Skip to the content
25

BQ25895RTW

Texas InstrumentsExtended

-40℃~+85℃ 1 12uA 3.9V~14V 4.608V 5A Charging IC I2C Lithium Battery Support Support QFN-24-EP(4x4) Battery Management ROHS

Part id
ti/BQ25895RTW
Category
Battery Management
Package
WQFN-24-EP(4x4)
Pins
25
In stock
4,623 at JLCPCB (C80200)
Used on
57 open-source boards

Overview

The BQ25895RTW is a battery Management made by Texas Instruments in a WQFN-24-EP(4x4) package with 25 pins. -40℃~+85℃ 1 12uA 3.9V~14V 4.608V 5A Charging IC I2C Lithium Battery Support Support QFN-24-EP(4x4) Battery Management ROHS.

PCBKit's library has its KiCad symbol (Battery_Management:BQ25895RTW, from KiCad's library) and its footprint (Package_DFN_QFN:Texas_RTW_WQFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm, from KiCad's library), ready for a KiCad board. 4,623 are in stock at JLCPCB (part C80200). 57 open-source boards in 44 repositories on GitHub use it.

Symbol

1VBUS2D+3D-4STAT5SCL6SDA7INT8OTG9CE10ILIM11TS12QON13BAT15SYS17PGND19SW21BTST22REGN23PMID24DSEL
Battery_Management:BQ25895RTWFrom KiCad's library

Footprint

25
Package_DFN_QFN:Texas_RTW_WQFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mmFrom KiCad's library

From the datasheet

15
Supply, least
3.9 V · VBUS, recommended operating min · p. 6
Supply, most
14 V · VBUS, recommended operating max · p. 6
Supply, absolute maximum
22 V · VBUS, converter not switching, absolute max · p. 6
Works from
-40 °C · Operating free-air temperature min · p. 6
Works up to
85 °C · Operating free-air temperature max · p. 6
Junction, hottest
150 °C · Junction temperature absolute max · p. 6
Takes working
3 mA · VBUS typical, buck switching, VBAT = 3.2 V, ISYS = 0 A · p. 7
Takes asleep
12 µA · BAT typical, High-Z, BATFET disabled, battery monitor disabled, TJ < 85°C · p. 7
Gives
5 A · SW output current max · p. 6
A pin gives at most
6 mA · INT, STAT sink current absolute max · p. 6
Junction to air (RTW (WQFN))
31.8 K/W · Junction-to-ambient thermal resistance · p. 7
Junction to case (RTW (WQFN))
27.9 K/W · Junction-to-case (top) thermal resistance · p. 7
Junction to board (RTW (WQFN))
8.7 K/W · Junction-to-board thermal resistance · p. 7
Gives
3.1 A · maximum boost mode output current at PMID · p. 19
Switches at
1.5 MHz · typical buck switching frequency · p. 18

What it is and has

17
Charger
5-A, 1.5-MHz switch mode buck · p. 1
Battery chemistry
Single-cell Li-Ion and Li-polymer · p. 1
Boost output
Adjustable 4.5 V to 5.5 V, up to 3.1 A · p. 3
Input current limit
100 mA to 3.25 A, 50-mA resolution · p. 1
Input current optimizer
ICO maximizes input power without overloading adapters · p. 1
ADC
System voltage, temperature, and charge-current monitoring · p. 1
Power path
Narrow VDC (NVDC) power path management · p. 1
BATFET control
Ship Mode, wake up, and full system reset · p. 1
Integration
MOSFETs, current sensing, and loop compensation · p. 1
Protection
Thermal regulation and thermal shutdown · p. 1
Charge voltage accuracy
±0.5% · p. 1
Charge current accuracy
±5% · p. 1
Input current accuracy
±7.5% · p. 1
Package
WQFN (24), 4.00mm x 4.00mm · p. 1
Boost output voltage
Adjustable from 4.5 V to 5.5 V · p. 1
Charge efficiency
93% at 2 A; 91% at 3 A · p. 1
Protection
thermal regulation and thermal shutdown · p. 1

