

Charger mod
Photogrammetry with sensor fusion
- Size
- 28.8 × 27.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 19
- Nets
- 23
- Pads
- 90
- Tracks, vias
- 132, 11
- Pours
- 9
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 9 Mar 2024
- Updated
- 7 Nov 2026
Overview
Charger mod is an open-source printed circuit board by furbrain, from the furbrain/Cyclops repository on GitHub. It is a 2-layer board of 28.8 × 27.3 mm with 19 parts on 23 nets, routed with 132 tracks and 11 vias.
It is built around the BQ25895RTW, MHCI05018-1R0M-R8A and MHS171UBCT. Its parts include 8 capacitors, 4 resistors, 2 ICs, 2 diodes and 2 connectors. It belongs with the power and sensors and measurement boards of this library.
Main components
3BQ25895RTW
WQFN-24-EP(4x4)-40℃~+85℃ 1 12uA 3.9V~14V 4.608V 5A Charging IC I2C Lithium Battery Support Support QFN-24-EP(4x4) Battery Management ROHSTexas InstrumentsBattery ManagementMHCI05018-1R0M-R8A
SMD,5.7x5.4mm17mΩ 1uH 8A 9A Magnetic Shielded Inductor ±20% SMD,5.7x5.4mm Power Inductors ROHSChilisin ElectronicsPower InductorsMHS171UBCT
0805-40℃~+85℃ 140° 2.5V~3.1V 467nm~476nm 468nm 5mA 75mW 90mcd Blue Discrete Diode Side View Mount Water Clear 0805 LED Indication - Discrete ROHSMEIHUALED Indication - Discrete
README
README.mdCyclops
Cave surveying with a camera and IMU. Under development
Parts
19| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10k | Resistor_SMD:R_0402_1005Metric | R2, R3 |
| 2 | 33uF | Capacitor_SMD:C_1206_3216Metric | C1, C2 |
| 2 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1, J2 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C6 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | 2.2k 1% | Resistor_SMD:R_0402_1005Metric | R4 |
| 1 | 220pF | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric | C5 |
| 1 | 261 | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C7 |
| 1 | 47nF | Capacitor_SMD:C_0402_1005Metric | C4 |
| 1 | BQ25895RTW | Package_DFN_QFN:Texas_RTW_WQFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm_ThermalVias | U1 |
| 1 | MHCI05018-1R0M-R8A | footprint:IND-SMD_L5.7-W5.4 | L1 |
| 1 | MHS171UBCT | footprint:LED-SMD_L2.1-W1.0-R-RD | LED1 |
| 1 | NSR10F20NXT5G | Diode_SMD:Nexperia_DSN1608-2_1.6x0.8mm | D1 |
| 1 | TPS22965DSGR | footprint:UDFN-8_L2.0-W2.0-P0.50-TL-EP | U2 |
More from furbrain/Cyclops
3Similar boards
- 4 layers100 × 100 mm

Pi TX 35W PA V2
M0LTE/pi-transceiver
An attempt to build a complete ham radio transceiver around a Raspberry Pi
185 parts15 - 2 layers65 × 56.5 mm

SuperPower RPi KiCAD
SensorsIot/SuperPower
Here you should find the best power supplies for your low-power projects
122 parts600 - 4 layers41.3 × 19 mm

- 4 layers98 × 75 mm

PiFinder4
brickbots/PiFinder
A plate solving telescope finder based around a Raspberry PI and RPI HQ Camera
157 parts257GPL-3.0 - 4 layers83.1 × 92.5 mm

- 4 layers198.4 × 104.3 mm

DC33
Maritime-Hacking-Village/Badge-2025
Public repository for the official MHV 2025 badge.
200 parts15CERN-OHL-W-2.0 - 4 layers114.9 × 129.9 mm

Tanmatsu
Nicolai-Electronics/tanmatsu-hardware
Hardware design of the Tanmatsu mainboard
372 parts9CERN-OHL-P-2.0 - 4 layers50.3 × 21.5 mm

Questions
How big is the Charger mod PCB?
It measures 28.8 × 27.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Charger mod use?
19 parts, built around the BQ25895RTW, MHCI05018-1R0M-R8A and MHS171UBCT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Charger mod KiCad files?
From the furbrain/Cyclops repository on GitHub, at the commit this page was made from: the board is pcb/charger_mod/charger_mod.kicad_pcb and its schematic pcb/charger_mod/charger_mod.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Charger mod design in my own project?
Its repository states no licence, so its author keeps all rights: ask furbrain before reusing the design.

