltaic Output Optoisolators ROHSLite-OnTransistor, Photovoltaic Output OptoisolatorsCFM12JT10K0
插件,D2.3xL6.5mm-500ppm/℃~0ppm/℃ -55℃~+155℃ 10kΩ 500mW Carbon Film Resistor ±5% 插件,D2.3xL6.5mm Through Hole Resistors ROHSStackpole Electronics (SEI)Through Hole ResistorsK104M15X7RF5TL2
插件,P=2.5mm100nF 2.5mm 50V X7R ±20% Plugin,P=2.5mm Multilayer Ceramic Capacitors MLCC - Leaded ROHSVishay IntertechnologyMultilayer Ceramic Capacitors MLCC - LeadedCFM12JT120R
插件,D2.3xL6.5mm-400ppm/℃~0ppm/℃ -55℃~+155℃ 120Ω 500mW Carbon Film Resistor ±5% 插件,D2.3xL6.5mm Through Hole Resistors ROHSStackpole Electronics (SEI)Through Hole Resistors1N4007-E3/73
DO-204AL-50℃~+150℃ 1 Independent 1.1V@1A 1A 1kV 45A 5uA@1kV DO-204AL Diodes - General Purpose ROHSVishay IntertechnologyDiodes - General PurposeCFM12JT22K0
插件,D2.3xL6.5mm-500ppm/℃~0ppm/℃ -55℃~+155℃ 22kΩ 500mW Carbon Film Resistor ±5% 插件,D2.3xL6.5mm Through Hole Resistors ROHSStackpole Electronics (SEI)Through Hole ResistorsRXEF025
插件,P=5.1mm-40℃~+85℃ 1.25Ω 2.5s 250mA 3Ω 40A 410mW 500mA 72V Plugin,P=5.1mm Resettable Fuses ROHSLittelfuseResettable FusesWP934CB/ID
插件,P=2.54mm-40℃~+85℃ 1.9V 10mA 2.9mm Round Lens 50mcd 50° 617nm 627nm 75mW Frosted Red Lens Red 插件,P=2.54mm LED Indication - Discrete ROHSKingbrightLED Indication - Discrete
README
README.mdWE 755A PBX Station Line Concentrator
Introduction
The Western Electric 755A PBX station set with line lamps requires 15 wires between the station set and the PBX. This project is a concentrator that cuts down the requirement to 4 pairs (8 wires) so a standard 4-pair CAT6 cable can be used per station.
Here is an introductory video of the 755A PBX in operation.
Overview of Operation
The board contains a microcontroller, six solid-state relays, and six opto-isolated inputs. Boards are assembled in either the PBX-End Concentrator or the STA-End Concentrator configuration. The PBX-End Concentrator connects to the 755A PBX station line, and the STA-End Concentrator connects to the station set. These two boards are connected by six wires: -24VDC, GRD, Tip, Ring, and RS-485 A and B. They communicate with each other digitally via RS-485.

Station Loop
The station Tip and Ring are passed untouched between the 755A PBX and Station (STA) Set.
Communication
The PBX-End and STA-End concentrators communicate with each other using a half-duplex RS-485 link. The RS-485 link’s A and B lines are pulled up/down at the PBX-End Concentrator. The RS-485 link is terminated via 120-ohm resistors at both ends.
Buttons
The STA-End Concentrator monitors the six buttons (Hold, TRK1-4, Local) using opto-isolated inputs. The microcontroller encodes the button state and sends it to the PBX-End Concentrator. The PBX-End concentrator converts the button presses received into solid-state relay outputs to control H, TRK1-4, and Local.
Lamps
The PBX-End concentrator monitors the five lamp outputs (TRK1-4_L1, LOCAL_L1) and the state of the G lead from the PBX using opto-isolated inputs. The microcontroller encodes the lamp and G lead state and sends it to the STA-End Concentrator. The STA-End Concentrator converts the lamp and G states into solid-state relay outputs to control TRK1-4_L1 outputs to light the station lamps. The lamp ground is -5VDC while the TRK1-4_L1 outputs are +5V to provide 10VDC to each lamp.
Status
The boards have been assembled and are working as intended.

