2 layers76 × 56 mm
2 layers68.6 × 53.3 mm
Arduino uno board
goodboy-kwame/Arduino-UnoSchematic, pcb, gerber file, bill of materials.
- Size
- 68.6 × 53.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 65
- Nets
- 121
- Pads
- 339
- Tracks, vias
- 208, 0
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 27 Jul 2026
- Updated
- 27 Jul 2026
Overview
Arduino uno board is an open-source printed circuit board by goodboy-kwame, from the goodboy-kwame/Arduino-Uno repository on GitHub. It is a 2-layer board of 68.6 × 53.3 mm with 65 parts on 121 nets, routed with 208 tracks and 0 vias.
It is built around the ATMEGA16U2-MU, ATMEGA328P-PU and LMV358, with the LP2985-33DBV and FDN340P among its other parts. Its parts include 17 resistors, 13 capacitors, 13 connectors, 7 diodes and 6 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
5
ATMEGA16U2-MU
QFN-32-EP(5x5)-40℃~+85℃ 16KB 16MHz 2.7V~5.5V 22 512Byte 512Byte 8 Bit AVR Built-in FLASH QFN-32-EP(5x5) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
ATMEGA328P-PU
DIP-28-300mil-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH DIP-28-300mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
LMV358
SOP-8-40℃~+125℃ 10pA 10pA 1MHz 2 2.5V~5.5V 20mA 20nV/√Hz@10kHz 2uV/℃ 40uA 5mV 600V/ms 65dB EMI filtering/RF suppression Rail-to-Rail Input, Rail-to-Rail Output SOP-8 Operational Amplifier ROHSTECH PUBLICOperational Amplifier
LP2985-33DBV
SOT-23-5-40℃~+125℃@(Tj) 1 150mA 16V 3.3V 30uVrms 45dB@(1kHz) 575mV@(150mA) 850uA Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Noise bypass terminal Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
FDN340P
SOT-23-55℃~+150℃ 1 P-Channel 1.5V 121pF 20V 2A 500mW 56pF 7.2nC@4.5V 70mΩ@4.5V 779pF P-Channel SOT-23 MOSFETs ROHSonsemiMOSFETs
Parts
65| Qty | Value | Footprint | References |
|---|---|---|---|
| 17 | R | Resistor_SMD:R_01005_0402Metric_Pad0.57x0.30mm_HandSolder | R1, R2, R3, R4, R5, R6, R7, R8, R10, R11, R12, R13, R14, R15, R16, R17 +1 |
| 8 | C | Capacitor_SMD:C_01005_0402Metric | C2, C3, C8, C10, C11, C12, C13, C14 |
| 4 | LED | LED_SMD:LED_0402_1005Metric | D1, D3, D4, D5 |
| 4 | MountingHole_3.2mm | Arduino_MountingHole:MountingHole_3.2mm | MH1, MH2, MH3, MH4 |
| 3 | C | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C6, C7, C9 |
| 2 | C_Polarized | Capacitor_SMD:CP_Elec_6.3x3 | C1, C4 |
| 2 | Conn_PIC_ICSP_ICD | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J6, J9 |
| 2 | D | Diode_SMD:D_01005_0402Metric | D2, D7 |
| 1 | ATmega16U2-M | Package_DFN_QFN:QFN-32-1EP_4x4mm_P0.4mm_EP2.9x2.9mm | U4 |
| 1 | ATmega328P-P | Package_DIP:DIP-28_W7.62mm | U5 |
| 1 | Analog | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Vertical | J3 |
| 1 | Barrel_Jack_Switch_Pin3Ring | Connector_BarrelJack:BarrelJack_Horizontal | J1 |
| 1 | Conn_01x06 | Connector_Hirose:Hirose_DF13-06P-1.25DSA_1x06_P1.25mm_Vertical | J8 |
| 1 | Conn_01x06_Pin | Connector_JST:JST_XH_B6B-XH-AM_1x06_P2.50mm_Vertical | J4 |
| 1 | Conn_01x08 | Connector_Hirose:Hirose_DF13-08P-1.25DSA_1x08_P1.25mm_Vertical | J3 |
| 1 | Conn_01x10 | Connector_Hirose:Hirose_DF13-10P-1.25DSA_1x10_P1.25mm_Vertical | J7 |
| 1 | Conn_02x03_Odd_Even | Connector_IDC:IDC-Header_2x06_P2.54mm_Latch_Vertical | J4 |
| 1 | Crystal | Crystal:Crystal_HC49-4H_Vertical | Y1 |
| 1 | D | Diode_SMD:D_0603_1608Metric | D6 |
| 1 | Digital/PWM | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J4 |
| 1 | Digital/PWM | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | J2 |
| 1 | FDN340P | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | LMV358 | Package_DFN_QFN:DFN-8-1EP_4x4mm_P0.8mm_EP2.5x3.6mm | U1 |
| 1 | LP2985-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | MIC2779L-xxM5 | Package_TO_SOT_SMD:SOT-23-5 | U6 |
| 1 | NCP1117-3.3_SOT223 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | Power | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J1 |
| 1 | SW_Push_Open_Dual | Button_Switch_THT:SW_PUSH_6mm | SW2 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_Pad1.0x1.5mm | JP2 |
| 1 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mm | JP1 |
| 1 | USB_C_Receptacle_PowerOnly_6P | Connector_USB:USB_C_Receptacle_GCT_USB4135-GF-A_6P_TopMnt_Horizontal | J5 |
Similar boards
- 2 layers96.9 × 75.4 mm
PRINCE EMMANUEL ADRUINO 01235059B
izunduprince1-design/ARDRUINO-UNO-BOARD
ARDRUINO UNO BUILT PCB BORD
60 parts - 2 layers56.6 × 62.2 mm
ArduinoR3
Morethanmany2/Arduino-Uno
As a part of my day-to-day use, i tried to design the Arduino UNO dev board using all the datasheet materials and footprints required for precise design.
59 parts - 2 layers95.3 × 70.8 mm
ARDUINO UNO
Nakoja-Silas/ARDUINO-UNO
The board can be tested using a simple LED Blink program.
60 parts - 2 layers97 × 75.5 mm
Arduino Uno R3
SuganyaBaskaran/kicad-projects
Portfolio, learning and practice attempts using KiCAD.
56 parts - 2 layers70 × 50.5 mm
- 4 layers105.4 × 57.5 mm
- 2 layers68 × 53 mm
Questions
How big is the Arduino uno board PCB?
It measures 68.6 × 53.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Arduino uno board use?
65 parts, built around the ATMEGA16U2-MU, ATMEGA328P-PU, LMV358 and LP2985-33DBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Arduino uno board KiCad files?
From the goodboy-kwame/Arduino-Uno repository on GitHub, at the commit this page was made from: the board is Ebenezer Banafo-01230492B/arduino uno board.kicad_pcb and its schematic Ebenezer Banafo-01230492B/assignment (2).kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Arduino uno board design in my own project?
Its repository states no licence, so its author keeps all rights: ask goodboy-kwame before reusing the design.