

Spur demo
Musings from my ECE undergraduate research project
- Size
- 63.8 × 105.5 mm
- Copper layers
- 2
- Thickness
- 1.65 mm
- Parts
- 75
- Nets
- 81
- Pads
- 365
- Tracks, vias
- 624, 214
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 22 Aug 2024
- Updated
- 21 Dec 2025
Overview
Spur demo is an open-source printed circuit board by ericmutton, from the ericmutton/spur-project repository on GitHub. It is a 2-layer board of 63.8 × 105.5 mm with 75 parts on 81 nets, routed with 624 tracks and 214 vias.
It is built around the ISL91127IRNZ-T7A, PCF8575PWRE4 and LM393, with the 103AT-2, RK09711110EL and SP0503BAHTG among its other parts. Its parts include 28 resistors, 13 capacitors, 9 connectors, 6 ICs and 6 diodes. It belongs with the radio and wireless boards and the ESP32 and RISC-V boards of this library.
Main components
7ISL91127IRNZ-T7A
QFN-20(4x4)-40℃~+85℃@(TA) 1 1.8V~5.5V 2.5MHz 2A 3.3V Buck-Boost Buck、Boost Built-in Fixed Yes QFN-20(4x4) DC-DC Converters ROHSRenesas ElectronicsDC-DC ConvertersPCF8575PWRE4
TSSOP-24-40℃~+85℃ 16 2.5V~5.5V 2.5uA 25mA 30uA 400kHz 8 I2C Interrupt Output Quasi-bidirectional output Reset function、Cascade and address expansion、Built-in LED driver TSSOP-24 I/O Expanders ROHSTexas InstrumentsI/O ExpandersLM393
SOP-8-16V~16V 0℃~+70℃ 2 2.5mA 250nA 2V~36V 36V 5mV 5nA Fail-safe function Open-drain SOP-8 Comparators ROHSMSKSEMIComparators103AT-2
ThroughholeThroughhole NTC Thermistors ROHSSEMITECNTC ThermistorsRK09711110EL
插件10V 10kΩ 50mW ±20% 插件 Potentiometers, Variable Resistors ROHSALPSALPINEPotentiometers & Variable ResistorsSP0503BAHTG
SOT-143-55℃~+125℃ 10A@8/20us 14V 150W@8/20us 30pF、60pF 5.5V 6V 80nA ESD IEC 61000-4-2、IEC 61000-4-5、IEC 61000-4-4 Three channels Unidirectional SOT-143 ESD and Surge Protection (TVS/ESD) ROHSTECH PUBLICESD And Surge Protection (TVS/ESD)ZXMN2A01FTA
SOT-23-55℃~+150℃ 1 N-channel 2.2A 20V 225mΩ@2.5V 303pF 30pF 3nC@10V 59pF 700mV 806mW N-Channel SOT-23 MOSFETs ROHSDiodes IncorporatedMOSFETs
README
README.mdspur-project
Musings in preparation for the 2025 Summer Platform for Undergraduate Research.
Getting Started
This repository contains the project files created during my Fall 2024 and Spring 2025 semesters.
Hardware
The EDA schematic captures and prototype PC boards are maintained in separate KiCAD projects in the Hardware directory.
- Single-Cell PMIC and Switch-Mode PSU testbench
- NiceRF SA868 walkie-talkie module breakout board
Software
The source code utilizing either the Espressif Systems ESP-IDF Arduino Core (using FreeRTOS) for experimentation or the Zephyr Standalone Application (using ZephyrRTOS) constituting the base radio platform firmware are both maintained in the Software directory.
Scope
The scope of this research project is to build a two-way radio communications platform that remains extensible in arbitrary 'all-mode' FM modulation in both firmware and hardware.
This means adopting modern real-time operating system ecosystems, particularly the two RTOS under consideration are:
- Zephyr Project ZephyrRTOS (a Linux Foundation Project)
- FreeRTOS (under Amazon AWS stewardship as of 2017)
For the hardware, the platform is to allow off-the-shelf (and few bespoke) integration of:
- Wireless communications modules
- GNSS/GPS receivers
- Sub-Ghz transceivers
- LoRa transceivers
- Peripheral Human-Machine Interface Devices (HIDs)
- Potentiometers (Volume, Frequency), Keypad (DTMF, Navigation), Display
- Mono CW Keyer, Keyboard, and USB devices
- External audio source/sink, external modem/vocoder
Groundwork
- Develop a working 'two-way' radio prototype.
- Phase out SA868 Demo Board by building a minimal breakout board
- Make prototype mobile through a rechargable cell and JEITA charger
- Amplify audio output of SA868 with anything other than an LM386 reference design
- Allow end-user to enter new RX and TX frequencies
- All settings available to the end-user
- Persistence of settings between power cycles
Phase 1
For the purposes of this project, the SA868 is limited to arbitrary FM modes:
- Analog FM Voice
- Amateur Packet Reporting System (APRS)
- Premodulated FM Waveforms
In Analog FM Voice, a parrot test or signal strength report (Readability-Strength-Tone) would be satisfactory.
Approach
A first-principles approach in designing this platform is to be taken on:
- inter-device communications interfacing
- sensor device register-level configuration
- factory firmware flashing (see DMO module)
- microcontroller (a)synchronous peripheral utilization
- utilizing vendor hardware abstractions
- device abstraction and tooling
- TI SimpleLink SDK >= v3.3
