Skip to the content
2 layers285.8 × 95.3 mmCr0wn60, the printed circuit board in 3D

UDBに付属のケーブルをUDB、PCBそれぞれのハウジングに取り付けます。 PCとUDBをType-Cケーブルでつなぎ、Remapに接続します。 CUSTOMIZE YOUR KEYBOARDからCr0wn60を選択したのち、Test Matrixモードを使用し全キーが反応することを確認します。 オプションのLEDを取り付けている場合もここで確認します。 > [!TIP] >…

Size
285.8 × 95.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
174
Nets
136
Pads
693
Tracks, vias
1,040, 143
Pours
636
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
27 Mar 2023
Updated
18 Jun 2025

Overview

Cr0wn60 is an open-source printed circuit board by EwdErna, from the EwdErna/Cr0wn60 repository on GitHub, published under the MIT licence. It is a 2-layer board of 285.8 × 95.3 mm with 174 parts on 136 nets, routed with 1,040 tracks and 143 vias.

It is built around the W25Q128JVSIQ and AMS1117. Its parts include 85 diodes, 60 switches, 13 capacitors, 5 resistors and 3 ICs. It belongs with the RP2040 boards of this library.

Main components

2

README

Readme.md

Cr0wn60

Cr0wn60 配下の特徴を持つキーボードです。

  • TreadStone 配列ベースの左右対称配列
  • RP2040 採用の PCB
  • Friction O-ring Mount の 3 ピースケース

ファームウェアは以下のリポジトリから取得可能です。
Ewderna/qmk_firmware ewderna_22 branch

Build Guide

同梱物

  • PCB
    • デフォルトのファームウェアを書き込み済み
  • スイッチプレート
  • ケース
    • トップケース
    • ミドルプレート
    • ボトムケース
  • O-ring ID185x3.55mm
  • Unified Daughter Board S1 / molex Pico EasyMate Cable

[!Note]
ProtoType 版ではスイッチプレート、ケースはデータのみの配布となります。
また、O-ring については付属しません。ご自身で購入をお願いします。

別途必要なもの

  • キースイッチ x60
    • Cherry MX 互換のみ対応
  • スタビライザー
    • PCBマウント 2U x3
  • LED x15 (Optional)
    • SK6812MINI-E 互換品
  • USB Type-C ケーブル
  • キーキャップ x60
    • 1U x48
    • 1.25U x5
    • 1.5U x2
    • 1.75U x2
    • 2.25U x3

組み立て手順

LEDのはんだ付け(Optional)

15個のLEDをはんだ付けします。

スタビライザーの取り付け

PCBにスタビライザーを取り付けます。
PCB表面にスタビライザーのワイヤー側を示すシルクがあります。
向きを間違えないよう注意してください。

スイッチプレートにキースイッチの取り付け

すべてのキースイッチをスイッチプレートに取り付けます。

キースイッチのはんだ付け

プレートごとキースイッチをPCBに取り付け、裏面からはんだ付けします。

動作確認

UDBに付属のケーブルをUDB、PCBそれぞれのハウジングに取り付けます。
PCとUDBをType-Cケーブルでつなぎ、Remapに接続します。
CUSTOMIZE YOUR KEYBOARDからCr0wn60を選択したのち、Test Matrixモードを使用し全キーが反応することを確認します。
オプションのLEDを取り付けている場合もここで確認します。

[!TIP]
LEDが途中から光らない場合は、光らないLEDかその直前の番号のLEDについてはんだ付けを見直してください。
はんだ付けを直しても光らない場合はLEDが壊れている可能性がありますので交換してみてください。

[!TIP]
proto.1、proto.2ではLED番号が逆転しています。LED15が一番最初のLEDで、LED1が一番最後のLEDです。

O-ringの取り付け

スイッチプレートとPCBの隙間に、スイッチに引っかかるようにO-ringを取り付けます。
下側左右の角部分に余裕を持たせるように掛けておくとケースに入れやすくなります。

ケースの組み立て

ボトムケース、ミドルプレート、トップケースの順に重ね、ボトムケースの裏側からM3ねじ8本で固定します。
ミドルプレートの向きに気を付けてください。角の隙間が狭いほうが左側に来るように重ねます。

UDBの取り付け

UDBを、付属のねじでボトムケースに固定します。
付属のケーブルをUDB、PCBのハウジングにそれぞれ取り付けます。向きは特にありません。

ケースにPCBの取り付け

PCBをケースに収めます。
下側左右の角部分に張ったO-ringをトップケースの角に押し付けながら、上側をケース内に押し込みます。
最後に奥まで押し込んで取付完了です。

