Skip to the content
2 layers54.2 × 46.5 mmNeoheart v2, the printed circuit board in 3D

Open Source ATtiny816-based heart shaped PCB with Addressable LEDs!

Size
54.2 × 46.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
46
Nets
48
Pads
169
Tracks, vias
255, 25
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
3 May 2024
Updated
11 May 2025

Overview

Neoheart v2 is an open-source printed circuit board by fellettigiacomo, from the fellettigiacomo/NeoHeart repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 54.2 × 46.5 mm with 46 parts on 48 nets, routed with 255 tracks and 25 vias.

It is built around the TPS61240DRV, SK6805E-J and BSS138, with the CR2032 and TS-1187A-B-A-B among its other parts. Its parts include 25 diodes, 6 capacitors, 4 resistors, 2 connectors and 1 IC. It belongs with the interfaces and adapters boards and the AVR (ATmega, ATtiny) boards of this library.

Main components

5

README

README.md

NeoHeart - Revision 2.2🎉

Hardware and Software design for an Open Source ATtiny816-based heart shaped PCB with Addressable LEDs.

⚠️ Warning: Unfortunately, this release is not yet ready for production. There are still issues with the CR2032 battery not providing enough power, causing glitches and freezes in the LEDs. I'm currently working on a fix. ⚠️

board-render

Project sponsor: PCBWay

Thanks to PCBWay for sponsoring this open-source project. Check out the sponsorship section below to learn more about their support.

Features

  • Microcontroller: ATtiny816
  • LEDs: 25 SK6805-MINIJ Addressable RGB LEDs
  • Power: 3V CR2032 battery
  • Programming: UPDI programming interface
  • Software: Built using Adafruit's Neopixel library, featuring 10 built-in animations and efficient power management
  • Additional Features:
    • Low current consumption design
    • Integrated MOSFET for powering down LEDs to save power
    • Additional digital/analog exposed GPIO to hack your NeoHeart in unexpected ways

2.2 Upgrades

  • Efficient power design: the TPS61240 boost converter has been fully redesigned—now controlled by the MCU via the Enable pin (no more external MOSFET). Improved input stability with additional capacitors, removed feedback resistors for better overall efficiency.
  • Extended Battery Life: ultra-low 0.14 µA quiescent current enables over 10 years of idle operation and supports 1000+ button presses on a single CR2032 cell.
  • Enhanced ATiny816 Stability: added decoupling capacitors to ensure reliable and noise-free microcontroller performance.
  • Upgraded Battery Holder: replaced the CR2032 holder with a more robust and durable version to prevent mechanical failure.
  • Improved Grounding: added a dedicated ground plane for better signal integrity and reduced noise.

Getting Started

To get started with NeoHeart, follow these steps:

  1. Assembly:
    • If you didn't assemble the back using economic PCBA (which I recommend), solder the battery holder.
  2. Powering the Board:
    • Insert a CR2032 battery into the battery holder, ensuring the positive side of the battery matches the positive marking on the board. Alternatively, you can also power the board with the 5V and GND headers
  3. Installing Software:
    • Install the Legacy version of the Arduino IDE (otherwise you will get the a programmer is required to upload error) or PlatformIO
    • Install the Adafruit NeoPixel library.
  4. Connecting the Programmer:
    • Connect your UPDI programmer to the UPDI header on your NeoHeart board. If using an Arduino or any other serial adapter that supports JTAG, follow the instructions provided here.
  5. Uploading the Firmware:
    • Open the firmware sketch provided in the repository.
    • Select the correct board and port in your IDE of choice.
    • Click on the upload button to flash your NeoHeart.
  6. Enjoy:
    • Once programmed, your NeoHeart will be ready to go. Just hit the button and watch those LEDs light up!

Manufacturing

Without including taxes, shipping and with current parts pricing 5 assembled boards (front only, having to solder the battery holder yourself) will cost around 52 USD dollars, so around 10 bucks a board.

You can find all the files for production in the releases tab of this repository.
All parts should available and ready to order, otherwise, feel free to send me a pull request.

Contributing

Any contribution aimed to improving the software or the hardware of NeoHeart are very welcomed. Please feel free to fork this repo, make changes, and submit pull requests.

PCBWay

I've been able to prototype the latest NeoHeart Release thanks to PCBWay that reached out to sponsor this project.
You can see a photo of the boards that PCBWay sent me down here, you can also watch my unboxing video here

Why PCBWay?

