

Tiny 2nmosfet
scheme, pcb, code for drone
- Size
- 24.8 × 17.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 36
- Nets
- 27
- Pads
- 85
- Tracks, vias
- 137, 0
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 19 Mar 2023
- Updated
- 11 Feb 2025
Overview
Tiny 2nmosfet is an open-source printed circuit board by fademike, from the fademike/fly_drone repository on GitHub. It is a 2-layer board of 24.8 × 17.1 mm with 36 parts on 27 nets, routed with 137 tracks and 0 vias.
It is built around the ATTINY13A-SSU, 1N5819WS and FDS6890A. Its parts include 14 resistors, 5 diodes, 2 capacitors, 2 ICs and 2 transistors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3ATTINY13A-SSU
SOIC-8-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 6 64Byte 64Byte 8 Bit AVR Built-in FLASH SOIC-8 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)1N5819WS
SOD-3231 Independent 1A 25A 40V 500uA@40V 600mV@1A SOD-323 Schottky Diodes ROHSGuangdong HottechSchottky DiodesFDS6890A
SOIC-8-55℃~+150℃@(Tj) 1.5V@250uA 18mΩ@7.5A,4.5V 2 N-Channel 2.13nF@10V 20V 32nC@4.5V 7.5A 900mW SOIC-8 MOSFETs ROHSonsemiMOSFETs
README
README.mdfly_drone
My example drone. (in development)

How to connect:
Android phone (AppFlyControl) <-> usb-uart(example: cp2102) <-> uart->rf (STM8S003_AND_SI4463) <-> fly_drone
or:
Android phone (QGroundControl or AppFlyControl) <-wifi-> Linux PC (flyLinuxServer) <-> uart->rf (STM8S003_AND_SI4463) <-> fly_drone
on board:
- DC-DC for 2,3,..S battery operation. To operate on a 1S battery, it is necessary to replace the components to turn off the DC-DC.
- RF SI4463 433MHz radio transceiver. when changing the frequency, you can to change components and programmatically set a different frequency.
- imu mpu6050
- 4pcs 3-pin connector for servo motor/ESC (IMP 1-2 ms) for 4pcs brushed motors need to set mosfet or esc for brushed motors.
- i2c connector, for example: for VL53L0X
- connector for debugging by swdio/uart

For connect brushed motors with esc or servo motor, you can use convertor on attiny13a. example: kicad->tiny_2nmosfet. For connect 4pcs brushed motors, you can use n-mosfet on every channel.
Code:
bootloader (update firmware via RF by FlyLinuxServer)
fly_drone
- mavlink protocol:
-- params list settings(PID, mux chan, motor settings, orientation)
-- RC_CHANNELS
-- COMMAND_LONG - ARM_DISARM/CALIBRATION/REBOOT
-- MSG_STATUSTEXT - logs
- imu, rf, vl53l0x
- acc and gyro calibrate
- for save params and acc calibrate on flash, need to change "flash_params"
- it is compatible with qgroungcontrol (tested on android)
And in repository:
kicad:
- ESC_atmega8 - esc for brashless motor. (need to changed frequency by fuses)
- stm32f103_Fly.. - fly_drone project
- tiny_2nmosfet - esc for connection 4 brashed motors(independent 4 in, 4 out)
video fly_drone.mpg in video repository
Parts
36| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | TestPoint | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11 |
| 8 | 0 | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R5, R6, R7, R8 |
| 6 | 10k | Resistor_SMD:R_0603_1608Metric | R9, R10, R11, R12, R13, R14 |
| 5 | 1N5819WS | Diode_SMD:D_SOD-323 | D2, D3, D4, D5, D6 |
| 2 | 1u | Capacitor_SMD:C_0603_1608Metric | C1, C2 |
| 2 | ATtiny13A-SS | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1, U2 |
| 2 | FDS6890A | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | Q1, Q2 |
More from fademike/fly_drone
2- 2 layers35 × 25 mm

- 2 layers23 × 23 mm

Similar boards
- 4 layers116.5 × 98 mm

Hw v1
Churrosoft/uEFI-v6.x
Speeduino compatible board, x4 ignition channels, x4 injection channels, 2&4 wire IAC
248 parts2 - 2 layers130 × 30 mm

Wordclock2
mad73923/wordclock2PCB_mechanics
Wall-mount clock which shows the clock in words. incl. WIFI for weather information, Twitter, E-Mails etc
60 parts1 - 4 layers20.3 × 47.5 mm

Rocket ejection
jonnydyer/rocket_ejection
Telemetry recorder and ejection driver for model rockets
52 parts - 4 layers115.5 × 66 mm

- 2 layers33 × 30 mm

Mora villogo
kissadamfkut/mora_blinker
Simple LED blinker with ATtiny13A for educational purposes
21 parts34MIT - 2 layers200 × 100 mm

Keyboard
dragonlock2/kicadboards
Offsite backup for the miscellaneous KiCad boards that don't fit elsewhere
225 parts14Apache-2.0 - 2 layers

TX5823
ep092/TX5823
FPV Sender mit Kanalwahl und konfiguration über SPI. Integriertes OSD mit MAX7456 und Spannungswandlern für 5V, 3,3V und 12V über einen Eingangsspannungsbereich von 8V bis 25.2V.
94 parts9 - 2 layers10.2 × 22.3 mm

Questions
How big is the Tiny 2nmosfet PCB?
It measures 24.8 × 17.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Tiny 2nmosfet use?
36 parts, built around the ATTINY13A-SSU, 1N5819WS and FDS6890A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Tiny 2nmosfet KiCad files?
From the fademike/fly_drone repository on GitHub, at the commit this page was made from: the board is kicad/tiny_2nmosfet/tiny_2nmosfet.kicad_pcb and its schematic kicad/ESC_atmega8/ESC_atmega8.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Tiny 2nmosfet design in my own project?
Its repository states no licence, so its author keeps all rights: ask fademike before reusing the design.