Skip to the content
2 layers37.1 × 58.2 mmFALCON ESP32, the printed circuit board in 3D

Zadanie rekrutacyjne do koła falcon

Size
37.1 × 58.2 mm
Copper layers
2
Thickness
1.6 mm
Parts
31
Nets
52
Pads
193
Tracks, vias
732, 71
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
20 Mar 2026
Updated
28 Mar 2026

Overview

FALCON ESP32 is an open-source printed circuit board by filkhel, from the filkhel/FALCON_ESP32 repository on GitHub. It is a 2-layer board of 37.1 × 58.2 mm with 31 parts on 52 nets, routed with 732 tracks and 71 vias.

It is built around the ESP32-S3-WROOM-1-N8, AP2112K-3.3 and BMI270. Its parts include 11 resistors, 7 capacitors, 4 switches, 3 ICs and 3 diodes. It belongs with the ESP32 boards of this library.

Main components

3

README

README.md

FALCON_ESP32

Zadanie rekrutacyjne do działu elektroniki koła naukowego FALCON — Politechnika Wrocławska.

Opis projektu

Płytka deweloperska oparta na module ESP32-S3-WROOM-1, inspirowana płytkami typu STM32 Nucleo. Umożliwia wygodną pracę z mikrokontrolerem ESP32-S3 — programowanie przez USB-C, interakcję z użytkownikiem oraz komunikację z czujnikiem inercyjnym BMI270.

Funkcje

  • Programowanie i komunikacja z komputerem przez USB-C (natywne USB ESP32-S3)
  • Regulator napięcia AP2112K-3.3 (5V -> 3.3V)
  • Czujnik IMU BMI270 (żyroskop + akcelerometr) przez I2C
  • 2x złącze pinów 1x20 wyprowadzające GPIO, zasilanie 3.3V i 5V
  • Przyciski: EN (reset), BOOT, BTN1, BTN2
  • LEDy: zasilanie, status, użytkownik
  • Kondensatory filtrujące przy każdym układzie scalonym

Decyzje projektowe

AP2112K zamiast AMS1117 — AP2112K ma mniejszy dropout (ok. 300mV vs 1.2V), mniejszy szum i nie wymaga kondensatorów elektrolitycznych. Lepsza stabilność przy szybkich zmianach obciążenia podczas pracy WiFi ESP32.

Natywne USB ESP32-S3 zamiast układu UART-USB — ESP32-S3 ma wbudowane USB, co eliminuje dodatkowy scalak (np. CP2102), upraszcza schemat i redukuje koszt płytki.

I2C zamiast SPI dla BMI270 — I2C wymaga tylko 2 linii (SDA, SCL) zamiast 4 dla SPI. Przy częstotliwości próbkowania IMU wystarczy prędkość I2C — oszczędność pinów GPIO.

Keep-out zone pod anteną ESP32 — brak ścieżek i miedzi pod anteną WiFi/BT zgodnie z zaleceniami Espressif, co minimalizuje zakłócenia sygnału radiowego.

Schemat pinów

GPIOFunkcja
IO0BOOT
IO4BTN1
IO5BTN2
IO6LED_STATUS
IO7LED_USER
IO8SDA (BMI270)
IO9SCL (BMI270)
IO10BMI_INT
IO19USB_D-
IO20USB_D+

Screenshoty

Zrzut ekranu 2026-03-27 160313

Schemat ideowy w programie KiCad.

Zrzut ekranu 2026-03-27 160405

Układ PCB w programie KiCad.

Zrzut ekranu 2026-03-27 160503

Widok 3D płytki w programie KiCad.