PCB Assembly
Bill of Materials
The same bare PCB is used for the PBX-End and Station-End concentrator. A pair (PBX-End and Station-End) are needed for each station set attached to the 755A PBX. The bare PCB is assembled differently, depending on whether it will be used as the PBX-End or Station-End.
Online DigiKey BOM. Interactive BOM.
PBX-End Concentrator
- Use +5VDC DC-DC converter SPBW06G-05 for PS1.
- Use a 1.5K-ohm resistor network for RN2.
- Populate R1 (10K.)
- Install RS-485 pull-up/down resistors at R3, R4.
- Install RS-485 terminator at R2.
- Install jumpers on pins 2-3 of JP1, JP4.
- Populate D1
- Populate F1: J1-1 is the -24VDC power input from the PBX power supply.
- Populate, F2.
- Populate U8, R12, and J5 if using the WE 755A PBX Monitor board.
Station-End Concentrator
- Use +/-5VDC DC-DC converter DPBW06F-05 for PS1.
- Use a 220-ohm resistor network for RN2.
- Do not populate R1 (10K.)
- Install RS-485 terminator at R2.
- Install jumpers on pins 1-2 of JP1, JP4.
- Do not populate D1.
- Do not populate F1, instead, install a wire between the F1 pad closest to the “LG” marking on the silkscreen and the pad in the center of the F1 footprint. J1-1 is “LG” and provides -5VDC so the 51A lamps in the station set are lit with 10VDC for proper brightness.
- Install a wire in place of F2. J1-2 is connected to the “G” lead on the station set.
- For Local ring detect, populate: C3, R2, R3, R7, R9, C8, D2.
Connections
755A PBX Line Connections to PBX-End Concentrator
12-pair inside wiring color code between the 755A PBX Station Line and the PBX-End Concentrator. This color coding is chosen to match the order of the terminals on the 66-blocks connected to the 755A PBX.
| 12 Pair IW Color | SLC Terminal J1 | Description | Microcontroller |
| BL-BK (Red) | J1-1 | -24VDC (-BATT) | - |
| BK-BL (Black) | J1-2 | GRD | - |
| W-OR | J1-3 | TK1 | SSR Output (PD0) |
| OR-W | J1-4 | TK2 | SSR Output (PD1) |
| W-GR | J1-5 | TK3 | SSR Output (PD2) |
| GR-WH | J1-6 | TK4 | SSR Output (PD3) |
| BR-WH | J1-7 | Local | SSR Output (PD4) |
| WH-S | J1-8 | H | SSR Output (H) |
| 12 Pair IW Color | SLC Terminal J2 | Description | Microcontroller |
| W-BL | J2-1 | Tip | - |
| BL-W | J2-2 | Ring | - |
| WH-BR | J2-3 | G | Input (PA7) |
| BL-R | J2-4 | TK1 L1 | Input (PA0) |
| OR-R | J2-5 | TK2 L1 | Input (PA1) |
| G-R | J2-6 | TK3 L1 | Input (PA2) |
| BR-R | J2-7 | TK4 L1 | Input (PA3) |
| S-R | J2-8 | LOC L1 | Input (PA6) |
466A Station Set Connections to STA-End Concentrator
| 466A Terminal | D15A (Cloth) Color | D15D (Vinyl) Color | SLC Terminal | Description | Microcontroller |
| LG | BR-G | S-BK | J1-1 | Lamp Ground (-5VDC) | - |
| RR | BR-R | BR-G | J1-2 | G | GND |
| 1L | BR-BK | S-Y | J1-3 | TK1 L1 | SSR Output (PD0) |
| 2L | BR-W | S-BL | J1-4 | TK2 L1 | SSR Output (PD1) |
| 3L | R-G | S-W | J1-5 | TK3 L1 | SSR Output (PD2) |
| 4L | R-Y | S-BR | J1-6 | TK4 L1 | SSR Output (PD3) |
| 5L | R-BK | BR | J1-7 | LOC L1 | SSR Output (PD4) |
| J1-8 | Not used | SSR Output (H) | |||
| 466A Terminal | D15A (Cloth) Color | D15D (Vinyl) Color | SLC Terminal | Description | Microcontroller |
| L2Y | G (Yellow*) | Green | J2-1 | Tip | - |
| L1 | R | Red | J2-2 | Ring | - |
| GN | Y (Green*) | BR-BK | J2-3 | H | Input (PA7) |
| YY | BR-Y | BK | J2-4 | TK1 | Input (PA0) |
| W | W | Y | J2-5 | TK2 | Input (PA1) |
| BB | BR-BL | W | J2-6 | TK3 | Input (PA2) |
| BK | BK | BL | J2-7 | TK4 | Input (PA3) |
| BL | BL | BR-R | J2-8 | Local | Input (PA6) |
- Colors as described in BSP (As found in 466AC-3 set dated 7-49).
Connections Between PBX and STA Concentrators
| RJ-45 Pair (T-568A) | Description |
| W-BL | Tip |
| BL | Ring |
| W-OR | RS-485 A |
| OR | RS-485 B |
| W-GR | Spare (available for other uses) |
| GR | Spare (available for other uses) |
| W-BR | -24VDC |
| BR | GRD |
RS-485
AVR128DA28 Datasheet
DxCore RS-485 link.
The low-level protocol used over the RS-485 link borrows from the protocol used in the Nortel Millennium payphone.
Technical Details
Microcontroller Firmware
The microcontroller firmware uses the Arduino development environment with the DxCore library for ease of development. Both the STA-End and PBX-End concentrators use the same firmware. The firmware determines whether it is operating in STA-mode or PBX-mode by reading the PF1 GPIO pin. The state of the FP1 pin is controlled by the JP1 jumper, and is “1” (+5VDC) for STA-mode, and “0” (GND) for PBX-mode.
The firmware provides a command-line interface via the serial port (J3.) The command line interface is the same for both STA-End and PBX-End. The only difference is that commands for controlling lamps on the STA-End control the SSRs on the STA-End concentrator directly, while the same commands on the PBX-End send a message over the RS-485 interface to the STA-End to perform the operation. Other commands, such as selecting lines are executed locally on the PBX-End, while the same command issued from the STA-End sends a message over the RS-485 interface to the PBX-End to perform the command.
Microcontroller Programming
The AVR128DA28 microcontroller is programmed using the UPDI / UART interface at J3. To enable UPDI programming, install a jumper at JP2.
The 6-pin header at J3 is compatible with a a USB to 5V TTL Serial cable for console access only or a Rocket Scream UPDI-USB-Serial Adapter V2 which provides for UPDI programming as well as a dedicated USB serial port for the console. To program the microcontroller, select "jtag2updi" as the programmer type in the Arduino IDE.
Instead of the Rocket Scream adapter, you can use the Adafruit UPDI Friend: set to 5V, and connect the UPDI and GND pins to the concentrator board. Select "Serial UPDI" as the programmer type in the Arduino IDE.
Arduino AVD128DA28 Configuration