- SmartRF Studio == v7 (see TI CC1200)
- subsystem abstraction
- device abstraction and tooling
- utilizing operating system abstractions
- target hardware-application decoupling (see ZephyrRTOS)
- communications stack normalization (see USB, IEEE 802.15.4, Bluetooth SIG)
- tracing & debugging meta-tooling (see openocd)
Outcomes
After discovering a lack of ZephyrRTOS Charge API charge enable in the Cirrus Logic implementation of the ti,bq24190, this research project migrated to FreeRTOS. This migration allowed for the creation of bespoke 'device drivers' for the chips utilized in the radio platform. Print debugging was satisfactory in the making of the platform firmware and so the use of OpenOCD with ESP-Prog board was only researched. Zephyr abstractions listed in part 3 of approach were considered and not implemented after the migration to FreeRTOS.
The scope of this project during the one full academic semester resulted in a functional prototype of the radio platform on two breadboards capable of UHF operation of local Richardson city amateur radio infrastructure and two-way communications with a comparable handheld radio. Afterwards in the Spring 2025 semester a handheld radio form-factor two-layer PCB was designed under the Hardware/KiCAD/spur-demo directory.
This project now contains demonstrable embedded radio firmware and human-machine interface design efforts for handheld radio operation.
Parts
75| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R6, R7, R12, R19, R20, R21, R22, R23, R33, R34 |
| 6 | 10u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C5, C6, C7, C8, C9 |
| 4 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D3, D4, D5, D6 |
| 2 | 0k | Resistor_SMD:R_0603_1608Metric | R24, R25 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R30, R31 |
| 2 | 1M | Resistor_SMD:R_0603_1608Metric | R9, R10 |
| 2 | 1x15 | Connector_PinSocket_2.54mm:PinSocket_1x15_P2.54mm_Vertical | J8, J9 |
| 2 | 2.2k | Resistor_SMD:R_0603_1608Metric | R38, R39 |
| 2 | 22u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C10, C11 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R26, R27 |
| 2 | MountingHole_2.7mm_M2_Pad_Via | MountingHole:MountingHole_2.7mm_Pad_Via | H1, H2 |
| 1 | 0R | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 103AT-2 | spur-demo:103AT2 | TH1 |
| 1 | 1122 | spur-demo:BAT_1122 | BT2 |
| 1 | 150k | Resistor_SMD:R_0603_1608Metric | R32 |
| 1 | 1N5819 | Diode_SMD:D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R35 |
| 1 | 1u | Inductor_SMD:L_Coilcraft_XxL4020 | L2 |
| 1 | 1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1 |
| 1 | 1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3 |
| 1 | 2.27k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 2.2M | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 2.2u | Inductor_SMD:L_Coilcraft_XxL4020 | L1 |
| 1 | 265R | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 4.7u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C18 |
| 1 | 47n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4 |
| 1 | 56p | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C12 |
| 1 | 6.86k | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | BQ24193RGER | spur-demo:QFN50P400X400X100-25N-D_BQ24193RGER | IC1 |
| 1 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | Conn_01x08_Socket | spur-demo:HW-834 | J6 |
| 1 | Conn_Coaxial | Connector_Coaxial:SMA_Molex_73251-1153_EdgeMount_Horizontal | J2 |
| 1 | ISL91127IRNZ-T7A | spur-demo:QFN50P400X400X100-21N_ISL91127IRNZ-T7A | IC3 |
| 1 | LM393 | Package_SO:VSSOP-8_3x3mm_P0.65mm | U4 |
| 1 | Level setpoint | Potentiometer_SMD:Potentiometer_Bourns_3314G_Vertical | RV1 |
| 1 | Microphone_Condenser | Sensor_Audio:POM-2244P-C3310-2-R | MK1 |
| 1 | OTG | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabels | JP11 |
| 1 | PAM8392A Module | spur-demo:PAM8392A | J7 |
| 1 | PCF8575PWR | spur-demo:SOP65P640X120-24N_PCF8575PWR | IC2 |
| 1 | PSEL | Jumper:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabels | JP7 |
| 1 | RK09711110EL | spur-demo:RK09711110EL | VR1 |
| 1 | RotaryEncoder_Switch | Rotary_Encoder:RotaryEncoder_Bourns_Horizontal_PEC12R-2x17F-Sxxxx | SW23 |
| 1 | SA868 | sa8x8:G-NICERF_SA868 | U1 |
| 1 | SP0503BAHTG | Package_TO_SOT_SMD:SOT-143_Handsoldering | D1 |
| 1 | SSD1306 Module | spur-demo:SSD1306 | J1 |
| 1 | USB_C_Plug_USB2.0 | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J12 |
| 1 | VMA309 Module | spur-demo:VMA309 | J4 |
| 1 | XCVR_ESP32-C3-DEVKITM-1 | spur-demo:XCVR_ESP32-C3-DEVKITM-1 | U5 |
| 1 | ZXMN2A01F | Package_TO_SOT_SMD:SOT-23 | Q1 |
More from ericmutton/spur-project
4- 2 layers158.2 × 89.4 mm

