

We755a dtmf
DTMF Converter for the WE 755A PBX
- Size
- 49 × 82.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 52
- Nets
- 82
- Pads
- 219
- Tracks, vias
- 633, 10
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 5 Jun 2023
- Updated
- 30 Nov 2024
Overview
We755a dtmf is an open-source printed circuit board by hharte, from the hharte/we755a_dtmf repository on GitHub, published under the MIT licence. It is a 2-layer board of 49 × 82.3 mm with 52 parts on 82 nets, routed with 633 tracks and 10 vias.
It is built around the AVR128DA28-E/SP, SPBW06G-05 and MT8870DS1, with the LAA108, H11AA1 and K104M15X7RF5TL2 among its other parts. Its parts include 14 resistors, 8 capacitors, 8 ICs, 4 diodes and 2 connectors.
Main components
12AVR128DA28-E/SP
SPDIP-28-40℃~+125℃ 1.8V~5.5V 10bit 128KB 12bit 16KB 23 24MHz 512Byte 8 Bit AVR Built-in FLASH SPDIP-28 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)SPBW06G-05
SIP,21.8x9.2mmSIP,21.8x9.2mm Power Module/Power Supply ROHSMWPower Module/Power SupplyMT8870DS1
SOIC-18-300mil-40℃~+85℃ 15mW 4.75V~5.25V 9mA SOIC-18-300mil Telecom Interface ICs ROHSMicrochip TechnologyTelecommunication Interface ICsLAA108
DIP-8Solid State Relays (Triac Output)Littelfuse/IXYSH11AA1
DIP-6-55℃~+100℃ 1.2V 20% 30V 400mV@10mA,0.5mA 5.3kV 60mA AC,DC Integrated anti-parallel LED Phototransistor DIP-6 Transistor, Photovoltaic Output Optoisolators ROHSVishay IntertechnologyTransistor, Photovoltaic Output OptoisolatorsK104M15X7RF5TL2
插件,P=2.5mm100nF 2.5mm 50V X7R ±20% Plugin,P=2.5mm Multilayer Ceramic Capacitors MLCC - Leaded ROHSVishay IntertechnologyMultilayer Ceramic Capacitors MLCC - LeadedMFR-25FBF52-110K
插件,D2.4xL6.3mm-55℃~+155℃ 110kΩ 250mW Metal Film Resistor ±1% ±100ppm/℃ 插件,D2.4xL6.3mm Through Hole Resistors ROHSYAGEOThrough Hole ResistorsRDER72J103K2K1H03B
插件,P=5mm10nF 5mm 630V X7R ±10% Plugin,P=5mm Multilayer Ceramic Capacitors MLCC - Leaded ROHSMurataMultilayer Ceramic Capacitors MLCC - Leaded1N4734A-T50A
插件,D2.03xL4.06mm-65℃~+200℃ 1 Independent 10uA@2V 1W 5.32V~5.88V 5.6V 5Ω 600Ω Plugin,D2.03xL4.06mm Zener Diodes ROHSonsemiZener DiodesRXEF025
插件,P=5.1mm-40℃~+85℃ 1.25Ω 2.5s 250mA 3Ω 40A 410mW 500mA 72V Plugin,P=5.1mm Resettable Fuses ROHSLittelfuseResettable FusesK103K15X7RF5UL2
插件,P=2.5mm10nF 2.5mm 50V X7R ±10% Plugin,P=2.5mm Multilayer Ceramic Capacitors MLCC - Leaded ROHSVishay IntertechnologyMultilayer Ceramic Capacitors MLCC - LeadedCFM12JT1K50
插件,D2.3xL6.5mm-400ppm/℃~0ppm/℃ -55℃~+155℃ 1.5kΩ 500mW Carbon Film Resistor ±5% 插件,D2.3xL6.5mm Through Hole Resistors ROHSStackpole Electronics (SEI)Through Hole Resistors
README
README.mdWE 755A PBX DTMF Converter
Introduction
The Western Electric 755A PBX was designed in 1938 and supports pulse dialing only This DTMF converter adds support for Touch-Tone dialing. One DTMF Converter board needs to be installed in each of the three links. The converter recognizes DTMF digits, and sets the pulse counting relays in the link to the terminal count for the number dialed. This is not a tone to pulse converter, and operates much faster than one.
The dial plan for the 755A PBX consists of local station extensions 20-29 and 30-39. Although this PBX supports four trunks, they are not directly accessible by stations; instead, key stations with individual trunk pickup keys are used to select the trunks.
Here is an introductory video of the 755A PBX in operation.
This project builds upon the OKI AC125A DTMF Converter designed several years ago. While the OKI is an electromechanical crossbar PBX similar in some ways to the 755A, the OKI is about 40 years more modern.
Status
Three boards have been assembled and installed in each of the 755A’s links. They work as intended for station to station and conference calls.



