

BarcodeCartridge
Simple cartridge for the Hackaday Superconference 2019 badge, to support a GM65 Barcode reader module
- Size
- 72.4 × 55.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 253
- Nets
- 53
- Pads
- 344
- Tracks, vias
- 145, 5
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20190905)
- Created
- 26 Oct 2019
- Updated
- 16 Nov 2019
Overview
BarcodeCartridge is an open-source printed circuit board by flummer, from the flummer/supercon2019-barcodecartridge repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 2-layer board of 72.4 × 55.9 mm with 253 parts on 53 nets, routed with 145 tracks and 5 vias.
It is built around the LP2985-33DBVR and 10103594-0001LF. Its parts include 5 capacitors, 5 resistors, 2 ICs, 2 transistors and 2 connectors. It belongs with the lEDs and displays boards of this library.
Main components
2LP2985-33DBVR
SOT-23-5-55℃~+150℃@(Tj) 1 10uA 150mA 18V 3.3V 70dB@(1kHz) 90mV@(100mA) Fixed Over Current Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators10103594-0001LF
SMD-30℃~+80℃ 1 1.8A 100V 5P Black Female Micro-B Surface Mount, Right Angle USB 2.0 SMD USB Connectors ROHSAmphenolUSB Connectors
README
README.mdBarcode reader Cartridge for the 2019 Hackaday Superconference Badge

This is designed to use the GM65 barcode reader module, that supports both 1D and 2D barcodes and is able to read from a screen (eg. a smartphone or the screen on the badge)
This cartridge is based on the unofficial Superconference 2019 Badge Cartridge template and hence include the w25q128 SPI flash and a 100nF cap in addition to the 2x20 pin angled male pin header for the badge connection. The flash allows badge configurations and firmware specific to this cartridge to be loaded from the cartridge it self making it selfcontained.
Version 1.2 update
This updated version fixes an error in the pin connections on the cartridge connector (the two columns was flipped for some signals).
Special note about the original version
If you want to use a PCB based on the original version with incorrect connections, it is possible to make a hardware hack on the 20x2 angeled header, where you move the pins around and bend some of them a bit, very precisely.
License
The contents of this repository is released under the following licence:
- the "Creative Commons Attribution-ShareAlike 4.0 International License" (CC BY-SA 4.0) full text of this license is included in the LICENSE file and a copy can also be found at http://creativecommons.org/licenses/by-sa/4.0/
Parts
253| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 0.1uF | Capacitors_SMD:C_0805_HandSoldering | C2, C4 |
| 2 | 22 | Resistors_SMD:R_0805_HandSoldering | R2, R3 |
| 2 | 4.7k | Resistors_SMD:R_0805_HandSoldering | R1, R4 |
| 1 | 100nF | Capacitors_SMD:C_0805_HandSoldering | C1 |
| 1 | 10103594-0001LF | digikey-footprints:USB_Micro_B_Female_10103594-0001LF | J2 |
| 1 | 1uF | Capacitors_SMD:C_0805_HandSoldering | C3 |
| 1 | 2.2uF | Capacitors_SMD:C_0805_HandSoldering | C5 |
| 1 | 6.8k | Resistors_SMD:R_0805_HandSoldering | R5 |
| 1 | Buzzer | Connectors_TestPoints:Test_Point_Pad_d2.0mm | TP1 |
| 1 | Cartridge Connector | SuperconCartridge:Supercon_Cartridge_40pin_Connector | J1 |
| 1 | GM65-S | SuperconCartridge:SD-52892-044 | M1 |
| 1 | GM65-S | SuperconCartridge:GM65-S | READER MODULE |
| 1 | LOGO | Aesthetics:oshw_logo_5.0mm | G*** |
| 1 | LOGO | Aesthetics:HXR_logo_small | G*** |
| 1 | LP2985-33DBVR | digikey-footprints:SOT-753 | U2 |
| 1 | SMD-MOSFET-N-CH-20V-2.1A-CJ2302_SOT-23_ | TO_SOT_Packages_SMD:SOT-23 | Q1 |
| 1 | SMD-MOSFET-P-CH-8V-4.1A-CJ2305_SOT-23_ | TO_SOT_Packages_SMD:SOT-23 | Q2 |
| 1 | SW_Push | Buttons_Switches_SMD:SW_SPST_PTS645 | SW1 |
| 1 | W25Q128 | Housings_SOIC:SO-8_5.3x6.2mm_Pitch1.27mm | U1 |
The 22 most common of 253 parts.
Similar boards
- 4 layers83 × 109 mm

- 2 layers40 × 50 mm

Wired sculpt
chadaustin/wired-sculpt-pcb
KiCad design files for the Wired Sculpt conversion mod
39 parts35 - 8 layers180.6 × 148.5 mm

AMC FMC Carrier PcbDoc
BerkeleyLab/Marble-Mini
"Marble-Mini" Simple FMC carrier board with SFP, 2x FMC, PoE
931 parts24 - 2 layers51.2 × 70.4 mm

Green Pill
IsmaelLopesSilva/Eletronica
Sobre eletrônica (artigos, ebooks, simuladores e outros conteúdos).
29 parts14 - 2 layers45 × 45 mm

Spo2 module v3.0.0 simple dec2024
AEAEmbedded/ESE_PROG
Course repository for Programming 5 (Prog 5) and Programming 6 (Prog 6) of the Embedded Systems Engineering track, Software Engineering, HAN University of Applied Sciences.
35 parts6 - 2 layers65 × 56 mm

Zephyrus IAQ HAT
erinjense/raspberrypi-indoor-air-quality-pcb
Hardware and Software for a Indoor Air Quality Logger
80 parts2MIT - 4 layers83 × 55 mm

- 4 layers97 × 55 mm

UNIT1 R1
svdrecbd/NEMESIS
NEMESIS (Non-periodic Event Monitoring & Evaluation of Stimulus-Induced States). A desktop app for Stentor habituation: live USB-microscope preview, Arduino stepper taps (Periodic/Poisson, seedable), independent MP4…
72 parts1Apache-2.0
Questions
How big is the BarcodeCartridge PCB?
It measures 72.4 × 55.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the BarcodeCartridge use?
253 parts, built around the LP2985-33DBVR and 10103594-0001LF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the BarcodeCartridge KiCad files?
From the flummer/supercon2019-barcodecartridge repository on GitHub, at the commit this page was made from: the board is BarcodeCartridge.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the BarcodeCartridge design in my own project?
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).