4 layers59.5 × 60 mm
Hyperram asic
embelon/hyperram_asic_pcb
Test PCB for CARAVEL ASIC with HyperRAM memory (S27KL0641)
45 partsApache-2.0
4 layers70.1 × 89.6 mm
Hyperram cyclonev
embelon/hyperram_cyclonev_pcb3Simple PCB to connect HyperRAM memories to Cyclone V SoC Development Kit via HSMC connector
- Size
- 70.1 × 89.6 mm
- Copper layers
- 4
- Thickness
- 1.51 mm
- Parts
- 65
- Nets
- 132
- Pads
- 483
- Tracks, vias
- 2,019, 203
- Pours
- 147
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 4 Sep 2022
- Updated
- 24 Jan 2026
Overview
Hyperram cyclonev is an open-source printed circuit board by embelon, from the embelon/hyperram_cyclonev_pcb repository on GitHub, published under the Apache-2.0 licence. It is a 4-layer board of 70.1 × 89.6 mm with 65 parts on 132 nets, routed with 2,019 tracks and 203 vias.
It is built around the AP63205WU, S26KL128SDABHI020 and W25Q32JVSSIQ TR, with the S27KL0641DABHI020, SESD1004Q4UG-0020-090 and BSS138 among its other parts. Its parts include 25 capacitors, 15 resistors, 7 connectors, 5 ICs and 5 diodes. It belongs with the FPGA and CPLD boards of this library.
Main components
10
AP63205WU
TSOT-23-6-40℃~+85℃@(TA) 1 1.1MHz 22uA 2A 3.8V~32V 5V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes TSOT-23-6 DC-DC Converters ROHSDiodes IncorporatedDC-DC Converters
S26KL128SDABHI020
FBGA-24(6x8)FBGA-24(6x8) NOR FLASH ROHSInfineon TechnologiesNOR FLASH
W25Q32JVSSIQ TR
SOIC-8-208mil-40℃~+85℃ 2.7V~3.6V 32Mbit 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbond ElecNOR FLASH
S27KL0641DABHI020
VBGA-24VBGA-24 New Arrivals ROHSInfineon TechnologiesDRAM
SESD1004Q4UG-0020-090
UDFN-10(1x2.5)-55℃~+125℃ 0.2pF 2A@8/20us 50nA 7V 9.2V 9V ESD IEC 61000-4-2 Unidirectional UDFN-10(1x2.5) ESD and Surge Protection (TVS/ESD) ROHSLittelfuseTVS
BSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETs
150080VS75000
0805-40℃~+85℃ 12mcd 140° 2.4V 20mA 570nm 572nm Discrete Diode Water Clear 0805 LED Indication - Discrete ROHSWürth ElektronikLED Indication - Discrete
ASP-122952-01
-0.5mm 160P 2 Gold Surface Mount,Vertical - Board-to-Board and Backplane Connector ROHSSamtecBoard-To-Board And Backplane ConnectorBAS40-04
SOT-23Schottky Diodeshongjiacheng
NRS6028T4R7MMGKV
SMD,6x6mm2.7A 2.7A 31mΩ 4.7uH ±20% SMD,6x6mm Power Inductors ROHSTaiyo YudenPower Inductors
README
README.mdExpansion PCB for Cyclone V SoC Development Kit
Using HSMC connector.
On board:
- 8MB HyperRAM memory: S27KL0641DABHI020
- 16MB HyperFlash : S26KL128SDABHI020
- 4MB QSPI FlashNOR: W25Q32JVSSIQ
I/O
- HDMI output
- 2 x PMOD (3V3): PMOD1 (J6), PMOD2 (7)
- 1 x PMOD (3V3 or 5V): PMOD3 (J5)
- 8bit LA header (shared signals with PMOD3/J5)
- 7 debug signals
Images
Parts
65| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C3, C6, C7, C9, C10, C12, C13, C14, C15, C16 |
| 8 | 0 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R8, R9, R11, R12, R13, R14, R15, R16 |
| 8 | 100n | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C17, C18, C19, C20, C21, C22, C23, C24 |
| 4 | 22uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C4, C5, C25 |
| 4 | 4k7 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4 |
| 3 | Conn_02x06_Top_Bottom | hyperram_cyclonev:610112249221_PMOD_Bottom | J5, J6, J7 |
| 3 | SESD1004Q4UG-0020-090 | hyperram_cyclonev:SESD1004Q4UG0020090 | D1, D2, D4 |
| 2 | 1u 16v | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8, C11 |
| 2 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 1 | 12V | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | 150080VS75000 | hyperram_cyclonev:LEDC2012X80N | LED1 |
| 1 | 15k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 220 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10 |
| 1 | 27k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | 5V | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | AP63205WU | Package_TO_SOT_SMD:TSOT-23-6 | IC1 |
| 1 | ASP-122952-01 | hyperram_cyclonev:ASP12295201 | J1 |
| 1 | BAS40-04 | Package_TO_SOT_SMD:SOT-23 | D3 |
| 1 | Conn_02x06_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_Vertical | J4 |
| 1 | Conn_02x10_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J3 |
| 1 | GND | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | HDMI_A | hyperram_cyclonev:685119134923 | J2 |
| 1 | Jumper_3_Bridged12 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1 |
| 1 | NRS6028T4R7MMGKV | hyperram_cyclonev:NRS6028T4R7MMGK | L1 |
| 1 | S26KL128SDABHI020 | hyperram_cyclonev:BGA24C100P5X5_600X800X100 | IC3 |
| 1 | S27KL0641DABHI020 | hyperram_cyclonev:BGA24C100P5X5_600X800X100 | IC5 |
| 1 | TXB0108PWR | hyperram_cyclonev:SOP65P640X120-20N | IC2 |
| 1 | W25Q32JVSSIQ_TR | hyperram_cyclonev:SOIC127P790X216-8N | IC4 |
Similar boards
- 4 layers79.5 × 70 mm
Hyperram asic qfn
embelon/hyperram_asic_qfn_pcb
Test PCB for CARAVEL ASIC in QFP package with HyperRAM memory (S27KL0641)
53 partsApache-2.0 - 4 layers45 × 41.9 mm
Syzygy hyperram hyperflash
embelon/syzygy-hyperram-hyperflash
Syzygy Pod PCB with HyperRAM and HyperFlash memories
36 partsApache-2.0 - 2 layers
- 2 layers95 × 95 mm
- 4 layers39.3 × 51.2 mm
- 4 layers101.6 × 53.3 mm
H730duino
martinribelotta/h730duino
STM32H7 Arduino form factor and software compatible board
111 parts47MIT - 4 layers101.6 × 53.3 mm
Questions
How big is the Hyperram cyclonev PCB?
It measures 70.1 × 89.6 mm and has 4 copper layers, 1.51 mm thick.
What parts does the Hyperram cyclonev use?
65 parts, built around the AP63205WU, S26KL128SDABHI020, W25Q32JVSSIQ TR and S27KL0641DABHI020. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Hyperram cyclonev KiCad files?
From the embelon/hyperram_cyclonev_pcb repository on GitHub, at the commit this page was made from: the board is hyperram_cyclonev.kicad_pcb and its schematic hyperram_cyclonev.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Hyperram cyclonev design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).