Parts

174
QtyValueFootprintReferences
70D_SmallDiode_SMD:D_SOD-123D1, DK1, DK2, DK10, DK12, DK13, DK14, DK15, DK16, DK17, DK20, DK21, DK23, DK24, DK25, DK26 +54
48SW_Push_45degSMKJP:SW_Cherry_MX1A_1.00u_PCBSW1, SW2, SW3, SW10, SW12, SW13, SW14, SW15, SW16, SW17, SW21, SW23, SW24, SW25, SW26, SW30 +32
15YS-SK6812MINI-E-Smallkbd:YS-SK6812MINI-E_revLED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8, LED9, LED10, LED11, LED12, LED13, LED14, LED15
70.1uCapacitor_SMD:C_0402_1005MetricC1, C2, C3, C4, C7, C8, C11
4SW_Push_45degSMKJP:SW_Cherry_MX1A_1.50u_PCBSW20, SW37, SW86, SW87
31kResistor_SMD:R_0402_1005MetricR3, R4, R5
3SW_Push_45degSMKJP:SW_Cherry_MX1A_1.25u_PCBSW60, SW80, SW81
3SW_Push_45degSMKJP:SW_Cherry_MX1A_1.75u_PCBSW40, SW76, SW83
210uCapacitor_SMD:C_0402_1005MetricC9, C10
21uCapacitor_SMD:C_0402_1005MetricC5, C6
222Resistor_SMD:R_0402_1005MetricR1, R2
227pCapacitor_SMD:C_0402_1005MetricC12, C13
2SW_PushADeL_kbd:TS-1088R-02026SWR0, SWR1
2SW_Push_45degSMKJP:SW_Cherry_MX1A_2.25u_PCBSW57, SW84
112MCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1AMS1117Package_TO_SOT_SMD:SOT-223-3_TabPin2U1
1Conn_01x02Connector_PinSocket_1.27mm:PinSocket_1x02_P1.27mm_VerticalJ2
1Conn_01x04_MountingPinADeL_kbd:Pico-EZmateJ1
1RP2040_QFN_56Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mmU3
1W25Q128JVSPackage_SO:SOIC-8_5.23x5.23mm_P1.27mmU2

The 171 most common of 174 parts.

Similar boards

  • 2 layersPID Toaster, the printed circuit board in 3D

    PID Toaster

    benkyd/benhardware

    Various hardware projects

    105 parts1
  • 2 layers38.7 × 50.6 mmSmartWatch, the printed circuit board in 3D

    SmartWatch

    PierceMckinnon/SmartWatch

    PCB + SW to make a functional smartwatch

    89 parts1
  • 2 layers24 × 48.5 mmHey, the printed circuit board in 3D

    Hey

    dwan6767/BeepBop

    Small lora devices for remote communication

    40 parts
  • 2 layers65 × 30 mmCustomPico, the printed circuit board in 3D

    CustomPico

    otho-dll/ANUlab_Z-Blade

    Raspberry Pi Pico 2W in a Raspberry Pi Zero formfactor

    51 parts
  • 2 layers53 × 53 mmBillCold V0.01, the printed circuit board in 3D

    BillCold V0.01

    willianlunca/termokip_hardware

    Repositório com arquivos de todo o projeto BillCold

    67 parts
  • 2 layers74.4 × 51.2 mmEsp32-wroom timer, the printed circuit board in 3D

    Esp32-wroom timer

    AlessandroAU/Chorus32-ESP32LapTimer

    This is an ESP32 port of the popular Chorus RF Laptimer

    66 parts102GPL-3.0
  • 2 layers44 × 20.5 mmQrng, the printed circuit board in 3D

    Qrng

    Spooky-Manufacturing/QRNG

    Quantum Random Number Generator

    29 parts86GPL-3.0
  • 4 layers125 × 90 mmAnalog board, the printed circuit board in 3D

    Analog board

    EERNINUO/ArbWave30

    ArbWave30 – 30MHz 任意波形发生器 | FPGA + 高速DAC | SCPI 可控

    295 parts53GPL-3.0

Questions

How big is the Cr0wn60 PCB?

It measures 285.8 × 95.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Cr0wn60 use?

174 parts, built around the W25Q128JVSIQ and AMS1117. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Cr0wn60 KiCad files?

From the EwdErna/Cr0wn60 repository on GitHub, at the commit this page was made from: the board is Cr0wn60.kicad_pcb and its schematic Cr0wn60.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Cr0wn60 design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).