2 layers90.6 × 77.8 mm
Emurom
jtsiomb/emurom
ROM emulator. Accepts ROM images through USB and acts as a parallel ROM chip.
58 parts15CC-BY-SA-4.0
2 layers
Templogger
giomf/PCB-Templogger- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 18
- Nets
- 34
- Pads
- 90
- Tracks, vias
- 169, 0
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 20 May 2020
- Updated
- 9 Sep 2020
Overview
Templogger is an open-source printed circuit board by giomf, from the giomf/PCB-Templogger repository on GitHub. It is a 2-layer board with 18 parts on 34 nets, routed with 169 tracks and 0 vias.
It is built around the ATTINY3216-SF and MCP2221-I/P. Its parts include 5 capacitors, 5 ICs, 4 resistors, 2 diodes and 2 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
2
ATTINY3216-SF
SOIC-20-300mil-40℃~+125℃ 16MHz 18 2.7V~5.5V 256Byte 2KB 32KB 8 Bit AVR Built-in FLASH SOIC-20-300mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
MCP2221-I/P
PDIP-14-40℃~+85℃ 3V~5.5V USB to UART、USB to I2C PDIP-14 USB Converters ROHSMicrochip TechnologyUSB Converters
README
README.mdPCB-Templogger
Parts
18| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 330Ω | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_Vertical | R1, R2, R3, R4 |
| 4 | 470nF | Capacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mm | C2, C3, C4, C5 |
| 2 | SC39_11_RT | My Footprints:SC39-11_RT_small | U4, U5 |
| 1 | 10µF | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C1 |
| 1 | ATtiny3216-S | My Footprints:SOIC-20W_7.5x12.8mm_P1.27mm | U2 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2 |
| 1 | LM35-LP | Package_TO_SOT_THT:TO-92 | U3 |
| 1 | MCP2221 | My Footprints:SOIC-14_3.9x8.7mm_P1.27mm | U1 |
| 1 | PWR | LED_THT:LED_D5.0mm | D1 |
| 1 | Sample | LED_THT:LED_D5.0mm | D2 |
| 1 | USB_A | My Footprints:USB_AWF | J1 |
Similar boards
- 4 layers39.8 × 39.8 mm
Low cost multispectral sensor
Matthew-Bon/low_cost_multispectral_sensor
AS726x based sensor with USB interface.
44 partsMIT - 2 layers70 × 60 mm
- 2 layers46 × 22 mm
Power Board
timohueser/MyoSense
As mentioned before the MyoSense Sensor Modules use dry stainless steel electrodes to pick up the small voltages generated by muscle activity on the skin above the monitored muscle.
26 partsGPL-3.0 - 4 layers53 × 39 mm
Avclan mockingboard rounded
halleysfifthinc/AVCLAN-Mockingboard
Emulate a CD Changer on a Toyota AVC LAN network
43 parts65GPL-3.0 - 2 layers30.7 × 34.3 mm
ModbusRtuSensorHub
MichielVanwelsenaere/HomeAutomation.ModbusRtuSensorHub
PCB with small footprint designed to act as a Modbus RTU slave.
23 parts7MIT - 2 layers31.5 × 23.3 mm
- 2 layers151.2 × 89.3 mm
LoadShed
DJM0/LoadShed
Off-grid 4-channel PWM load controller with regulated 12 V output from any 12–32 V battery. Sunrise/sunset + RTC scheduling, LiFePO₄ battery protection, dimming pots and an OLED. ATtiny3216 firmware + KiCad hardware.
94 parts1MIT
Questions
What parts does the Templogger use?
18 parts, built around the ATTINY3216-SF and MCP2221-I/P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Templogger KiCad files?
From the giomf/PCB-Templogger repository on GitHub, at the commit this page was made from: the board is templogger.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Templogger design in my own project?
Its repository states no licence, so its author keeps all rights: ask giomf before reusing the design.