Around it

18
cap 1-µF
between VBUS and PGND; Ceramic; place as close as possible to the IC. · p. 4
res 10-kΩ
between STAT and pull up rail; Charge status output pull-up. · p. 4
res 10-kΩ
between SCL and logic rail; I2C clock pull-up. · p. 4
res 10-kΩ
between SDA and logic rail; I2C data pull-up. · p. 4
res 10-kΩ
between INT and logic rail; Interrupt output pull-up. · p. 4
cap 10uF
between BAT and GND; Place close to BAT. · p. 5
cap 20uF
between SYS and GND; Place close to SYS. · p. 5
cap 0.047µF
between SW and BTST; Bootstrap capacitor. · p. 5
cap 4.7µF
between REGN and analog GND; 10 V rating, ceramic; place close to the IC. · p. 5
cap 8.2 μF
between PMID and PGND; Minimum capacitance when OTG is not used. · p. 5
cap 40 μF
between PMID and PGND; Minimum capacitance with OTG output up to 2.4 A. · p. 5
cap 60 μF
between PMID and PGND; Minimum capacitance with OTG output up to 3.1 A. · p. 5
res 10-KΩ
between DSEL and logic rail; Multiplexer selection output pull-up. · p. 5
other 103AT-2 thermistor
between TS and GND; Recommended NTC thermistor; program the temperature window with a resistor divider from REGN to TS to GND. · p. 5
res 260-Ω
between ILIM and GND; Example hardware input current limit of 1.5 A using KILIM maximum of 390; EN_ILIM must be enabled. · p. 26
cap 8.2 μF
between PMID and GND; Suggested for typical 3 A–5 A charging current. Use low-ESR X7R or X5R ceramic, placed close to PMID and GND; 25 V or higher rating is preferred for inputs up to 14 V. · p. 50
ind 1 µH
between SW and SYS; Recommended for good loop stability. Place the input terminal close to SW. · p. 50
cap 20 µF minimum
between SYS and GND; Recommended for good loop stability. Use X7R or X5R ceramic rated 6 V or higher; place near the inductor and IC. · p. 50