  • Quality and Reliability: PCBWay's PCBs meet the highest standards of quality and reliability, they are also capable of meeting the technical demands of any project, from simple projects like mine to very complicated projects.
  • Customization and Flexibility: They offer extensive customization options, allowing board designers to tailor their PCBs precisely to their project's needs.
  • Community Support: PCBWay is a strong supporter of open-source projects, offering sponsorships and discounts to help bring these community-beneficial projects to life. Their commitment to the open-source community makes them a particularly good match for community-driven initiatives.
  • Rapid Prototyping: Time is very important in project development, and PCBWay’s rapid prototyping service allows for quick turnarounds without sacrificing quality.

My Experience with PCBWay

It's been fantastic: our collaboration not only consisted in receiving high-quality PCBs (with PCBA), experiencing a seamless process facilitated by their expert team, from selecting the right components to checking for errors.
I've also received photos of the assembled boards before shipping to ensure everything was perfect!.

Despite different time zones, the response time from their support team was impressive, which I found incredibly helpful.

As I said before, I think it's fantastic that big companies like PCBWay are committed to the open-source community, helping students worldwide bring their projects to life. Thanks again PCBWay!!

License

CERN Open Hardware License - Strongly Reciprocal (CERN-OHL-S)

Parts

46
QtyValueFootprintReferences
25SK6805lib:LED_SK6805_PLCC4_2.4x2.7mm_P1.3mmD1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +9
3PC3TestPoint:TestPoint_Pad_D1.5mmTP1, TP2, TP4
210KResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR4, R5
1100KResistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolderR6
1100nFCapacitor_SMD:C_0603_1608MetricC6
1100nFCapacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolderC2
1100µFCapacitor_SMD:C_1210_3225Metric_Pad1.33x2.70mm_HandSolderC1
11KResistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolderR1
11μHInductor_SMD:L_0805_2012Metric_Pad1.05x1.20mm_HandSolderL1
12.2µFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC5
122μFCapacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolderC4
122μFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC3
1ATtiny816-MNRPackage_DFN_QFN:VQFN-20-1EP_3x3mm_P0.4mm_EP1.7x1.7mmMCU1
1BSS138lib:SOT95P237X112-3NQ2
1CR2032lib:HARWIN_S8421-45RJ2
1Conn_01x03Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ1
1TPS61240lib:SON65P200X200X80-7NU2
1TS-1187A-B-A-BButton_Switch_SMD:SW_Push_1P1T_XKB_TS-1187ASW-ANIM1

The 45 most common of 46 parts.

Similar boards

  • 2 layers44.5 × 26 mmZ2breakout, the printed circuit board in 3D

    Z2breakout

    projectgus/z2breakout

    A (draft) breakout board for the ZipIt Z2 handheld device dock connector

    15 parts1
  • 2 layers98.8 × 68 mmJulkort, the printed circuit board in 3D

    Julkort

    CASE-Association/christmas-cards

    All CASE christmas cards over the years

    30 parts3GPL-3.0
  • 4 layers81.2 × 81.2 mmView base, the printed circuit board in 3D

    View base

    SeedLabs-it/smartknob-hardware

    PCB and CAD files for smartknob devkit

    259 parts47
  • 2 layers28 × 98 mmPino brd v01, the printed circuit board in 3D

    Pino brd v01

    id-studiolab/MLTK01

    Find the full documentation on https://id-studiolab.github.io/MLTK01/

    32 parts2
  • 4 layers150 × 100 mmZpn devboard, the printed circuit board in 3D

    Zpn devboard

    CRImier/MyKiCad

    My KiCad boards. Can't be bothered uploading individually anymore, so here you go.

    168 parts253GPL-3.0
  • 2 layers30 × 50 mmRemmy mcu board, the printed circuit board in 3D

    Remmy mcu board

    ndxw/RemmyMouse

    Remmy uses PJRC's USB mouse library found here, modified to support five mouse buttons.

    26 parts
  • 2 layers100 × 50 mmClock pcb, the printed circuit board in 3D

    Clock pcb

    MitchellStride/Hummingbird-RP2040-Clock-Module

    RP2040 RTC Module, highly compatible with JLCPCB's basic SMT components.

    124 parts2

Questions

How big is the Neoheart v2 PCB?

It measures 54.2 × 46.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Neoheart v2 use?

46 parts, built around the TPS61240DRV, SK6805E-J, BSS138 and CR2032. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Neoheart v2 KiCad files?

From the fellettigiacomo/NeoHeart repository on GitHub, at the commit this page was made from: the board is neoheart_v2.kicad_pcb and its schematic neoheart_v2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Neoheart v2 design in my own project?

Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).