

Gladiolus
a Software Defined Infrared (SDIR) neighbor
- Size
- 70.7 × 53.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 159
- Nets
- 178
- Pads
- 562
- Tracks, vias
- 972, 102
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 27 May 2019
- Updated
- 6 Dec 2021
Overview
Gladiolus is an open-source printed circuit board by greatfet-hardware, from the greatfet-hardware/gladiolus repository on GitHub. It is a 2-layer board of 70.7 × 53.3 mm with 159 parts on 178 nets, routed with 972 tracks and 102 vias.
It is built around the AD8330ARQZ, LMH6643MM and THS4520RGT, with the 74LVC1G3157 and AD9283BRS among its other parts. Its parts include 70 resistors, 36 capacitors, 10 ICs, 10 inductors and 6 diodes.
Main components
5AD8330ARQZ
SSOP-16-150mil-40℃~+85℃ 1 150MHz 150V/us 2.7V~6V 20mA 20mA 20mA 2uV/℃ 50dB 60dB Analog voltage gain、Enable/shutdown function、Fully differential、Programmable reference voltage Differential Rail-to-rail output VGA SSOP-16-150mil Programmable / Variable Gain Amplifiers (PGA/VGA) ROHSAnalog DevicesProgrammable / Variable Gain Amplifiers (PGA/VGA)LMH6643MM
VSSOP-8-40℃~+85℃ 1.5uA 130MHz 130V/us 145mA 17nV/√Hz@100kHz 2 2.7V~12.8V 2.7mA 20nA 3.4mV 5uV/℃ 95dB Rail-to-rail output VSSOP-8 Operational Amplifier ROHSTexas InstrumentsOperational AmplifierTHS4520RGT
QFN16Wideband, Low Noise, Low Distortion Fully Differential Amplifier with Rail-to-Rail OutputTexas InstrumentsUncategorised74LVC1G3157
UncategorisedDiodes IncorporatedAD9283BRS
--40℃~+85℃ 0.5LSB 0.75LSB 2.7V~3.6V Parallel Port Pipeline Power-down mode、Built-in reference source - ADCs/DACs - Special Purpose ROHSAnalog DevicesADCs/DACs - Special Purpose
README
README.mdGladiolus
a GreatFET neighbor for Software Defined Infrared (SDIR)
Required KiCad dependency:
https://github.com/greatscottgadgets/gsg-kicad-lib
If you are using git, the preferred way to install gsg-kicad-lib is to use the submodule:
git submodule init && git submodule updateConcept
Gladiolus is an infrared (IR) transceiver in the style of Software Defined Radio (SDR), enabling implementation of arbitrary IR protocols. In every known over-the-air IR implementation, only the amplitude of the optical signal is modulated, so we detect/modulate the amplitude with a single ADC/DAC.
Example Targets
- 20 to 60 kHz IR remote control systems
- IrDA up to 4 Mbps
- Bosch Integrus audio broadcast over IR (DQPSK over AM)
- proximity sensors
Wavelength
Though many IR-over-fiber implementations use longer wavelengths, all over-the-air targets we've identified use wavelengths between 850 and 950 nm. Gladiolus detects and produces IR in that range.
Getting Started with Gladiolus
For receive, we have brought the signal into GNU Radio via a pipe. So:
mkfifo /tmp/fifo
greatfet_sdir -r -S 10200000 -f /tmp/fifoThat's going to capture at 10.2 MSps. In GNU Radio Companion connect a file source (pointed at /tmp/fifo with Byte type) through UChar to Float and into visualization blocks such as a QT GUI Time Sink or QT GUI Frequency Sink. If they're too strong or weak, the gain can be controlled by a DAC.
To replay a capture: greatfet_sdir -S 10200000 -f
If you want to transmit from a GRC flowgraph: greatfet_sdir -S 10200000 -f /tmp/fifo
AC or DC coupling
The receive photodiode is AC-coupled by default for immunity to ambient light such as sunlight, but it can be switched into DC-coupled mode.
photodiode
We use the Everlight PD204-6B through-hole photodiode (840-1100 nm). As an option, we have included pads for the Vishay VBPW34FASR (used in IRis) which has very high sensitivity due to large surface area but is somewhat slow.
DAC Bypass
Many applications use On-Off Keying (OOK), so the transmit DAC is not needed. It is possible to bypass the DAC and control the TX LED(s) with one pin.
Inspiration
http://onetransistor.blogspot.com/2014/12/infrared-protocol-analysis-with-pc.html
http://winlirc.sourceforge.net/
https://github.com/devttys0/IRis
http://www.analogzoo.com/2016/08/photodiode-amplifier-design/
http://defcon-wireless-village.com/speakers.html#blinded_by_the_light
http://dangerousprototypes.com/docs/USB_Infrared_Toy
http://www.grandideastudio.com/opticspy/
EVAL-CN0272-SDPZ is an interesting evaluation board with similar capabilities.
Parts
159| Qty | Value | Footprint | References |
|---|---|---|---|
| 19 | 100nF | gsg-modules:0603 | C3, C11, C12, C13, C17, C18, C19, C20, C21, C22, C23, C25, C27, C30, C31, C36 +3 |
| 18 | 0 | gsg-modules:0603 | R1, R2, R4, R20, R21, R23, R31, R38, R39, R40, R41, R42, R43, R44, R45, R67 +2 |
| 14 | 10k | gsg-modules:0603 | R10, R15, R16, R27, R36, R55, R58, R59, R60, R61, R62, R63, R64, R68 |
| 14 | TestPoint | gsg-modules:TESTPOINT-50MIL | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12, TP13, TP14 |
| 10 | 39 | gsg-modules:0603 | R28, R46, R47, R48, R49, R50, R51, R52, R53, R54 |
| 7 | R | gsg-modules:0603 | R5, R11, R12, R13, R14, R37, R56 |
| 6 | 2.2uH | gsg-modules:0402 | L1, L2, L5, L6, L7, L8 |
| 4 | 1k | gsg-modules:0603 | R17, R24, R25, R73 |
| 4 | 74LVC1G3157 | gsg-modules:SOT363 | U6, U7, U8, U10 |
| 4 | MOUNTING_HOLE | gsg-modules:HOLE126MIL-COPPER | MH1, MH2, MH3, MH4 |
| 3 | 10uF | gsg-modules:0805 | C8, C32, C35 |
| 3 | 15pF | gsg-modules:0402 | C2, C10, C26 |
| 3 | 330 | gsg-modules:0603 | R3, R9, R18 |
| 3 | LED | gsg-modules:0603D | D4, D5, D6 |
| 2 | 0 | gsg-modules:0402 | R32, R33 |
| 2 | 1.5uH | gsg-modules:0402 | L3, L4 |
| 2 | 100nF | gsg-modules:0402 | C24, C28 |
| 2 | 1nF | gsg-modules:0603 | C33, C34 |
| 2 | 1uH | gsg-modules:0402 | L9, L10 |
| 2 | 249 | gsg-modules:0603 | R66, R69 |
| 2 | C | gsg-modules:0603 | C1, C4 |
| 2 | Jumper_3_Bridged12 | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabels | JP1, JP2 |
| 2 | POT | gsg-modules:3306F | RV1, RV3 |
| 2 | R | gsg-modules:0402 | R34, R35 |
| 1 | 1.74k | gsg-modules:0603 | R8 |
| 1 | 1.80k | gsg-modules:0603 | R70 |
| 1 | 100k | gsg-modules:0402 | R6 |
| 1 | 100pF | gsg-modules:0402 | C9 |
| 1 | 12k | gsg-modules:0603 | R65 |
| 1 | 130pF | gsg-modules:0402 | C14 |
| 1 | 20k | gsg-modules:0603 | R57 |
| 1 | 24pF | gsg-modules:0402 | C16 |
| 1 | 3.24k | gsg-modules:0603 | R7 |
| 1 | 470pF | gsg-modules:0402 | C29 |
| 1 | 75 | gsg-modules:0603 | R30 |
| 1 | 82pF | gsg-modules:0402 | C15 |
| 1 | 953 | gsg-modules:0603 | R71 |
| 1 | AD8330ARQZ | gsg-modules:TSSOP16 | U2 |
| 1 | AD9283 | gsg-modules:SSOP20 | U3 |
| 1 | AD9704 | gsg-modules:QFN32-5 | U4 |
| 1 | BONUS_ROW | gsg-modules:HEADER-1x20 | J7 |
| 1 | FILTER | gsg-modules:0805 | FB1 |
| 1 | LED | LEDs:LED-5MM | D3 |
| 1 | LMH6643 | gsg-modules:VSSOP8 | U5 |
| 1 | MCP4706 | Package_TO_SOT_SMD:SOT-23-6 | U9 |
| 1 | NEIGHBOR1 | gsg-modules:HEADER-2x20 | J1 |
| 1 | NEIGHBOR2 | gsg-modules:HEADER-2x20 | J2 |
| 1 | PHOTODIODE | LEDs:LED-3MM | D1 |
| 1 | PHOTODIODE | gsg-modules:VBPW34FASR | D2 |
| 1 | Q_NPN_BEC | gsg-modules:SOT23-3 | Q1 |
| 1 | THS4520RGT | gsg-modules:QFN16-3 | U1 |
Similar boards
- 4 layers70.7 × 53.3 mm