Specifications

162
ParameterConditionsAs printedPage
Voltage range (with respect to GND)VBUS (converter not switching)min -2 · max 22 V6
Voltage range (with respect to GND)PMID (converter not switching)min -0.3 · max 22 V6
Voltage range (with respect to GND)STATmin -0.3 · max 20 V6
Voltage range (with respect to GND)DSELmin -0.3 · max 20 V6
Voltage range (with respect to GND)BTSTmin -0.3 · max 20 V6
Voltage range (with respect to GND)SWmin -2 · max 16 V6
Voltage range (with respect to GND)SW (peak for 10 ns duration)min -3 · max 16 V6
Voltage range (with respect to GND)BAT, SYS (converter not switching)min -0.3 · max 6 V6
Voltage range (with respect to GND)SDA, SCL, INT, OTG, REGN, TS, CE, QONmin -0.3 · max 7 V6
Voltage range (with respect to GND)D+, D–min -0.3 · max 7 V6
Voltage range (with respect to GND)BTST TO SWmin -0.3 · max 7 V6
Voltage range (with respect to GND)PGND to GNDmin -0.3 · max 0.3 V6
Voltage range (with respect to GND)ILIMmin -0.3 · max 5 V6
Output sink currentINT, STATmax 6 mA6
Output sink currentDSELmax 6 mA6
Junction temperaturemin -40 · max 150 °C6
Storage temperature range Tstgmin -65 · max 150 °C6
Electrostatic discharge VESDHuman body model (HBM), per ANSI/ESDA/JEDEC JS-001; rating ±2000 Vmax 2000 V6
Electrostatic discharge VESDCharged device model (CDM), per JEDEC specification JESD22-C101; rating ±250 Vmax 250 V6
Input voltage VINmin 3.9 · max 14 V6
Input current (VBUS) IINmax 3.25 A6
Output current (SW) ISYSmax 5 A6
Battery voltage VBATmax 4.608 V6
Fast charging current IBATmax 5 A6
Discharging current with internal MOSFET IBATContinuousmax 6 A6
Discharging current with internal MOSFET IBATPeak, up to 1 sec durationmax 9 A6
Operating free-air temperature range TAmin -40 · max 85 °C6
Junction-to-ambient thermal resistance RθJABQ25895, RTW (WQFN), 24-PINStyp 31.8 °C/W7
Junction-to-case (top) thermal resistance RθJC((op)BQ25895, RTW (WQFN), 24-PINStyp 27.9 °C/W7
Junction-to-board thermal resistance RθJBBQ25895, RTW (WQFN), 24-PINStyp 8.7 °C/W7
Junction-to-top characterization parameter ψJTBQ25895, RTW (WQFN), 24-PINStyp 0.3 °C/W7
Junction-to-board characterization parameter ψJBBQ25895, RTW (WQFN), 24-PINStyp 8.7 °C/W7
Junction-to-case (bottom) thermal resistance RθJC(bot)BQ25895, RTW (WQFN), 24-PINStyp 2 °C/W7
Battery discharge current (BAT, SW, SYS) in buck mode IBATVBAT = 4.2 V, V(VBUS) < V(UVLO), leakage between BAT and VBUSmax 5 uA7
Battery discharge current (BAT, SW, SYS) in buck mode IBATHigh-Z mode, no VBUS, BATFET disabled (REG09[5]=1), battery monitor disabled, TJ < 85°Ctyp 12 · max 23 uA7
Battery discharge current (BAT, SW, SYS) in buck mode IBATHigh-Z mode, no VBUS, BATFET enabled (REG09[5]=0), battery monitor disabled, TJ < 85°Ctyp 32 · max 60 uA7
Input supply current (VBUS) in buck mode when High-Z mode is enabled I(VBUS_HIZ)V(VBUS)= 5 V, High-Z mode, no battery, battery monitor disabledtyp 15 · max 35 uA7
Input supply current (VBUS) in buck mode when High-Z mode is enabled I(VBUS_HIZ)V(VBUS)= 12 V, High-Z mode, no battery, battery monitor disabledtyp 25 · max 50 uA7
Input supply current (VBUS) in buck mode I(VBUS)VBUS > V(UVLO), VBUS > VBAT, converter not switchingtyp 1.5 · max 3 mA7
Input supply current (VBUS) in buck mode I(VBUS)VBUS > V(UVLO), VBUS > VBAT, converter switching, VBAT = 3.2 V, ISYS = 0Atyp 3 mA7
Input supply current (VBUS) in buck mode I(VBUS)VBUS > V(UVLO), VBUS > VBAT, converter switching, VBAT = 3.8 V, ISYS = 0 Atyp 3 mA7
Battery discharge current in boost mode I(BOOST)VBAT = 4.2 V, boost mode, I(VBUS)= 0 A, converter switchingtyp 5 mA7
