Skip to the content
2 layers47 × 45.7 mmAWG, the printed circuit board in 3D

An open source design of an atmospheric water generator

Size
47 × 45.7 mm
Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
36
Pads
103
Tracks, vias
115, 0
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
25 Mar 2023
Updated
6 Feb 2026

Overview

AWG is an open-source printed circuit board by gongminmin, from the gongminmin/AtmosphericWaterGenerator repository on GitHub, published under the MIT licence. It is a 2-layer board of 47 × 45.7 mm with 24 parts on 36 nets, routed with 115 tracks and 0 vias.

It is built around the DHT11 and RFP30N06LE-VB. Its parts include 6 resistors, 6 connectors, 2 transistors, 1 IC and 1 switch. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

2

README

README.md

Atmospheric Water Generator

License

Atmospheric water generator (AWG) is a device for extracting fresh water from air. There are 0.0001% of water exists in the atmosphere. Even the desert air is not completely dry. Extract it for using is better than nothing. If the extraction is carried out near the ocean, where the air humidity is extremely high, the amount of fresh water obtained can be considerable.

This is a simple open-source AWG design, suitable for home use. We'd like to make it easy to implement, so people can build it at home. The goals are:

  • Low building cost. Off-shelve parts as much as possible.
  • Easy to duplicate.
  • Low operating cost and low power.
  • Simple structure and easy maintenance.
  • Small size and light weight.
  • Safe and reliable.

Principle

To extract water from air, we need a cold source. It condenses the water out for us to collect. The dry and cold air then be used to cool down the heat from the cold source device.

Design

We use a Peltier cooling plate as the cold source. It's a solid semiconductor device, no moving part, easy to use. It as a cold side and a hot side. Two water cooling loops are circuiting between the surfaces of cooling plate to radiators. One loop carries the heat from a radiator to the cold side, makes the radiator cold. The other loop carries the heat from hot side to a radiator, exhaust the heat. The condensed water generated from the cold radiator drops down, collected by a bottle. The cooling plate is power consuming. We need a circuit to control it, keeping the temperature of the cold radiator in a certain range.

Most of the components are off-shelve ones. They are mounted to a frame by 3D printed adapters.

Directories

  • 3DModel folder is the 3D model design of some components. It's in STL format, ready for 3D printing.
  • Circuit folder is the electric design of the system. The files can be open by KiCad
  • Code folder is the Arduino code for the control module.
  • Doc folder contains some documents

License

This project is distributed under the terms of MIT License. See LICENSE for details.

Parts

24
QtyValueFootprintReferences
410KResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1, R3, R5, R7
2100Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR2, R4
210KConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalTH1, TH2
2Fan_3pinConnector_Molex:Molex_KK-254_AE-6410-03A_1x03_P2.54mm_VerticalM1, M2
2RFP30N06LEPackage_TO_SOT_THT:TO-220-3_VerticalQ1, Q2
1Arduino_Nano_v3.xModule:Arduino_NanoA1
1DHT11Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalU1
1DisplayConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ6
1H1MountingHole:MountingHole_2.7mm_M2.5_Pad_ViaH1
1H2MountingHole:MountingHole_2.7mm_M2.5_Pad_ViaH2
1PowerConnector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_VerticalJ1
1Pump 1Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ2
1Pump 2Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ3
1Pump 3Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ4
1SwitchConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalSW1
1TEC1-12702Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalPE1
1WL1Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ5

More from gongminmin/AtmosphericWaterGenerator

1
  • 2 layers63.5 × 27.9 mmAWG protoboard, the printed circuit board in 3D

    AWG protoboard

    gongminmin/AtmosphericWaterGenerator

    An open source design of an atmospheric water generator

    12 parts2MIT

Similar boards

  • 2 layers33 × 25 mmSM Magnet, the printed circuit board in 3D

    SM Magnet

    ortlof/magnet-selfbondage

    1x LILYGO TTGO T1 ESP32 1x Keeppower 18650 3400mAh (Protected) 1x 1A Micro USB 18650 https://www.amazon.de/TECNOIOT-Lithium-Battery-Charging-Charger/dp/B07T52KGDT 1x MT3608 DC-DC Netzteil 1x MOSFET N-CH IRL1404ZPBF-ND…

    7 parts7GPL-3.0
  • 2 layers101 × 73 mmPcb hotplate, the printed circuit board in 3D

    Pcb hotplate

    aaravs-s/pcb_hotplate

    A hotplate for soldering SMD to your pcb's

    17 parts1
  • 2 layers71.1 × 64.1 mmBikeLights, the printed circuit board in 3D

    BikeLights

    jkasari/bikeLightsPCB

    The Schematic and PCB layout for the bikelights on my commuter bike.

    24 parts
  • 2 layers76.2 × 106.7 mmSFS NGENS V1.1, the printed circuit board in 3D

    SFS NGENS V1.1

    NextGen-Environmental-Sensor-Lab/NGENS_SapFlowSensor

    NGENS SAP FLOW SENSOR

    27 parts
  • 2 layers150 × 120 mmHydrogelBioprinter, the printed circuit board in 3D

    HydrogelBioprinter

    SimonDaniel605/Hydrogel-3D-Printer

    Development of a custom hydrogel 3D printer for tissue engineering and research applications for Stellenbosch University.

    174 partsMIT
  • 2 layers101 × 61.6 mmHeater control pcb, the printed circuit board in 3D

    Heater control pcb

    TheCodeSharman/Enclosure

    Custom enclosure frame pieces

    28 partsAGPL-3.0
  • 2 layers91.5 × 100 mmLights pcb, the printed circuit board in 3D

    Lights pcb

    QuinnFreedman/modular

    A collection of free & open source DIY synthesizer module designs for Eurorack

    59 parts116
  • 2 layers76.2 × 61 mmTapeshnik proto, the printed circuit board in 3D

    Tapeshnik proto

    svofski/tapeshnik

    compact cassette data drive

    55 parts14

Questions

How big is the AWG PCB?

It measures 47 × 45.7 mm and has 2 copper layers, 1.6 mm thick.

What parts does the AWG use?

24 parts, built around the DHT11 and RFP30N06LE-VB. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the AWG KiCad files?

From the gongminmin/AtmosphericWaterGenerator repository on GitHub, at the commit this page was made from: the board is Circuit/AWG.kicad_pcb and its schematic Circuit/AWG.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the AWG design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).