

Esp32wroomOled V01
esp32wroomOled_V01 kiCaD files
- Size
- 47.5 × 56.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 63
- Nets
- 80
- Pads
- 260
- Tracks, vias
- 983, 61
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 4 Dec 2017
- Updated
- 4 Dec 2017
Overview
Esp32wroomOled V01 is an open-source printed circuit board by erkanCil, from the erkanCil/esp32wroomOled_V01 repository on GitHub. It is a 2-layer board of 47.5 × 56.8 mm with 63 parts on 80 nets, routed with 983 tracks and 61 vias.
It is built around the CP2104EK, ESP32-S3 and MMBT3904, with the DMG2307L and MBR0520 among its other parts. Its parts include 20 capacitors, 17 resistors, 4 ICs, 4 connectors and 3 diodes. It belongs with the ESP32 boards of this library.
Main components
5CP2104EK
-- USB Conversion Modules ROHSSilicon LabsUSB Conversion ModulesESP32-S3
QFN-56-EP(7x7)-40℃~+105℃ -98.4dBm 150Mbps 2.412GHz~2.484GHz 2.4GHz 21dBm 340mA 3V~3.6V 88mA SPI、USB、UART、ADC、I2C、I2S、PWM WiFi transceiver QFN-56-EP(7x7) RF Transceiver ICs ROHSEspressif SystemsRF Transceiver ICsMMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)DMG2307L
SOT-23-55℃~+150℃ 1 P-Channel 1.36W 134mΩ@4.5V 3.8A 30V 371.3pF 3V 45.9pF 51.3pF 8.2nC@10V P-Channel SOT-23 MOSFETs ROHSDiodes IncorporatedMOSFETsMBR0520
SOD-123-55℃~+150℃ 20V 450mV@500mA 5.5A 500mA Independent SOD-123 Schottky Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Schottky Diodes
Parts
63| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 1uF | w_smd_cap:c_0603 | C6, C10, C11, C12, C13, C15, C19, C20, C21, C22, C23 |
| 7 | 10K | w_smd_resistors:r_0603 | R5, R6, R7, R8, R10, R12, R16 |
| 6 | SW_PUSH | Buttons_Switches_SMD:Tact_Switch_Top_PTS820 | BTN_EVET1, BTN_HAYIR1, BTNA1, BTNB1, BTNC1, BTND1 |
| 5 | 10uF | w_smd_cap:c_0603 | C1, C2, C3, C4, C5 |
| 4 | 100K | w_smd_resistors:r_0603 | R1, R2, R14, R15 |
| 2 | 2u2 | w_smd_cap:c_0603 | C14, C17 |
| 2 | 390K | w_smd_resistors:r_0603 | R11, R13 |
| 2 | 470 | w_smd_resistors:r_0603 | R9, R17 |
| 2 | Conn_01x17 | w_pin_strip:pin_strip_17 | J2, J3 |
| 2 | MMBT3904 | TO_SOT_Packages_SMD:SOT-23 | Q2, Q3 |
| 1 | 100n | w_smd_cap:c_0603 | C18 |
| 1 | 1K | w_smd_resistors:r_0603 | R4 |
| 1 | 1N4148 | w_smd_diode:sod323 | D2 |
| 1 | 4K7 | w_smd_resistors:r_0603 | R3 |
| 1 | 4u7 | w_smd_cap:c_0603 | C16 |
| 1 | AP2112-3V3 | w_smd_trans:sot23-5 | U3 |
| 1 | CP2104 | Housings_DFN_QFN:QFN-24-1EP_4x4mm_Pitch0.5mm | U2 |
| 1 | DMG2307L | w_smd_trans:sot23 | Q1 |
| 1 | ESP-32S | Espressif:ESP32-WROOM | U1 |
| 1 | JST_2MM_MALE | w_conn_df13:df13-2p-125ds | J4 |
| 1 | LED_ALT | LEDs:LED_0805 | LED1 |
| 1 | LOGO | logo:karaGoz_10mm | G2 |
| 1 | LOGO | logo:karaGoz_08mm | G1 |
| 1 | LOGO | w_logo:Logo_silk_OSHW_6x6mm | G*** |
| 1 | MBR0520 | Diodes_SMD:D_SOD-123 | D1 |
| 1 | MCP73811_2 | w_smd_trans:sot23-5 | IC1 |
| 1 | RESET | Buttons_Switches_SMD:Tact_Switch_Top_PTS820 | SW8 |
| 1 | SSD1306-096OLED | Displays:SSD1306-096OLED | DS1 |
| 1 | SW_Push_SPDT | w_switch:switch_mmp122-r | SW7 |
| 1 | USB_B_Mini | Connectors:USB_Micro-B_10103594-0001LF | J1 |
Similar boards
- 2 layers59.2 × 41 mm

- 4 layers53.5 × 74.7 mm

- 2 layers160 × 100 mm

Marine gps
mbouyer/marine_chartplotter
Hardware and software for an opencpn-based chartplotter
115 parts6BSD-2-Clause - 2 layers112 × 79 mm

- 4 layers71 × 64 mm

UWB
victorstoica114/UWB_Module_ESP_IDF
ESP-IDF 6.0.2 firmware for the custom UWB Module V1.0 Rev.B, based on an ESP32-S3-WROOM-1-N16R8. The same application image runs on every module; persistent identity and runtime configuration select the role and active…
254 parts1 - 4 layers103 × 126 mm

Senzori iradiere
cs-pub-ro/smart-solar-irradiance-sensor
Open-source hardware & software for a smart wireless sensor that measures solar irradiance.
351 parts - 2 layers60 × 25 mm

- 2 layers83.6 × 76.7 mm

Questions
How big is the Esp32wroomOled V01 PCB?
It measures 47.5 × 56.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esp32wroomOled V01 use?
63 parts, built around the CP2104EK, ESP32-S3, MMBT3904 and DMG2307L. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp32wroomOled V01 KiCad files?
From the erkanCil/esp32wroomOled_V01 repository on GitHub, at the commit this page was made from: the board is esp32wroomOled_V01/esp32wroomOled_V01.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp32wroomOled V01 design in my own project?
Its repository states no licence, so its author keeps all rights: ask erkanCil before reusing the design.