VBUS operating range V(VBUS_OP)min 3.9 · max 14 V7
VBUS for active I2C, no battery V(VBUS_UVLOZ)min 3.6 V7
Sleep mode falling threshold V(SLEEP)min 25 · typ 65 · max 120 mV7
Sleep mode rising threshold V(SLEEPZ)min 130 · typ 250 · max 370 mV7
VBUS over-voltage rising threshold V(ACOV)min 14 · max 14.6 V7
VBUS over-voltage falling threshold V(ACOV)min 13.5 · max 14 V7
Battery for active I2C, no VBUS VBAT(UVLOZ)min 2.3 V7
Battery depletion falling threshold VBAT(DPL)min 2.15 · max 2.5 V7
Battery depletion rising threshold VBAT(DPLZ)min 2.35 · max 2.7 V7
Bad adapter detection threshold V(VBUSMIN)typ 3.8 V7
Bad adapter detection current source I(BADSRC)typ 30 mA7
Top reverse blocking MOSFET(RBFET) on-resistance between VBUS and PMID RON(RBFET)TJ = –40°C to +85°Ctyp 27 · max 38 mΩ8
Top reverse blocking MOSFET(RBFET) on-resistance between VBUS and PMID RON(RBFET)TJ = –40°C to +125°Ctyp 27 · max 44 mΩ8
Top switching MOSFET (HSFET) on-resistance between PMID and SW RON(HSFET)TJ = –40°C to +85°Ctyp 27 · max 39 mΩ8
Top switching MOSFET (HSFET) on-resistance between PMID and SW RON(HSFET)TJ = –40°C to +125°Ctyp 27 · max 47 mΩ8
Bottom switching MOSFET (LSFET) on-resistance between SW and GND RON(LSFET)TJ = –40°C to +85°Ctyp 16 · max 24 mΩ8
Bottom switching MOSFET (LSFET) on-resistance between SW and GND RON(LSFET)TJ = –40°C to +125°Ctyp 16 · max 28 mΩ8
BATFET forward voltage in supplement mode V(FWD)BAT discharge current 10 mAtyp 30 mV8
Battery good comparator rising threshold VBAT(GD)VBAT risingmin 3.4 · typ 3.55 · max 3.7 V8
Battery good comparator falling threshold VBAT(GD_HYST)VBAT fallingtyp 100 mV8
Typical charge voltage range VBAT(REG_RANGE)min 3.84 · max 4.608 V8
Typical charge voltage step VBAT(REG_STEP)typ 16 mV8
Charge voltage resolution accuracy VBAT(REG)VBAT = 4.208 V (REG06[7:2]=010111) or VBAT = 4.352 V (REG06[7:2]=100000), TJ = –40°C to +85°Cmin -0.5 · max 0.5 %8
Typical fast charge current regulation range I(CHG_REG__RANGE)min 0 · max 5056 mA8
Typical fast charge current regulation step I(CHG_REG_STEP)typ 64 mA8
Fast charge current regulation accuracy I(CHG_REG_ACC)VBAT = 3.1 V or 3.8 V, ICHG = 128 mA, TJ = –40°C to +85°Cmin -20 · max 20 %8
Fast charge current regulation accuracy I(CHG_REG_ACC)VBAT= 3.1 V or 3.8 V, ICHG = 256 mA, TJ = –40°C to +85°Cmin -10 · max 10 %8
Fast charge current regulation accuracy I(CHG_REG_ACC)VBAT= 3.1 V or 3.8 V, ICHG=1792 mA, TJ = –40°C to +85°Cmin -5 · max 5 %8
Battery LOWV falling threshold VBAT(LOWV)Fast charge to precharge, BATLOWV (REG06[1]) = 1min 2.6 · typ 2.8 · max 2.9 V8
Battery LOWV rising threshold VBAT(LOWV)Precharge to fast charge, BATLOWV (REG06[1])=1; Typical 200-mV hysteresismin 2.8 · typ 3 · max 3.1 V8
Precharge current range I(PRECHG_RANGE)min 64 · max 1024 mA8
Typical precharge current step I(PRECHG_STEP)typ 64 mA8
Precharge current accuracy I(PRECHG_ACC)VBAT=2.6 V, IPRECHG = 256 mAmin -10 · max 10 %8
Termination current range I(TERM_RANGE)min 64 · max 1024 mA8
Typical termination current step I(TERM_STEP)typ 64 mA8
Termination current accuracy I(TERM_ACC)ITERM = 256 mA, ICHG<= 1344 mA, TJ = –20°C to +85°Cmin -12 · max 12 %8
Termination current accuracy I(TERM_ACC)ITERM = 256 mA, ICHG> 1344 mA, TJ = –20°C to +85°Cmin -20 · max 20 %8
Battery short voltage V(SHORT)VBAT fallingtyp 2 V8
Battery short voltage hysteresis V(SHORT_HYST)VBAT risingtyp 200 mV8
Battery short current I(SHORT)VBAT < 2.2 Vtyp 100 mA8
Recharge threshold below VBATREG V(RECHG)VBAT falling, VRECHG (REG06[0]=0) = 0typ 100 mV8
