Skip to the content
2 layers65 × 56 mmRaspi quad stepper motor module, the printed circuit board in 3D

Raspi quad stepper motor module

erinjense/raspberrypi-stepper-motor-pcb2

Quad Stepper Motor PCB module for the Raspberry Pi single board computer.

Size
65 × 56 mm
Copper layers
2
Thickness
1.6 mm
Parts
61
Nets
87
Pads
287
Tracks, vias
733, 84
Pours
4
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
9 Oct 2020
Updated
9 Oct 2020

Overview

Raspi quad stepper motor module is an open-source printed circuit board by erinjense, from the erinjense/raspberrypi-stepper-motor-pcb repository on GitHub. It is a 2-layer board of 65 × 56 mm with 61 parts on 87 nets, routed with 733 tracks and 84 vias.

It is built around the DRV8821DCAR and M2.5. Its parts include 23 capacitors, 20 resistors, 6 connectors, 3 ICs and 2 switches. It belongs with the robots and motor control and computers and single-board computers boards of this library.

Main components

2

README

README.md

Quad Stepper Motor Driver, Printed Circuit Board

Disclaimer

This repository, "raspberrypi-stepper-motor-pcb", includes Open Source Hardware "DESGIN FILES AND GUIDES".

THE "DESIGN FILES AND GUIDES" ARE PROVIDED “AS IS”, WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE "DESIGN FILES AND GUIDES" OR THE USE OR OTHER DEALINGS IN THE "DESIGN FILES AND GUIDES".

See LICENSE for further details.

NOTE: This is not a Raspberry Pi "HAT" (Hardware Attached Top). A Raspberry Pi "HAT" is a specification by the Raspberry Pi Foundation set out to ensure various modules designed to interface with the Raspberry Pi do not conflict with each other. It is up to the User to ensure that the GPIO pins within this PCB module does not conflict with other modules, "HAT"s or desired use-cases.

See more within: Raspberry Pi HAT Details

This device is under test and not guaranteed to operate within electrical specifications or desired functionality.

Device Overview

Features

✔️ Interfaces to Raspberry Pi, single-board computer, 40W GPIO Connector.

✔️ Drives up to 4 Stepper Motors.

✔️ Step Mode Control Switches.

  • Full, 1/2, 1/4, and 1/8

✔️ Motor Drive Current Limiting Potentiometers.

✔️ Mixed Decay Mode.

✔️ Minimal Raspberry Pi GPIO Pin Usage

  • Pins: 11, 13, 15, 29, 31

✔️ DC Barrel Jack for commonly available power supplies.

Electrical Specifications

✔️ VM Motor Power Supply (DC barrel jack): 8 ~ 32V

✔️ Continuous Motor Output Current: 0 ~ 1.5 A / Motor Set

✔️ Working Temperature: TBD

Guides

Motor Selection Guide

Coming soon...

Device Operation Guide

Coming soon...

Ordering Guide

This order guide covers the following:

  • Purchasing printed circuit boards from JLCPCB with SMT assembly.
  • Ordering remaining, through-hole, components from LCSC.

Step 1: Upload Gerber Files

  • Download or clone this repository onto your computer.
  • Go to JLCPCB.com
  • Select "Quote Now" on the right-hand of JLCPCB.

  • Select "Add your gerber file" on JLCPCB.
  • Locate the "gerber" directory within this repository on your computer.
  • Select and upload "gerber.zip".

Step 2: Confirm PCB Specifications

  • Confirm the following optional PCB specifications:
    • PCB Qty
    • Surface Finish (Lead-Free is extra money, but I chose this option.)
  • Leave remaining options default unless you have a reason to change.

Step 3: Optional SMT Assembly

  • Toggle "SMT Assembly" option.
  • Select "Assemble top side".
  • Select your "SMT Qty" preference. (5 vs. 2)
  • Leave Tooling holes as: "Added by JLCPCB".
  • Click "Confirm".

  • Upload BOM and CPL

    • Click "Add BOM File".
    • Go to the "assembly" directory within the repository location on your computer.
    • Select "raspi-quad-stepper-motor-module_bom_jlc.csv"
    • Click "Add CPL File".
    • Go to the "assembly" directory within the repository location on your computer.
    • Select "raspi-quad-stepper-motor-module_cpl_jlc.csv"

Step 4: Review Charge Details

  • If you chose "SMT assembly" you will see the SMT devices that will be populated on the boards.

  • Notice that the through-hole components will still need to be ordered and soldered by hand.

Step 5: Purchase Remaining Components on LCSC

Upload Through Hole BOM

  • Go to LCSC.com
  • Select "BOM Tool" within the LCSC banner.
  • Upload BOM File by choosing "select a file" on LCSC.
  • Go to the "assembly" directory within this repository on your computer.
  • Select "raspi-quad-stepper-motor-module_bom_through_hole_lcsc.xlsx"

NOTE: If you did not choose SMT assembly on JLCPCB, you will have to order all the components, not just the through-hole parts, by uploading the "raspi-quad-stepper-motor-module_bom_jlc.csv" instead of "raspi-quad-stepper-motor-module_bom_through_hole_lcsc.xlsx".