Future Improvements
- There are spare RS-485 transceivers on the board. These are intended to be used in the future to on the PBX-End Concentrator to receive per-line “hold” information from the 755A PBX. This would allow for inclusion of winking line lamps for held PBX lines, similar to 1A1/1A2 key systems.
- In theory, it is possible to superimpose the RS-485 A and B signaling over the power wires, reducing the pair count to two. For simplicity, this has not been attempted for the current project.
Other WE 755A Projects
Parts
57| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R5, R6, R8, R10 |
| 4 | 0.1uF | Capacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mm | C1, C5, C6, C7 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3_Pad | H2, H3, H4, H5 |
| 3 | 120 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4, R11, R12 |
| 3 | LAA108 | Package_DIP:DIP-8_W7.62mm | U4, U6, U7 |
| 3 | THVD1420D | Package_DIP:DIP-8_W7.62mm | U3, U8, U9 |
| 2 | 1N4007 | Diode_THT:D_DO-41_SOD81_P7.62mm_Horizontal | D1, D2 |
| 2 | 22K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R3 |
| 2 | Jumper_2_Open | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP2, JP3 |
| 2 | Jumper_3_Open | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1, JP4 |
| 2 | LTV-844 | Package_DIP:DIP-16_W7.62mm | U2, U5 |
| 2 | Polyfuse | ac125a_dtmf:FUSE_RXEF025_LTF | F1, F2 |
| 2 | RED LED | ac125a_dtmf:LED_WP934CB&slash_GD_KNB | D4, D5 |
| 2 | Screw_Terminal_01x08 | ac125a_dtmf:Buchanan_4DB-8 | J1, J2 |
| 1 | -5V | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | TP1 |
| 1 | 0.01uF | Capacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mm | C4 |
| 1 | 0.1uF/630V | Capacitor_THT:C_Disc_D7.5mm_W5.0mm_P5.00mm | C3 |
| 1 | 100K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R9 |
| 1 | 10uf / 10V | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mm | C2 |
| 1 | 1M | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R7 |
| 1 | 220 | Resistor_THT:R_Array_SIP10 | RN1 |
| 1 | 220 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R13 |
| 1 | 220 (STA) or 1.5K (PBX) | Resistor_THT:R_Array_SIP10 | RN2 |
| 1 | 4.7uF | Capacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mm | C8 |
| 1 | AVR128DA28-I/SS | Package_DIP:DIP-28_W7.62mm_Socket | U1 |
| 1 | CONC_CABLE | Connector_RJ:RJ45_Amphenol_54602-x08_Horizontal | J4 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | Conn_01x04 | ac125a_dtmf:70543-0003_MOL | J5 |
| 1 | Conn_01x06_Male | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Horizontal | J3 |
| 1 | DPBW06F-05 | Converter_DCDC:Converter_DCDC_TRACO_TMR4-xxxxWI_THT | PS1 |
| 1 | GRD_TIE | Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm | JP5 |
| 1 | GREEN LED | ac125a_dtmf:LED_WP934CB&slash_GD_KNB | D3 |
| 1 | MountingHole | MountingHole:MountingHole_5.3mm_M5 | H1 |
Similar boards
- 2 layers158.8 × 159.8 mm

- 2 layers49 × 82.3 mm

- 2 layers65 × 56 mm

Rpi simplex clock hat
hharte/rpi-simplex-clock-hat
Raspberry Pi Hat to control a Simplex synchronous clock.
26 parts1MIT - 2 layers100 × 100 mm

Four Channel MHz LED Driver
Llamero/Four_Channel_MHz_LED_Driver
High Speed Four Channel LED Driver that can run up to 30A
96 parts6 - 4 layers56.6 × 82.7 mm

- 2 layers59.2 × 52.9 mm

- 2 layers100 × 70.3 mm

- 2 layers165.1 × 120.7 mm

Questions
How big is the We755a slc PCB?
It measures 88.9 × 79.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the We755a slc use?
57 parts, built around the AVR128DA28-E/SP, SN65HVD3082EP, DPBW06F-05 and LAA108. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the We755a slc KiCad files?
From the hharte/we755a_slc repository on GitHub, at the commit this page was made from: the board is hardware/we755a_slc.kicad_pcb and its schematic hardware/we755a_slc.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the We755a slc design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).