- 4 layers100 × 100 mm

AFE
Blaze-Pascal/Masters-Multi-Channel_DAQ
Custom 2-channel digital oscilloscope DAQ with 20MHz bandwidth. Built with a custom KiCad analog front-end (AFE) PCB, Gowin FPGA (Tang Nano 9K) for high-speed signal buffering (VHDL), and an RPi Pico MCU for SCPI-like…
216 parts2GPL-3.0 - 4 layers50 × 100 mm

- 2 layers49.5 × 57.2 mm

- 4 layers130 × 105 mm

Vm101-inout
mirdej/vmix
Multichannel modular analog PAL video mixer based on the SYNKIE project
238 parts21 - 2 layers130 × 90 mm

- 2 layers100 × 62.1 mm

- 2 layers99 × 70.7 mm

Building blocks
mirdej/synkie
The Synkie is a modular open source analog video processor, developed by Michael Egger, Max Egger and Flo Kaufmann
165 parts47
Questions
How big is the Gladiolus PCB?
It measures 70.7 × 53.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Gladiolus use?
159 parts, built around the AD8330ARQZ, LMH6643MM, THS4520RGT and 74LVC1G3157. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Gladiolus KiCad files?
From the greatfet-hardware/gladiolus repository on GitHub, at the commit this page was made from: the board is gladiolus.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Gladiolus design in my own project?
Its repository states no licence, so its author keeps all rights: ask greatfet-hardware before reusing the design.