

Foosball bot
- Size
- 100 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 38
- Nets
- 89
- Pads
- 250
- Tracks, vias
- 220, 25
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 13 Nov 2024
- Updated
- 20 Nov 2025
Overview
Foosball bot is an open-source printed circuit board by Froggy111, from the Froggy111/foosball-bot repository on GitHub. It is a 2-layer board of 100 × 100 mm with 38 parts on 89 nets, routed with 220 tracks and 25 vias.
It is built around the SN74LVC1T45DBV, FQD50N06-VB and ME6210A50PG. Its parts include 4 capacitors, 4 resistors and 2 transistors. It belongs with the RP2040 boards of this library.
Main components
3SN74LVC1T45DBV
SOT-23-6-40℃~+85℃ 1 1 1.65V~5.5V 1.65V~5.5V 420Mbps Bidirectional Tri-State SOT-23-6 Translators, Level Shifters ROHSTexas InstrumentsTranslators, Level ShiftersFQD50N06-VB
TO-252-55℃~+175℃ 1 N-channel 10mΩ@10V、13mΩ@4.5V 136W 2.65nF 225pF 2V 470pF 47nC@10V 56A 60V N-Channel TO-252 MOSFETs ROHSVBsemi ElecMOSFETsME6210A50PG
SOT-89-3-25℃~+85℃ 1 1.7uA 18V 500mA 5V 8mV@(10mA) Fixed Positive Short Circuit Protection SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMICRONEVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdFoosball robot
Small simple foosball robot
Parts
38| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | TestPoint_Probe | TestPoint:TestPoint_THTPad_D1.5mm_Drill0.7mm | 3V3_TP0, 5V_TP0, 6V_TP0, 36V_TP0, GND_TP0, GND6V_TP0, GND36V_TP0 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4 |
| 3 | SN74LVC1T45DBV | Package_TO_SOT_SMD:SOT-23-6 | LS0, LS1, LS2 |
| 2 | 100kR | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R0, R2 |
| 2 | 100uF | Capacitor_SMD:CP_Elec_8x10 | C0, C1 |
| 2 | 10uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C2, C3 |
| 2 | Conn_01x02 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | EN0, RESET0 |
| 2 | Conn_01x04 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | STEPPER0, UART0 |
| 2 | FQD50N06 | Package_TO_SOT_SMD:TO-252-2 | Q1, Q2 |
| 2 | Screw_Terminal_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2_1x02_P5.00mm_Horizontal | 6VIN_0, 36VIN_0 |
| 1 | 51kR | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R3 |
| 1 | 6.2kR | Resistor_SMD:R_1206_3216Metric_Pad1.30x1.75mm_HandSolder | R1 |
| 1 | Conn_01x03 | Connector_JST:JST_XH_B3B-XH-AM_1x03_P2.50mm_Vertical | SERVO0 |
| 1 | Conn_01x05 | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | I2C0 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | MISC0 |
| 1 | Conn_01x07 | Connector_JST:JST_XH_B7B-XH-A_1x07_P2.50mm_Vertical | SPI1 |
| 1 | Conn_02x06_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_Vertical | 3V3OUT_0 |
| 1 | ME6210A50PG | Package_TO_SOT_SMD:SOT-89-3 | REG0 |
| 1 | Pico | RP-Pico Libraries:RPi_Pico_SMD_TH | MCU0 |
| 1 | Pololu_Breakout_DRV8825 | Module:Pololu_Breakout-16_15.2x20.3mm | STEPPER_DRV0 |
More from Froggy111/foosball-bot
6- 4 layers100 × 100 mm

- 4 layers100 × 100 mm

- 4 layers80 × 100 mm

- 2 layers43 × 38 mm

- 2 layers50 × 50 mm

- 2 layers52 × 40 mm

Similar boards
- 2 layers40 × 65 mm

- 2 layers23.7 × 25.5 mm

Malenki
MarkR42/malenki-esc
A small electronic speed controller for e.g. tiny fighting robots or other rc models
30 parts7 - 4 layers133.8 × 75 mm

- 2 layers93.3 × 69.3 mm

Synkino
fwachsmuth/Synkino
Allows sound playback synchronised to a running,jittery Super 8 projector
145 parts7 - 4 layers70 × 54 mm

- 6 layers80 × 49 mm

ButterStick
butterstick-fpga/butterstick-hardware
Basic ECP5 based GigE to SYZYGY interface.
256 parts225 - 4 layers35 × 85 mm

Vimdrones esc development board
VimDrones/AM32_esc_development_board
Open Source AM32 ESC development board
95 parts44GPL-3.0 - 2 layers30.4 × 12.7 mm

Questions
How big is the Foosball bot PCB?
It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Foosball bot use?
38 parts, built around the SN74LVC1T45DBV, FQD50N06-VB and ME6210A50PG. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Foosball bot KiCad files?
From the Froggy111/foosball-bot repository on GitHub, at the commit this page was made from: the board is v0/hardware/pcb/pcb.kicad_pcb and its schematic v0/hardware/pcb/pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Foosball bot design in my own project?
Its repository states no licence, so its author keeps all rights: ask Froggy111 before reusing the design.