
Schems
ErickCampos/At-Switch
This repo describes the construction of non-conventional AT switches: - Proximity-based, through IR LEDs and IR Sensors - Puff-based, through piezoelectric disc sensors

This repo describes the construction of non-conventional AT switches: - Proximity-based, through IR LEDs and IR Sensors - Puff-based, through piezoelectric disc sensors
Emissor is an open-source printed circuit board by ErickCampos, from the ErickCampos/At-Switch repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 115.6 × 57.2 mm with 40 parts on 6 nets, routed with 104 tracks and 0 vias.
It is built around the BC548. Its parts include 16 resistors, 8 diodes, 8 transistors and 8 switches.
This repo describes the construction of non-conventional AT switches:
The devices can act as independent triggers, and a minimal desktop driver, called JATSD (Jack AT Switch Driver) allow them to be used as a 'mouse click' interface, which communicates with the computer directly via audio P2 3.5mm jack input.
sudo apt-get install kicad libx11-dev libasound2-dev libportaudio-dev portaudio19-dev2017-2018
FalaBrasil Group (github|webpage)
Laboratory of Visualization, Interaction and Intelligent Systems (LabVIS)
Federal University of Pará (UFPA)
Erick Modesto Campos (github|email)
Cassio Trindade Batista (github|email)
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | R | R4 | R1, R1, R1, R1, R1, R1, R1, R1, R2, R2, R2, R2, R2, R2, R2, R2 |
| 8 | BC548 | TO92 | Q1, Q1, Q1, Q1, Q1, Q1, Q1, Q1 |
| 8 | CONN_3 | PIN_ARRAY_3X1 | K1, K1, K1, K1, K1, K1, K1, K1 |
| 8 | LED | LED-5MM | D1, D1, D1, D1, D1, D1, D1, D1 |

ErickCampos/At-Switch
This repo describes the construction of non-conventional AT switches: - Proximity-based, through IR LEDs and IR Sensors - Puff-based, through piezoelectric disc sensors

ErickCampos/At-Switch
This repo describes the construction of non-conventional AT switches: - Proximity-based, through IR LEDs and IR Sensors - Puff-based, through piezoelectric disc sensors

ErickCampos/At-Switch
This repo describes the construction of non-conventional AT switches: - Proximity-based, through IR LEDs and IR Sensors - Puff-based, through piezoelectric disc sensors

ErickCampos/At-Switch
This repo describes the construction of non-conventional AT switches: - Proximity-based, through IR LEDs and IR Sensors - Puff-based, through piezoelectric disc sensors

ExploreEmbedded/8051_DevelopmentBoard
Design files and sample code for 8051 development Ultra Boards



DarcyJProjects/touchtone555
An open-source DIY, NE555-based analogue synthesizer - play notes with a stylus


clemarfolly/Microdigital-TK2000
Reprodução da PCB do TK-2000 da Microdigital, clone do Micro-Professor MPF-II

Danjovic/Soda-IDE
8 bit Compact Flash Interface for MSX computers

alvaroalea/all-spectrum-clones
Schematic of a 8bit computer, clone of Sinclair ZX Spectrum
It measures 115.6 × 57.2 mm and has 2 copper layers, 1.6 mm thick.
40 parts, built around the BC548. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ErickCampos/At-Switch repository on GitHub, at the commit this page was made from: the board is at-prox/schems/ir-led/Emissor.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).