
Extron input
rattboi/extron-scart-adapter
Cheap adapter for (some) extron matrix switchers to allow SCART input with no cables

A low-cost IoT water level monitoring device designed to provide visual status indication and remote telemetry for tanks, pits, and other liquid storage applications.
Sensor Indicator is an open-source printed circuit board by finnmo, from the finnmo/IoT-Water-Tank-Level-Monitor repository on GitHub. It is a 2-layer board of 65 × 76 mm with 23 parts on 44 nets, routed with 120 tracks and 0 vias.
It is built around the R-785.0-1.0 and 1N4728A. Its parts include 5 resistors, 3 diodes, 2 transistors, 2 connectors and 1 capacitor. It belongs with the home automation and IoT and sensors and measurement boards of this library.
A low-cost IoT water level monitoring device designed to provide visual status indication and remote telemetry for tanks, pits, and other liquid storage applications.
This project demonstrates the complete hardware development lifecycle from concept through to manufactured PCB and functional prototype.
The device monitors a float switch level sensor and provides:
The goal of this project was to develop a compact, low-cost monitoring solution capable of:
Initial project requirements were identified:
Initial concepts were developed using hand-drawn sketches to define:
The design was captured in KiCad.
Key design elements included:
A custom PCB was designed in KiCad with consideration for:
The design was assembled and tested using:
Hardware validation included:
Several design iterations were completed to resolve:
Final Gerber files were generated from KiCad and submitted for manufacture.
Fabricated boards were assembled and tested against design requirements.
The completed device provides:
docs/
firmware/
hardware/
images/
hardware/
├── schematic/
├── pcb/
├── gerbers/
firmware/
├── platformio.ini
└── src/
docs/
├── design-notes.md
├── testing.md
└── manufacturing.md
images/
├── concept-sketch.jpg
├── schematic.png
├── pcb-layout.png
├── assembled-pcb.jpg
└── final-device.jpg| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H6, H7, H8, H9 |
| 2 | 100R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3, R4 |
| 2 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1, R2 |
| 2 | 2N06L07 | Package_TO_SOT_THT:TO-220-3_Vertical | Q1, Q2 |
| 2 | Screw_Terminal_01x02 | TerminalBlock:TerminalBlock_MaiXu_MX126-5.0-02P_1x02_P5.00mm | GPIO34, VIN1 |
| 1 | 100uF | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C1 |
| 1 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5 |
| 1 | 1N4728A | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D5 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | Fuse | WR-FSH Fuse Holder:J_Wurth_WR-FSH_696108003002 | FUSE1 |
| 1 | GREEN LED | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | D1 |
| 1 | Power Selection Jumper | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | PWR_SEL1 |
| 1 | R-785.0-1.0 | Converter_DCDC:Converter_DCDC_RECOM_R-78E-0.5_THT | U1 |
| 1 | RED LED | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | D2 |
| 1 | ~ | Connector_PinHeader_2.54mm:ESP32_DEVKIT_18x2_2.54mm | TTGO_LoRa-Oled_v1.2 |

rattboi/extron-scart-adapter
Cheap adapter for (some) extron matrix switchers to allow SCART input with no cables

lynchaj/duodyne
Duodyne is a hobbyist retrocomputer system designed to run ROMWBW. It is comprised of modules on a system bus

nico-entz/MyoloV2
A simple muon/particle detector based on STM32 (BluePill), Scintillators and MicroFC SiPMS

david8128/Electeam-Sharky
Firmware designed in ESP32 DEVKIT microcontroller where motor, throttle, breaks, Nextion touch screen and more systems are integrated.


krauser01/portafolio-electronica-eric-rv
Portafolio Proyectos de Electrónica Ing. Eric Rodriguez Vasquez

neriyashalom/PKE-Car-System
Final project - ESP32-S3 based PKE system for vehicle access and ignition

It measures 65 × 76 mm and has 2 copper layers, 1.6 mm thick.
23 parts, built around the R-785.0-1.0 and 1N4728A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the finnmo/IoT-Water-Tank-Level-Monitor repository on GitHub, at the commit this page was made from: the board is Sensor-Indicator .kicad_pcb and its schematic Sensor-Indicator .kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask finnmo before reusing the design.