Recharge threshold below VBATREG V(RECHG)VBAT falling, VRECHG (REG06[0]=0) = 1typ 200 mV8
Battery discharge load current IBAT(LOAD)VBAT = 4.2 Vmin 15 mA8
System discharge load current ISYS(LOAD)VSYS = 4.2 Vmin 30 mA8
SYS-BAT MOSFET (BATFET) on-resistance RON(BATFET)TJ = 25°Ctyp 11 · max 13 mΩ8
SYS-BAT MOSFET (BATFET) on-resistance RON(BATFET)TJ = –40°C to +125°Ctyp 11 · max 19 mΩ8
Typical Input voltage regulation range VIN(DPM_RANGE)min 3.9 · max 15.3 V8
Typical Input voltage regulation step VIN(DPM_STEP)typ 100 mV8
Input voltage regulation accuracy VIN(DPM_ACC)VINDPM = 4.4 V, 9 Vmin 3 · max 3 %8
Typical Input current regulation range IIN(DPM_RANGE)min 100 · max 3250 mA8
Typical Input current regulation step IIN(DPM_STEP)typ 50 mA8
Input current regulation accuracy IIN(DPM_ACC)VBAT = 5 V, current pulled from SW; USB150, IINLIM (REG00[5:0]) = 150 mAmin 125 · typ 135 · max 150 mA9
Input current regulation accuracy IIN(DPM_ACC)VBAT = 5 V, current pulled from SW; USB500, IINLIM (REG00[5:0]) = 500 mAmin 440 · typ 470 · max 500 mA9
Input current regulation accuracy IIN(DPM_ACC)VBAT = 5 V, current pulled from SW; USB900, IINLIM (REG00[5:0]) = 900 mAmin 750 · typ 825 · max 900 mA9
Input current regulation accuracy IIN(DPM_ACC)VBAT = 5 V, current pulled from SW; Adapter 1.5 A, IINLIM (REG00[5:0]) = 1500 mAmin 1300 · typ 1400 · max 1500 mA9
Input current regulation during system start up IIN(START)VSYS = 2.2 V, IINLIM (REG00[5:0])> = 200 mAmax 200 mA9
IINMAX = KILIM/RILIM KILIMInput current regulation by ILIM pin = 1.5 Amin 320 · typ 355 · max 390 AxΩ9
D+/D– voltage source (0.6 V) V(0P6_VSRC)min 0.5 · typ 0.6 · max 0.7 V9
D+/D– voltage source (3.45 V) V(3p45_VSRC)min 3.3 · typ 3.45 · max 3.6 V9
D+ connection check current source I(10UA_ISRC)min 7 · typ 10 · max 14 uA9
D+/D– current sink (100 uA) I(100UA_ISINK)min 50 · typ 100 · max 150 uA9
D+/D– Leakage current I(DPDM_LKG)D–, switch openmin -1 · max 1 uA9
D+/D– Leakage current I(DPDM_LKG)D+, switch openmin -1 · max 1 uA9
D+/D– current sink (1.6 mA) I(1P6MA_ISINK)min 1.45 · typ 1.6 · max 1.75 uA9
D+/D– low comparator threshold V(0P4_VTH)min 250 · max 400 mV9
D+ low comparator threshold V(0P8_VTH)max 0.8 V9
D+/D– comparator threshold for non-standard adapter detection (divider 1, 3, or 4) V(2P7_VTH)min 2.55 · max 2.85 V9
D+/D– comparator threshold for non-standard adapter detection (divider 1, 3) V(2P0_VTH)min 1.85 · max 2.15 V9
D+/D– comparator threshold for non-standard adapter detection (divider 2) V(1P2_VTH)min 1.05 · max 1.35 V9
D– pulldown for connection check R(D–_DWN)min 14.25 · max 24.8 kΩ9
Battery over-voltage threshold VBAT(OVP)VBAT rising, as percentage of VBAT(REG)typ 104 %9
Battery over-voltage hysteresis VBAT(OVP_HYST)VBAT falling, as percentage of VBAT(REG)typ 2 %9
System over-current threshold IBAT(FET_OCP)min 9 A9
Junction temperature regulation accuracy TREGREG08[1:0] = 11typ 120 °C9
Thermal shutdown rising temperature TSHUTTemperature risingtyp 160 °C9
Thermal shutdown hysteresis TSHUT(HYS)Temperature fallingtyp 30 °C9
Cold temperature threshold, TS pin voltage rising threshold V(LTF)As percentage to V(REGN)min 72.75 · typ 73.25 · max 73.75 %9
Cold temperature hysteresis, TS pin voltage falling V(LTF_HYS)As percentage to V(REGN)typ 0.4 %9
Hot temperature TS pin voltage rising threshold V(HTF)As percentage to V(REGN)min 47.75 · typ 48.25 · max 48.75 %9
Cut-off temperature TS pin voltage falling threshold V(TCO)As percentage to V(REGN)min 44.25 · typ 44.75 · max 45.25 %9