- 2 layers63.7 × 105.5 mm

Spur demo without display
ericmutton/spur-project
Musings from my ECE undergraduate research project
104 parts4 - 2 layers50.8 × 32 mm

Bms smps testbench
ericmutton/spur-project
Musings from my ECE undergraduate research project
32 parts4 - 2 layers49.6 × 35.6 mm

Similar boards
- 2 layers59 × 42 mm

- 2 layers120 × 100 mm

Enose PCB
Tobias66662/Bachelor-Project-PCB-Designs
PCB to be used in the Enose (for Bachelor Project)
157 parts1 - 4 layers56.5 × 216 mm

- 4 layers125 × 50.1 mm

- 2 layers70 × 57.5 mm

- 2 layers123.2 × 50.2 mm

I2c 24vin
abzman/modular-i2c-board-set
boards designed to be used together to create a modular control system
109 parts1Unlicense - 4 layers30.3 × 90.5 mm

Base station
Tinkerbug-Robotics/TinkerRocket
Model rocket flight computer, ground station, iOS app, and simulation
115 parts1GPL-3.0 - 4 layers72.9 × 61.3 mm

Graphics card rev-2
ShaneTWilliams/worlds-worst-graphics-card
Custom HDMI transmitter PCB with 480 MHz STM32H7 microcontroller
131 parts18MIT
Questions
How big is the Spur demo PCB?
It measures 63.8 × 105.5 mm and has 2 copper layers, 1.65 mm thick.
What parts does the Spur demo use?
75 parts, built around the ISL91127IRNZ-T7A, PCF8575PWRE4, LM393 and 103AT-2. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Spur demo KiCad files?
From the ericmutton/spur-project repository on GitHub, at the commit this page was made from: the board is Hardware/KiCAD/spur-demo/spur-demo.kicad_pcb and its schematic Hardware/KiCAD/bms-smps-testbench/bms-smps-testbench.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Spur demo design in my own project?
Its repository states no licence, so its author keeps all rights: ask ericmutton before reusing the design.
