Skip to the content
2 layers42.3 × 96.5 mmVGA Riser, the printed circuit board in 3D

A M68k Multi-Board Computer design. The design basics is as follows: 1) A backplane PCB contains the majority of the bus, such as the address and data lines. 2) Cards slot into the backplane.

Size
42.3 × 96.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
21
Nets
132
Pads
264
Tracks, vias
336, 18
Pours
3
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
12 Dec 2022
Updated
18 Jul 2023

Overview

VGA Riser is an open-source printed circuit board by GeraKuznetsov, from the GeraKuznetsov/M68K-MBC repository on GitHub. It is a 2-layer board of 42.3 × 96.5 mm with 21 parts on 132 nets, routed with 336 tracks and 18 vias.

It is built around the 74HC245D and 74LS32SC. Its parts include 9 connectors, 6 capacitors and 5 ICs.

Main components

2

README

README.md

A M68k Multi-Board Computer design. The design basics is as follows:

  1. A backplane PCB contains the majority of the bus, such as the address and data lines.
  2. Cards slot into the backplane. Cards other then the CPU card should have bus buffers to lower the bus load. (I might give the CPU card buffers too).
  3. The 68k's 16MB memory map is split into 16 1MB regions. This is because the two memory chips used, the sst39f040 flash and AS6C4008 ram are both 0.5MB. (So when you put two of them together to get 16 bits, you end up with 1MB per bank).
  4. Address decoding is done by a pair of decoders on the CPU card. The CS lines from a header on the side of the CPU card to headers on the sides of the other cards, ideally with a twisted ground for each CS line. In the future these lines could be moved into the backplane.
  5. If the card is less then 10x10 cm, I make it 4-layer. 4-layer boards bigger then 10x10cm are too expensive.
  6. the connectors are DIN41612
  7. Line the 16 CS lines, the 7 interrupt lines are also jumpers you plug into the side of the board. There are also 8 interrupt enable jumpers that need to go from the IO card to the CPU card if you want to use one of the parallel output ports as an interrupt enable status port.

IO and CPU cards are currently completely untested, and the memory card is missing a chip to enable the card's data transmitters.

/Schematic/: The actual MBC schematics Note: LS components are sometimes used when the library has no corresponding HC part. All parts are meant to be HC, with the exception of LVC in 5v->3v translation (output to SD card) and HCT in 3v->5v translation (input from SD card). You can use ACT (or AC if you are feeling brave) but at <16Mhz there should not be a need for fast ACT/AC buffers/gluelogic, especially due to the 68k's slow bus cycles (in comparison to say a 6502 or a z80).

Schematics/BP - design for the backplane (TESTED) Schematics/CPU - design for CPU card. (NOT TESTED) Schematics/IO - design for IO card with SD card, PIO, PS2, RTC. (NOT TESTED) Schematics/MEMv2 - second version of the memory card, doesn't even have the layout done. (NOT FINISHED) Schematics/MEMv1 - first version of the memory card, missing 74HC20 and gate to enable the card bus buffers (TESTED) Schematics/Footpp - various footprints Schematics/Lib - various symbols

/Code/ WIP code, just testing stuff, will eventually be OS

/sst39f040_inBB/: Allows you to connect an arduino mega to the backplane and program the flash chips on the memory card in-circuit. TODO: document this better sst39f040_inBB/avr - the arduino mega code sst39f040_inBB/send.py - script file to send the data, requires serial lib

Parts

21
QtyValueFootprintReferences
5100nF68000:DIP-2_200_ELLC1, C2, C3, C4, C5
5Conn_02x0168000:2x01 fingerJ5, J6, J7, J8, J9
474HC24568000:DIP-20U1, U2, U4, U5
22x0868000:2x08 fingerJ2, J4
102x0868000:2x08 fingerJ3
13x32Connector_DIN:DIN41612_R_3x32_Male_Horizontal_THTJ1
174LS3268000:DIP-14U3
1C_Polarized_SmallCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC7
1SJ_BridgedJumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mmJP1

More from GeraKuznetsov/M68K-MBC

5
  • 2 layers152.4 × 162.6 mmVGA, the printed circuit board in 3D

    VGA

    GeraKuznetsov/M68K-MBC

    A M68k Multi-Board Computer design. The design basics is as follows: 1) A backplane PCB contains the majority of the bus, such as the address and data lines. 2) Cards slot into the backplane.