Cold temperature threshold 1, TS pin voltage rising threshold V(BCOLD1)Boost mode; As percentage to VREGN REG01[5] = 1 (Approximately –20°C w/ 103AT)min 79.5 · typ 80 · max 80.5 %9
Cold temperature threshold 1, TS pin voltage falling threshold V(BCOLD1_HYS)Boost mode; As percentage to VREGN REG01[5] = 1typ 1 %9
Hot temperature threshold 2, TS pin voltage falling threshold V(BHOT2)Boost mode; As percentage to VREGN REG01[7:6] = 10 (Approx. 65°C w/ 103AT)min 30.75 · typ 31.25 · max 31.75 %9
Hot temperature threshold 2, TS pin voltage rising threshold V(BHOT2_HYS)Boost mode; As percentage to VREGN REG01[7:6] =10typ 3 %9
PWM switching frequency, and digital clock FSWOscillator frequencymin 1.32 · max 1.68 MHz9
Maximum PWM duty cycle DMAXtyp 97 %9
Typical boost mode regulation voltage range V(OTG_REG_RANGE)min 4.55 · max 5.55 V9
Typical boost mode regulation voltage step V(OTG_REG_STEP)typ 64 mV9
Boost mode regulation voltage accuracy V(OTG_REG_ACC)I(PMID) = 0 A, BOOSTV=5.126V (REG0A[7:4] = 1001)min -3 · max 3 %9
Battery voltage exiting boost mode V(OTG_BAT)BAT fallingmin 2.6 · max 2.9 V9
Boost mode output current range I(OTG)min 3.1 A9
Boost mode over-voltage threshold V(OTG_OVP)Rising thresholdmin 5.8 · typ 6 V9
REGN LDO output voltage V(REGN)V(VBUS) = 9 V, I(REGN) = 40 mAmin 5.6 · typ 6 · max 6.4 V10
REGN LDO output voltage V(REGN)V(VBUS) = 5 V, I(REGN) = 20 mAmin 4.7 · typ 4.8 V10
REGN LDO current limit I(REGN)V(VBUS) = 9 V, V(REGN) = 3.8 Vmin 50 mA10
Resolution RESRising thresholdtyp 7 bits10
Typical battery voltage range VBAT(RANGE)V(VBUS) > VBAT + V(SLEEP) or OTG mode is enabledmin 2.304 · max 4.848 V10
Typical battery voltage range VBAT(RANGE)V(VBUS) < VBAT + V(SLEEP) and OTG mode is disabled; minimum is VSYS_MINmax 4.848 V10
Typical battery voltage resolution V(BAT_RES)typ 20 mV10
Typical system voltage range V(SYS_RANGE)V(VBUS) > VBAT + V(SLEEP) or OTG mode is enabledmin 2.304 · max 4.848 V10
Typical system voltage range V(SYS_RANGE)V(VBUS) < VBAT + V(SLEEP) and OTG mode is disabled; minimum is VSYS_MINmax 4.848 V10
Typical system voltage resolution V(SYS_RES)typ 20 mV10
Typical VVBUS voltage range V(VBUS_RANGE)V(VBUS) > VBAT + V(SLEEP) or OTG mode is enabledmin 2.6 · max 15.3 V10
Typical VVBUS voltage resolution V(VBUS_RES)typ 100 mV10
Typical battery charge current range IBAT(RANGE)V(VBUS) > VBAT + V(SLEEP) and VBAT > VBAT(SHORT)min 0 · max 6.4 A10
Typical battery charge current resolution IBAT(RES)typ 50 mA10
Typical TS voltage range V(TS_RANGE)min 21 · max 80 %10
Typical TS voltage resolution V(TS_RES)typ 0.47 %10
Input high threshold level VIHLOGIC I/O PIN (OTG, CE, PSEL, QON)min 1.3 V10
Input low threshold level VILLOGIC I/O PIN (OTG, CE, PSEL, QON)max 0.4 V10
High Level Leakage Current IIN(BIAS)LOGIC I/O PIN (OTG, CE, PSEL, QON); Pull-up rail 1.8 Vmax 1 uA10
Internal /QON pull-up V(QON)V(VBUS) = 9 Vtyp 5.8 V10
Internal /QON pull-up V(QON)V(VBUS) = 5 Vtyp 4.3 V10
Internal /QON pull-up resistance R(QON)typ 200 kΩ10
Output low threshold level VOLLOGIC I/O PIN (INT, STAT, PG , DSEL); Sink current = 5 mA, sink currentmax 0.4 V10
High level leakage current IOUT_BIASLOGIC I/O PIN (INT, STAT, PG , DSEL); Pull-up rail 1.8 Vmax 1 uA10
Input high threshold level, SCL and SDA VIHI2C INTERFACE (SCL, SDA); Pull-up rail 1.8 Vmin 1.3 V10
Input low threshold level VILI2C INTERFACE (SCL, SDA); Pull-up rail 1.8 Vmax 0.4 V10
Output low threshold level VOLI2C INTERFACE (SCL, SDA); Sink current = 5 mA, sink currentmax 0.4 V10
High level leakage current IBIASI2C INTERFACE (SCL, SDA); Pull-up rail 1.8 Vmax 1 uA10