Narzędzia

  • KiCad 9.0
  • Biblioteka footprintu BMI270: SnapEDA

Parts

31
QtyValueFootprintReferences
7100nFCapacitor_SMD:C_0402_1005MetricC1, C2, C3, C4, C5, C6, C7
4SW_PushButton_Switch_SMD:SW_SPST_B3U-1000PSW1, SW2, SW3, SW4
310kResistor_SMD:R_0402_1005MetricR4, R5, R11
333Resistor_SMD:R_0402_1005MetricR6, R7, R8
3LEDLED_SMD:LED_0402_1005MetricD1, D2, D3
24.7KResistor_SMD:R_0402_1005MetricR9, R10
25.1kResistor_SMD:R_0402_1005MetricR1, R2
2Conn_01x20Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_VerticalJ2, J3
110KResistor_SMD:R_0402_1005MetricR3
1AP2112K-3.3Package_TO_SOT_SMD:SOT-23-5U2
1BMI270BMI270:XDCR_BMI270U3
1ESP32-S3-WROOM-1RF_Module:ESP32-S3-WROOM-1U1
1USB_C_Receptacle_USB2.0_14PConnector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12J1

Similar boards

  • 4 layers69 × 81 mmSharpCONSOLE, the printed circuit board in 3D

    SharpCONSOLE

    lastlxrd/Pogopo

    Open-source modular ESP32-S3 handheld console featuring custom hardware, a Sharp Memory LCD, pogopoOS, emulation, motion controls, audio, haptics, and expandable modules.

    196 parts2Apache-2.0
  • 2 layers88 × 115 mmBadge, the printed circuit board in 3D

    Badge

    endsummercamp/badge

    Per l'anno 2024 anche l'End Summer Camp si vuole dotare di un badge interattivo e programmabile, in linea con gli eventi simili internazionali.

    131 parts1CERN-OHL-P-2.0
  • 4 layers52.8 × 56.4 mmESP32 Motor Controller, the printed circuit board in 3D

    ESP32 Motor Controller

    Angelpele/Integrated_FOC_BLDC_Actuator

    Design and development of a portable, self contained closed loop Field Oriented Controller (FOC) for Brushless DC (BLDC) motors built on the ESP32 S3 via a custom designed PCB.

    154 partsMIT
  • 4 layers58 × 58.8 mmCanbus, the printed circuit board in 3D

    Canbus

    iot49/leaves-kicad

    47 parts
  • 4 layers70 × 70 mmWindsensor, the printed circuit board in 3D

    Windsensor

    kristofkatzenberger/windsensor

    This repository contains the design files for a portable wind sensor developed in 2025/26 at the University of Applied Sciences Technikum Wien. This project was completed as part of the Bachelor's Thesis:

    128 partsMIT
  • 4 layers45 × 81 mmRAM R2, the printed circuit board in 3D

    RAM R2

    nimishcoder1232/Bedroom-Engineering-Propulsive-Landing-Project

    This repo has everything that I made for my rocket that can propulsive landing, while still being under ITAR restrictions.

    78 parts
  • 2 layers45.3 × 81 mmRAM R2, the printed circuit board in 3D

    RAM R2

    nimishcoder1232/TVC-Rocket

    This is the repo for my TVC rocket that took two years to develop.

    65 parts
  • 4 layers96 × 60.1 mmCRASHSENSE, the printed circuit board in 3D

    CRASHSENSE

    ParthDhiman32/CRASHSENSE

    Crashsense is a high level embedded sytems project which senses crashes in vehicles like cars trucks and also drones and records the every bit of data of that crash and gives enough data for the crash to be reoncstructed

    56 partsMIT

Questions

How big is the FALCON ESP32 PCB?

It measures 37.1 × 58.2 mm and has 2 copper layers, 1.6 mm thick.

What parts does the FALCON ESP32 use?

31 parts, built around the ESP32-S3-WROOM-1-N8, AP2112K-3.3 and BMI270. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the FALCON ESP32 KiCad files?

From the filkhel/FALCON_ESP32 repository on GitHub, at the commit this page was made from: the board is FALCON_ESP32/FALCON_ESP32.kicad_pcb and its schematic FALCON_ESP32/FALCON_ESP32.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the FALCON ESP32 design in my own project?

Its repository states no licence, so its author keeps all rights: ask filkhel before reusing the design.