

KitSamD21 vE
Custom little board with the samd21 microcontroller.
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 27
- Nets
- 56
- Pads
- 156
- Tracks, vias
- 373, 28
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 25 Oct 2026
- Updated
- 25 Oct 2026
Overview
KitSamD21 vE is an open-source printed circuit board by ernestalfo, from the ernestalfo/KitSAMD21 repository on GitHub. It is a 2-layer board with 27 parts on 56 nets, routed with 373 tracks and 28 vias.
It is built around the ATSAMD21G18A-AU, 1N4148WS and PRTR5V0U2X. Its parts include 13 capacitors, 4 connectors, 3 resistors, 3 diodes and 2 ICs. It belongs with the SAM D and SAM boards of this library.
Main components
3ATSAMD21G18A-AU
TQFP-48-40℃~+85℃ 1.62V~3.6V 10bit 12bit 256KB 32 Bit 32KB 38 48MHz ARM Cortex-M0+ Built-in FLASH 上电复位(POR)、欠压检测(BOR/LVD/LVR/LVI)、看门狗复位、内置通用定时器、硬件CRC、日历功能、触控功能 TQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)1N4148WS
SOD-3231.25V@150mA 100V 150mA 1uA@75V 200mW 2A 4ns Independent SOD-323 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching DiodesPRTR5V0U2X
SOT-143-55℃~+125℃ 0.3pF、0.8pF 100W 10V、15V 5V 6.5V 6A 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)
README
README.mdCustom little board with the SAMD21 microcontroller with all the pins exposed. [KiCAD project]
Parts
27| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C4, C5, C6, C10 |
| 3 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2, C12 |
| 2 | 1N4148WS | Diode_SMD:D_SOD-323_HandSoldering | D1, D3 |
| 2 | 22pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C8, C9 |
| 2 | Conn_01x20_Socket | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J3, J4 |
| 1 | 10kO | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1 |
| 1 | 1MO | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7 |
| 1 | 22uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | 330 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R2 |
| 1 | 4.5nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C11 |
| 1 | ATSAMD21G18A-A | Package_QFP:TQFP-48_7x7mm_P0.5mm | U1 |
| 1 | Conn_ARM_JTAG_SWD_10 | Connector:Tag-Connect_TC2050-IDC-NL_2x05_P1.27mm_Vertical | J2 |
| 1 | LM2936-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | PRTR5V0U2X | Package_TO_SOT_SMD:SOT-143 | D2 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1 |
| 1 | USB_B_Micro | Connector:USB3131-30-0230-A | J1 |
Similar boards
- 4 layers300 × 308 mm

- 4 layers45 × 35 mm

- 4 layers34 × 63 mm

STSPIN32G4 V2
Scouttman/ZombieServo
Motor Driver for some aliexpress robotic serovos powered by simpleFOC and a STSPIN32g4
91 parts6 - 2 layers140 × 76.9 mm

- 4 layers45 × 60 mm

HPM5361-RMCS Slave V1.0
Kaiser041224/HPM5361-RMCS_Slave-Pro
HPM5361-RMCSSlave-V1.0 是一个基于 KiCad 9 的硬件工程,核心主控为 HPM5361ICB1。从顶层框图、层级原理图和关键器件选型来看,这块板更像一块面向机器人/运动控制场景的从控板,用于通信汇聚、PWM 外设输出、姿态感知、板载存储和基础人机交互。
222 parts2 - 4 layers40.5 × 40.5 mm

HPM5361-RMCS Slave Lite
Kaiser041224/HPM5361-RMCS_Slave-Lite
HPM5361-RMCSSlave-Lite 是一个基于 HPM5361IEG1 的嵌入式控制板。以下说明是根据当前 KiCad 工程中的原理图层级、器件选型和 PCB 丝印整理出来的硬件简介;从接口组合来看,这块板更像是一个面向机器人或分布式控制系统的从控/通信节点。
179 parts1 - 2 layers303.2 × 95.3 mm

Ccd65
westfoxtrot/ccd65
Generic 65% PCB and variants used in CCD's keyboard projects
178 partsCC-BY-SA-4.0 - 4 layers70.8 × 108 mm

Questions
What parts does the KitSamD21 vE use?
27 parts, built around the ATSAMD21G18A-AU, 1N4148WS and PRTR5V0U2X. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the KitSamD21 vE KiCad files?
From the ernestalfo/KitSAMD21 repository on GitHub, at the commit this page was made from: the board is KitSamD21_vE.kicad_pcb and its schematic KitSamD21.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the KitSamD21 vE design in my own project?
Its repository states no licence, so its author keeps all rights: ask ernestalfo before reusing the design.