Pins, by the datasheet

25
1 VBUS
Charger input voltage; connect a 1-uF ceramic capacitor to PGND close to the IC. · p. 4
2 D+
Positive USB data line for USB host/charging port detection, BC1.2 detection, and MaxCharge. · p. 4
3 D–
Negative USB data line for USB host/charging port detection, BC1.2 detection, and MaxCharge. · p. 4
4 STAT
Charge status output; use a 10-kΩ pull-up. Low indicates charging, high indicates complete or disabled, and 1-Hz blinking indicates a fault. · p. 4
5 SCL
I2C clock; connect to the logic rail through a 10-kΩ resistor. · p. 4
6 SDA
I2C data; connect to the logic rail through a 10-kΩ resistor. · p. 4
7 INT
Interrupt output; use a 10-kΩ pull-up to a logic rail. Sends active-low 256-us pulses reporting status and faults. · p. 4
8 OTG
Boost enable; boost activates when OTG_CONFIG = 1, this pin is high, and no input source is detected at VBUS. · p. 4
9 CE
Active-low charge enable; charging requires CHG_CONFIG = 1 and CE low. Must be pulled high or low. · p. 4
10 ILIM
Input current limit and monitor; a resistor to ground sets the limit as KILIM/RILIM. Can be disabled through EN_ILIM. · p. 4
11 TS
Temperature qualification input; connect an NTC thermistor and resistor divider from REGN to TS to GND. Recommended thermistor is 103AT-2. · p. 5
12 QON
BATFET enable/reset input with internal pull-up; a low pulse exits ship mode or resets system power when VBUS is absent. · p. 5
13 BAT
Battery positive terminal connection; internal BATFET connects BAT to SYS. Place 10uF close to BAT. · p. 5
14 BAT
Battery positive terminal connection; internal BATFET connects BAT to SYS. Place 10uF close to BAT. · p. 5
15 SYS
System power connection; converter maintains minimum system voltage when the battery is low. Place 20uF close to SYS. · p. 5
16 SYS
System power connection; converter maintains minimum system voltage when the battery is low. Place 20uF close to SYS. · p. 5
17 PGND
Power ground; connect directly to input and output capacitor grounds, with a single-point connection to analog ground near the IC. · p. 5
18 PGND
Power ground; connect directly to input and output capacitor grounds, with a single-point connection to analog ground near the IC. · p. 5
19 SW
Switching node for the output inductor; connect a 0.047uF bootstrap capacitor to BTST. · p. 5
20 SW
Switching node for the output inductor; connect a 0.047uF bootstrap capacitor to BTST. · p. 5
21 BTST
PWM high-side driver positive supply; connect a 0.047uF bootstrap capacitor from SW to BTST. · p. 5
22 REGN
PWM low-side driver supply output and TS bias rail; connect a nearby 4.7uF, 10-V ceramic capacitor to analog GND. · p. 5
23 PMID
Battery boost output; minimum capacitance to PGND is 8.2 uF without OTG, 40 uF for OTG up to 2.4 A, or 60 uF for OTG up to 3.1 A. · p. 5
24 DSEL
USB D+/D- multiplexer selection output; use a 10-KΩ pull-up to a logic rail. Low during detection and while MaxCharge is detected. · p. 5
PowerPAD PowerPAD™
Exposed thermal pad; solder to the board and use vias to star-connect the pad plane to PGND and the ground plane. · p. 5