Translation
The DTMF converter employs digit translation as follows:
| First Dialed Digit | 755A Extension | Description |
| 0 | 20 | Operator |
| 1 | - | No operation |
| 2 | 2x | Direct-dialed 755A stations. |
| 3 | 3x | Direct-dialed 755A stations. |
| 4, 5, 6, 7 | - | No operation |
| 8 | 26 | Ringdown extensions 26, 27. |
| 9 | 36 | Ringdown extensions 36, 37 |
755A PBX Connector
| Pin | Description | Ribbon Cable Color | Cloth Wire Color | 755A Link Connection |
| 1,2 | GRD | Brown/Red | Black | Connect to the B relay coil so the converter powers up when the link is active. |
| 3 | LINK_SPARE | Orange | ||
| 4 | LINK_C1 | Yellow | Or/Sl | |
| 5 | LINK_6 | Green | Sl/W/R | |
| 6 | LINK_5-6 | Blue | SL/W | |
| 7 | LINK_4-0 | Violet | Br/R | |
| 8 | LINK_3-9 | Slate | Br | |
| 9 | LINK_2-8 | White | Gr/R | |
| 10 | LINK_1-7 | Black | Gr | |
| 11 | LINK_T3 | Brown | Or/R | |
| 12 | LINK_T2 | Red | Or | |
| 13 | N/C | Orange | ||
| 14 | N/C | Yellow | ||
| 15 | N/C | Green | ||
| 16 | LINK_E | Blue | Blue | |
| 17 | Tip | Violet | O/GR | |
| 18 | Ring | Slate | O/GR-R | |
| 19,20 | -24VDC | White/Black | Red | -24VDC (Red) |
Connection Notes
From SD-66611-01:
-BAT: Pick up from P1 relay red lead.
GRD: Pick up from B relay coil.
LINK_B: (Blue) Pick up from B relay coil (Upper left terminal.)
Tip: (Violet): Pick up T from 2mF capacitors on lower right corner (looking at from rear):
Ring: (Slate): Pick up T from 2mF capacitors on lower right corner (looking at from rear):