    143 parts10
  • 2 layers109.2 × 106.7 mmCPU, the printed circuit board in 3D

    CPU

    GeraKuznetsov/M68K-MBC

    A M68k Multi-Board Computer design. The design basics is as follows: 1) A backplane PCB contains the majority of the bus, such as the address and data lines. 2) Cards slot into the backplane.

    69 parts10
  • 4 layers99.1 × 99.1 mmSchematics, the printed circuit board in 3D

    Schematics

    GeraKuznetsov/M68K-MBC

    A M68k Multi-Board Computer design. The design basics is as follows: 1) A backplane PCB contains the majority of the bus, such as the address and data lines. 2) Cards slot into the backplane.

    56 parts10
  • 4 layers99.1 × 99.1 mmMEM, the printed circuit board in 3D

    MEM

    GeraKuznetsov/M68K-MBC

    A M68k Multi-Board Computer design. The design basics is as follows: 1) A backplane PCB contains the majority of the bus, such as the address and data lines. 2) Cards slot into the backplane.

    26 parts10
  • 2 layers171.5 × 104.1 mmSchematics, the printed circuit board in 3D

    Schematics

    GeraKuznetsov/M68K-MBC

    A M68k Multi-Board Computer design. The design basics is as follows: 1) A backplane PCB contains the majority of the bus, such as the address and data lines. 2) Cards slot into the backplane.

    23 parts10

Similar boards

  • 2 layers200.7 × 149.9 mmDtz80-complete, the printed circuit board in 3D

    Dtz80-complete

    soster/dtZ80

    A simple 8 Bit computer based on the Z80 CPU

    107 parts15
  • 2 layers235 × 176.5 mmCpu, the printed circuit board in 3D

    Cpu

    Edgeworth/memepu

    cmake -DUSEAFL=yes -DCMAKEBUILDTYPE=Release $PFX/verymeme AFLSKIPCPUFREQ=yes AFLPRELOAD=/usr/local/lib/afl/libdislocator.so \ afl-fuzz -m 1024M -i $PFX/verymeme/testdata/memelang/parsing -o memelangfuzz \ -x…

    286 parts9GPL-3.0
  • 2 layers150 × 150 mm8bit computer, the printed circuit board in 3D

    8bit computer

    halfburnttoast/TCPU8-Alpha

    Discontinued computer I made in 2020

    138 parts4GPL-2.0
  • 2 layers149 × 167 mmMSX 4Slot Expander, the printed circuit board in 3D

    MSX 4Slot Expander

    LVina/MSX4SlotExpander

    MSX 4 Slots Expander Cartridge

    78 parts4GPL-3.0
  • 2 layers190 × 125 mm68hc11, the printed circuit board in 3D

    68hc11

    mggates39/68hc11_SBC

    Building a Single Board Computer around the MC68HC11. It will include my first attempt with KiCad designing a PCB

    58 parts4GPL-3.0
  • 2 layersZ80 ATMEGA, the printed circuit board in 3D

    Z80 ATMEGA

    ozw1z5rd/home-computer-group

    Home Computer Group files

    37 parts3
  • 2 layers104.8 × 101 mmZ2 io test02, the printed circuit board in 3D

    Z2 io test02

    krzys9876/ZX_Spectrum_diy

    KiCad projects (schematics and boards) for a full-diy ZX Spectrum replica

    65 parts2MIT
  • 4 layers304.5 × 217.2 mmLatest Full Backplane, the printed circuit board in 3D

    Latest Full Backplane

    Trilobyte-CPU/8-bit-computer

    A DIY 8-bit computer built mostly with discrete logic chips

    478 parts2

Questions

How big is the VGA Riser PCB?

It measures 42.3 × 96.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the VGA Riser use?

21 parts, built around the 74HC245D and 74LS32SC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the VGA Riser KiCad files?

From the GeraKuznetsov/M68K-MBC repository on GitHub, at the commit this page was made from: the board is Schematics/VGAriser/VGA_Riser.kicad_pcb and its schematic Schematics/BP/BP.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the VGA Riser design in my own project?

Its repository states no licence, so its author keeps all rights: ask GeraKuznetsov before reusing the design.