Ordering codes, by the datasheet

6
BQ25895RTWR
WQFN (RTW) · 24 pins; 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 57
BQ25895RTWR.A
WQFN (RTW) · 24 pins; 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 57
BQ25895RTWRG4
WQFN (RTW) · 24 pins; 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 57
BQ25895RTWRG4.A
WQFN (RTW) · 24 pins; 3000 units, LARGE T&R; operating temperature -40 to 85 °C · p. 57
BQ25895RTWT
WQFN (RTW) · 24 pins; 250 units, SMALL T&R; operating temperature -40 to 85 °C · p. 57
BQ25895RTWT.A
WQFN (RTW) · 24 pins; 250 units, SMALL T&R; operating temperature -40 to 85 °C · p. 57

Open-source boards using it

57See all 57
  • 2 layers65 × 56.5 mmSuperPower RPi KiCAD, the printed circuit board in 3D

    SuperPower RPi KiCAD

    SensorsIot/SuperPower

    Here you should find the best power supplies for your low-power projects

    122 parts600
  • 4 layers41.3 × 19 mmKeyword, the printed circuit board in 3D

    Keyword

    notaroomba/keybytes

    A truly modular keyboard

    79 parts444
  • 4 layers98 × 75 mmPiFinder4, the printed circuit board in 3D

    PiFinder4

    brickbots/PiFinder

    A plate solving telescope finder based around a Raspberry PI and RPI HQ Camera

    157 parts257GPL-3.0
  • 4 layers83.1 × 92.5 mmTildagon base, the printed circuit board in 3D

    Tildagon base

    emfcamp/badge-2024-hardware

    183 parts40
  • 4 layers198.4 × 104.3 mmDC33, the printed circuit board in 3D

    DC33

    Maritime-Hacking-Village/Badge-2025

    Public repository for the official MHV 2025 badge.

    200 parts15CERN-OHL-W-2.0
  • 4 layers114.9 × 129.9 mmTanmatsu, the printed circuit board in 3D

    Tanmatsu

    Nicolai-Electronics/tanmatsu-hardware

    Hardware design of the Tanmatsu mainboard

    372 parts9CERN-OHL-P-2.0
  • 4 layers50.3 × 21.5 mmStormbreaker, the printed circuit board in 3D

    Stormbreaker

    VoxelTek/Stormbreaker

    PMS companion board for Thundervolt.

    49 parts4
  • 2 layers78 × 103 mmEmbedded.old, the printed circuit board in 3D

    Embedded.old

    borisg912/3DNA

    This project creates a flat cylindrical DNA model with: - Magnetic DNA bases with color-coded NeoPixel LEDs and unique resistor values for identification - Interactive base pairing game that validates correct DNA base…

    121 parts2GPL-3.0

Parts like it

7

Questions

Is there a KiCad symbol and footprint for the BQ25895RTW?

Yes. The symbol is Battery_Management:BQ25895RTW and the footprint Package_DFN_QFN:Texas_RTW_WQFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the BQ25895RTW?

WQFN-24-EP(4x4), with 25 pins. Its footprint is drawn on this page.

Where is the BQ25895RTW datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the BQ25895RTW?

JLCPCB lists it as part C80200, with 4,623 in stock; the sellers' links on this page open their listings.

What can replace the BQ25895RTW?

Parts like it in the library: the BQ25601DRTW by Texas Instruments, the BQ25886RGE by Texas Instruments, the BQ25601RTW by Texas Instruments and the BQ25887RGE by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the BQ25895RTW?

57 boards in 44 repositories on GitHub; the most starred are listed on this page, with their KiCad files.