LINK_T2: (Red) Pick up from T2 relay coil.
LINK_T3: (Brown) Pick up from T3 relay coil.
LINK_C1: (Yellow) Pick up from C1 relay coil.
Technical Details
Theory of Operation
The 755A DTMF converter’s ground supply is connected to the B relay coil in the link so that the DTMF converter is only powered on when the link is active. This is necessary so that the first and second digits dialed can be properly identified if the calling station hangs up after dialing only a single digit.
When a station goes off hook, the link allotter selects an idle link, operating the link’s B relay. This powers up the DTMF converter, which waits for digit(s) to be dialed. If the first dialed digit is 2 or 3, the converter waits for a second digit to be dialed and then activates the tens and units counting relays to their terminal count. If the first digit is a digit other than 2 or 3 is dialed, the digit is handled as follows:
- 1, 4, 5, 6, or 7: Ignored
- 0, 8, 9: Translated to a 2-digit extension that is dialed immediately.
After dialing is complete, further dialing is disabled until the called station answers and hangs up again. This is needed to prevent operation of the pulse counting relays during an established call, while also supporting conference calling.
Conference calling with the 755A works as follows:
- The originating station calls an extension.
- The extension answers the call, activating the E relay.
- The originating station asks the answering station to hang up momentarily so that a conference call can be established.
- After the called station hangs up, the originating station dials the number of an additional station to join the conference.
- After the first digit of the called number is dialed,
Pulse Dialing Terminal Count Relays
Tens Digit (2 or 3)
| Digit | Relays Activated | Note |
| 2 | T2 | T2 activated stops dialtone. |
| 3 | T2 and T3 |
Units Digit (0-9)
| Digit | Relays Activated | To finish dialing |
| 1 | C1, 1-7 | Release C1 |
| 2 | C1, 2-8 | Release C1 |
| 3 | C1, 3-9 | Release C1 |
| 4 | C1, 4-0 | Release C1 |
| 5 | C1, 5-6 | Release C1 |
| 6 | C1, 5-6, 6 | Release C1 |
| 7 | C1, 1-7, 6 | Release C1 |
| 8 | C1, 2-8, 6 | Release C1 |
| 9 | C1, 3-9, 6 | Release C1 |
| 0 | C1, 4-0, 6 | Release C1 |
Inputs from 755A
| T | Tip | ||
| R | Ring | ||
| E | Call Active (Interrupt the microcontroller.) | ||
Outputs to 755A
| T2 | Tens Digit 2 (Breaks dial tone.) | ||
| T3 | Tens Digit 3 (Also requires T2 activated.) | ||
| 1-7, 2-8, 3-9, 4-0, 5-6, 6 | Units Digit Selection | ||
| C1 | Activated before Units selection relays are set, released when the digit is complete. | ||
MT8870 DTMF Converter Outputs
| Q3:0 | DTMF Digit Selection | ||
| StB | DTMF Valid Strobe (Interrupt to microcontroller.) | ||
Bill of Materials
Online DigiKey BOM. Interactive BOM.
| Quantity | Reference Designator | Value |
| 4 | C1, C2, C4, C7 | 0.1uF |
| 1 | C3 | 0.01uF |
| 2 | C5, C8 | 0.01uF/630V |
| 1 | C6 | 10uF 25V |
| 1 | D1 | 1N4148 |
| 1 | D2 | LED |
| 2 | D3, D4 | 1N4734A |
| 2 | F1, F2 | Fuse 630mA |
| 2 | H1, H2 | MountingHole |
| 1 | J1 | Conn_01x06_Male right angle |
| 1 | J2 | UPDI (2x3 pin header) Straight |
| 1 | J3 | Conn_02x10_Odd_Even |
| 1 | PS1 | SPBW06 |
| 1 | R1 | 100K |
| 1 | R2 | 330K |
| 1 | R3 | 220 |
| 1 | R4 | 52.3K 1% |
| 4 | R5, R6, R8, R12 | 110K 1% |
| 1 | R7 | 4.7K |
| 1 | R9 | 220K 1% |
| 1 | R10 | 10K |
| 1 | R11 | 68.1K 1% |
| 1 | R13 | 1.5K |
| 1 | RN1 | 220 |
| 1 | U1 | AVR128DA28-I/SP or AVR128DA28-E/SP |
| 1 | U2 | MT8870 |
| 1 | U3 | H11AA1 |
| 5 | U4, U5, U6, U7, U8 | LAA108 (or LAA110L or CLA170) |
| 1 | Y2 | 3.579545MHZ |
Arduino AVD128DA28 Configuration

