
Esp32-homeassistant rf bridge
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

Low cost, open source BLE device tracker | Compatible with macless-haystack
Beartag is an open-source printed circuit board by grimsteel, from the grimsteel/beartag repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 25.6 × 33.7 mm with 26 parts on 38 nets, routed with 199 tracks and 122 vias.
It is built around the CH571F, XC6206P332MR and 1N5819WS, with the AO3401A and P6SMB6.8CA/TR13 among its other parts. Its parts include 7 capacitors, 4 resistors, 3 diodes, 2 ICs and 2 switches. It belongs with the radio and wireless boards of this library.
A low cost, open source BLE device tracker.
Compatible with macless-haystack
The board is based on a WCH CH571 MCU. (Low cost BLE mcu)
It can be powered off of a single CR2032 battery, which should last at least a couple months (and potentially as long as a year)
The board includes one customizable button as well as a status LED.


Firmware is coming soon
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 5K1 | Resistor_SMD:R_0402_1005Metric | R1, R2, R3 |
| 2 | 1 uF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 10 uF | Capacitor_SMD:C_0603_1608Metric | C6, C7 |
| 2 | 2.2 uF | Capacitor_SMD:C_0402_1005Metric | C3, C5 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_XKB_TS-1187A | SW1, SW2 |
| 1 | 100 nF | Capacitor_SMD:C_0402_1005Metric | C4 |
| 1 | 100K | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 1N5819WS | Diode_SMD:D_SOD-323 | D1 |
| 1 | 22 uH | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | 32 MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 32.768 kHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y2 |
| 1 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Antenna_Chip | RF_Antenna:Texas_SWRA117D_2.4GHz_Right | AE1 |
| 1 | Battery_Cell | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | BT1 |
| 1 | CH571F | lcsc:QFN-28_L4.0-W4.0-P0.40-BL-EP2.7 | U1 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | P6SMB6.8CA/TR13 | Diode_SMD:D_SMB | D2 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23-3 | U2 |
| 1 | qrcode | lcsc:qrcode | QR***** |

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

Janky-Jingle-Crew/SouthPoleLevitator
2025 Christmas card "South Pole Levitator"

grimsteel/homeassistant-rf-bridge
MQTT-based Home Assistant RF + IR bridge

usr-ein/TriMixxx
Open source standalone DJ multimedia player, compatible with Rekordbox


garrettsworkshop/TimeDisk
Apple II memory expansion card with 1 MB battery-backed RAM and NoSlotClock-compatible clock


mupfdev/TrackMAG
An open hardware development board primarily intended for the development of accessible input devices.
It measures 25.6 × 33.7 mm and has 2 copper layers, 1.6 mm thick.
26 parts, built around the CH571F, XC6206P332MR, 1N5819WS and AO3401A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the grimsteel/beartag repository on GitHub, at the commit this page was made from: the board is pcb/beartag.kicad_pcb and its schematic pcb/beartag.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).