Select BOM Column Types

  • Locate the "LCSC Part Number" column.
  • Select "LCSC Part Number" from the above drop-down box.
  • Locate the "Quantity" column.
  • Select "Quantity" from the above drop-down box.
  • Leave remaining columns as "select type".

Step 6: Confirm Purchases

  • Confirm your JLCPCB order.
  • Confirm your LCSC order.

Parts

61
QtyValueFootprintReferences
17100nFCapacitor_SMD:C_0805_2012MetricC1, C4, C5, C6, C7, C10, C11, C12, C14, C15, C16, C17, C18, C20, C21, C22 +1
1110Kraspi-quad-stepper-motor-module:R_0805_2012MetricR1, R6, R7, R8, R9, R11, R15, R16, R17, R18, R20
80.2Resistor_SMD:R_2512_6332MetricR3, R4, R5, R10, R12, R13, R14, R19
41776266-4raspi-quad-stepper-motor-module:TE_1776266-4J3, J4, J5, J6
4M2.5MountingHole:MountingHole_2.7mm_M2.5MK1, MK2, MK3, MK4
210Kraspi-quad-stepper-motor-module:Potentiometer_3296W_VerticalRV1, RV2
210nFraspi-quad-stepper-motor-module:C_0805_2012MetricC13, C23
2470nFraspi-quad-stepper-motor-module:C_0805_2012MetricC9, C19
2DRV8821DCARraspi-quad-stepper-motor-module:SOP50P810X120-49NU2, U3
2SW_DIP_x04raspi-quad-stepper-motor-module:SW_DIP_SPSTx04_Slide_9.78x12.34mm_W7.62mm_P2.54mmSW1, SW2
1100nFraspi-quad-stepper-motor-module:C_0805_2012MetricC3
1100uFraspi-quad-stepper-motor-module:CP_Elec_6.3x7.7C2
1Barrel_Jackraspi-quad-stepper-motor-module:BarrelJack_HorizontalJ2
1LEDraspi-quad-stepper-motor-module:LED_1206_3216MetricD1
1PCA9557PW,118raspi-quad-stepper-motor-module:SOP65P640X110-16NU1
1R_2.2Kraspi-quad-stepper-motor-module:R_0805_2012MetricR2
1Raspberry_Pi_Headerraspi-quad-stepper-motor-module:PinHeader_2x20_P2.54mm_VerticalJ1

Similar boards

  • 2 layers40.9 × 85 mmStudio mic, the printed circuit board in 3D

    Studio mic

    Spirit532/studio_mic

    A simple, easy to build preamplifier for any true condenser capsule, to make a condenser microphone

    63 parts150MIT
  • 2 layers65 × 56 mmPi1541io, the printed circuit board in 3D

    Pi1541io

    hackup/Pi1541io

    Raspberry Pi extension board for the PI1541 project.

    57 parts109CC-BY-SA-4.0
  • 2 layers65 × 56 mmClumsyMIDI, the printed circuit board in 3D

    ClumsyMIDI

    gmcn42/clumsyMIDI

    A THT-only Raspberry Pi expansion board containing a MIDI interface, DAC, and OLED display

    26 parts90CC-BY-SA-4.0
  • 6 layers203 × 151.8 mmPDNode Baseboard, the printed circuit board in 3D

    PDNode Baseboard

    DvidMakesThings/HW_PDNode-600-Pro

    The PDNode-600 is a professional-grade, 600W USB Power Delivery Unit designed specifically for compact 10-inch rack systems, targeting embedded developers, homelab enthusiasts, test benches, and smart infrastructure.

    236 parts86AGPL-3.0
  • 4 layers60 × 127 mmOpenHT RF, the printed circuit board in 3D

    OpenHT RF

    M17-Project/OpenHT-hw

    Repository for the hardware parts of the OpenHT project

    199 parts63
  • 2 layers85 × 56.5 mmModemHAT, the printed circuit board in 3D

    ModemHAT

    astuder/ModemHAT

    Classic Phone Modem HAT for the Raspberry Pi

    111 parts56
  • 4 layers70 × 60 mmMarelleo, the printed circuit board in 3D

    Marelleo

    Zebra-Rodeo/marelleo

    Une boîte qui raconte une histoire quand on pose une figurine dessus. Boîtier, carte, micrologiciel et doc pour la refaire.

    57 parts47
  • 2 layers285.8 × 124.6 mmPunk75, the printed circuit board in 3D

    Punk75

    dsanchezseco/punk75

    Ortholinear keyboard with 75 keys and all components through hole

    194 parts44GPL-3.0

Questions

How big is the Raspi quad stepper motor module PCB?

It measures 65 × 56 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Raspi quad stepper motor module use?

61 parts, built around the DRV8821DCAR and M2.5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Raspi quad stepper motor module KiCad files?

From the erinjense/raspberrypi-stepper-motor-pcb repository on GitHub, at the commit this page was made from: the board is raspi-quad-stepper-motor-module.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Raspi quad stepper motor module design in my own project?

Its repository states no licence, so its author keeps all rights: ask erinjense before reusing the design.