Other WE 755A Projects
Parts
52| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | LAA108 | Package_DIP:DIP-8_W7.62mm | U4, U5, U6, U7, U8 |
| 4 | 0.1uF | Capacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mm | C1, C2, C4, C7 |
| 4 | 110K 1% | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5, R6, R8, R12 |
| 2 | 0.01uF/630V | Capacitor_THT:C_Disc_D7.5mm_W5.0mm_P5.00mm | C5, C8 |
| 2 | 1N4734A | Diode_THT:D_DO-41_SOD81_P7.62mm_Horizontal | D3, D4 |
| 2 | 5V_J3 | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP9, JP10 |
| 2 | Jumper_2_Open | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP1, JP2 |
| 2 | Polyfuse | ac125a_dtmf:FUSE_RXEF025_LTF | F1, F2 |
| 1 | 0.01uF | Capacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mm | C3 |
| 1 | 1.5K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R13 |
| 1 | 100K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R10 |
| 1 | 10uf / 10V | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mm | C6 |
| 1 | 120 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R14 |
| 1 | 1N4148 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D1 |
| 1 | 220 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3 |
| 1 | 220 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R7 |
| 1 | 220K 1% | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R9 |
| 1 | 3.579545MHZ | Crystal:Crystal_HC49-U_Vertical | Y2 |
| 1 | 32.767KHz | Crystal:Crystal_Round_D2.0mm_Vertical | Y1 |
| 1 | 330K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
| 1 | 52.3K 1% | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
| 1 | 68.1K 1% | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R11 |
| 1 | AVR128DA28-I/SS | Package_DIP:DIP-28_W7.62mm_Socket | U1 |
| 1 | Conn_01x06_Male | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Horizontal | J1 |
| 1 | Conn_02x10_Odd_Even | ac125a_dtmf:WE755A-DTMF | J3 |
| 1 | GND_J3 | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP8 |
| 1 | GRD_TIE | Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm | JP3 |
| 1 | G_SSR_GNDPWR | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP5 |
| 1 | H11AA1 | Package_DIP:DIP-6_W7.62mm | U3 |
| 1 | LED | LED_THT:LED_D5.0mm | D2 |
| 1 | LINK6_G_SSR | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP4 |
| 1 | LINK6_TIP | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP7 |
| 1 | MT8870 | Package_DIP:DIP-18_W7.62mm | U2 |
| 1 | R_Network10_220R | Resistor_THT:R_Array_SIP11 | RN1 |
| 1 | SPBW06-5 | Converter_DCDC:Converter_DCDC_TRACO_TMR-xxxx_THT | PS1 |
| 1 | TIP_IN | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP6 |
Similar boards
- 2 layers158.8 × 159.8 mm

- 2 layers88.9 × 79.8 mm

- 2 layers69 × 28.5 mm

GR DTMF Decoder
GadgetReboot/DTMF_Decoder
MT8870 DTMF decoder for POTS phone line interfacing
15 parts9 - 2 layers65 × 56 mm

Rpi simplex clock hat
hharte/rpi-simplex-clock-hat
Raspberry Pi Hat to control a Simplex synchronous clock.
26 parts1MIT - 4 layers50 × 90 mm

- 2 layers41.4 × 47.5 mm

U2f zero panel
conorpp/u2f-zero
U2F USB token optimized for physical security, affordability, and style
52 parts2.4k - 2 layers136 × 130 mm

Lora nodemcu
sudomesh/disaster-radio
A (paused) work-in-progress long-range, low-bandwidth wireless disaster recovery mesh network powered by the sun.
52 parts1.1k - 2 layers69 × 53.8 mm

TUSS4470 shield
Neumi/open_echo
Open Source echo sounder / depth sounder / SONAR for bathymetry and research. Arduino based and compatible.
52 parts530
Questions
How big is the We755a dtmf PCB?
It measures 49 × 82.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the We755a dtmf use?
52 parts, built around the AVR128DA28-E/SP, SPBW06G-05, MT8870DS1 and LAA108. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the We755a dtmf KiCad files?
From the hharte/we755a_dtmf repository on GitHub, at the commit this page was made from: the board is hardware/we755a_dtmf.kicad_pcb and its schematic hardware/we755a_dtmf.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the We755a dtmf design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).