2 layers25.4 × 50.8 mm
Stm32....c breakout
electroniceel/stm32....c-breakout
A breakout module for STM32 microcontrollers in LQFP48 and UFQFPN48 footprint.
59 parts20CC-BY-4.0
2 layers20.4 × 32.3 mm
Stm32f0..f breakout
electroniceel/stm32f0..f-breakout2STM32F0..F (TSSOP20) Breakout Module
- Size
- 20.4 × 32.3 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 35
- Nets
- 29
- Pads
- 136
- Tracks, vias
- 503, 46
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 2 Jul 2015
- Updated
- 5 Jan 2018
Overview
Stm32f0..f breakout is an open-source printed circuit board by electroniceel, from the electroniceel/stm32f0..f-breakout repository on GitHub, published under the CC-BY-4.0 licence. It is a 2-layer board of 20.4 × 32.3 mm with 35 parts on 29 nets, routed with 503 tracks and 46 vias.
It is built around the STM32F030F4P6, XC6204B332MR and BAT54S, with the MMZ1608B601C and BSS138 among its other parts. Its parts include 9 capacitors, 6 resistors, 4 diodes, 3 connectors and 2 ICs. It belongs with the interfaces and adapters boards and the STM32 boards of this library.
Main components
5
STM32F030F4P6
TSSOP-20-40℃~+85℃ 12bit 15 16KB 2.4V~3.6V 32 Bit 48MHz 4KB ARM Cortex-M0 Built-in FLASH TSSOP-20 Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)
XC6204B332MR
SOT-23-5-40℃~+85℃ 1 10V 150mA 3.3V 30uVrms 330mV@(100mA) 70dB@(10kHz) 70uA Fixed Over Current Protection、Enable、Short Circuit Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
BAT54S
SOT-231 Pair Series Connection 1V@100mA 200mA 2uA@25V 30V 600mA SOT-23 Schottky Diodes ROHSMDDSchottky Diodes
MMZ1608B601C
0603SMT Chip Bead for Signal LineTDKUncategorisedBSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETs
README
README.mdSTM32F0..F (TSSOP20) Breakout Module
A breakout module for STM32F0 microcontrollers in TSSOP20 footprint.
Basic Features
- Focus on small footprint and direct access to all pins.
- Provides a 8 pin Micro-MaTch header for easy access to SWD and UART.
- Pushbutton for Reset (press <1 second) and starting the bootloader (press >3 seconds).
- Onboard LDO regulator (standard SOT-23-5) can be used for VDD and VDDA, just VDD or disabled completely.
- Use of a crystal (SMT 3.2x2.5mm) is optional.
- Options can be configured using solder bridges.
- Power LED and User LED (on PA0, PF1 or disconnected).
- Size: 20x32mm or 10x8 pins in the standard 2.54mm raster
Currently supported microcontrollers
- STM32F030F4
- STM32F031F4
- STM32F031F6
- STM32F038F6
- STM32F042F4 (USB header must be connected externally)
- STM32F042F6 (USB header must be connected externally)
- STM32F070F6 (USB header must be connected externally)
Schematics & Layout
Schematics & Layout were done in KiCAD.
Picture
License
This work is licensed under a Creative Commons Attribution 4.0 International License.
Parts
35| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | Solderbridge | modules:Solderbridge | SB1, SB2, SB3, SB4, SB5, SB6 |
| 3 | 1µF | modules:SMD0603-wide-C | C5, C6, C7 |
| 2 | 100nF | modules:SMD0603-wide-C | C4, C8 |
| 2 | 20pF | modules:SMD0603-wide-C | C1, C2 |
| 2 | 330R | modules:SMD0603-wide-R | R2, R4 |
| 2 | 4.7µF | modules:SMD0805-wide-C | C3, C9 |
| 2 | BAT54S | modules:SOT-23 | D3, D4 |
| 2 | CONN_01X10 | Pin_Headers:Pin_Header_Straight_1x10 | P1, P3 |
| 2 | MMZ1608B601C | modules:SMD0603-wide | FB1, FB2 |
| 1 | 0R | modules:SMD0603-wide-R | R5 |
| 1 | 10K | modules:SMD0603-wide-R | R3 |
| 1 | 12MHz | modules:smd-xtal-3225 | X1 |
| 1 | 1K | modules:SMD0603-wide-R | R6 |
| 1 | 820K | modules:SMD0603-wide-R | R1 |
| 1 | BSS138 | modules:SOT-23 | Q1 |
| 1 | LED | modules:SMD0603-wide-diode | D1 |
| 1 | LED green | modules:SMD0603-wide-diode | D2 |
| 1 | MicroMatch_8pin | Connectors_Micro-MaTch:Conn-Micromatch-SMD-8 | P2 |
| 1 | STM32F030F4 | modules:TSSOP-20_4.4x6.5mm_Pitch0.65mm | U1 |
| 1 | SW_PUSH-SPST-NO | modules:Push-Button-SMD-6.0x3.5mm | SW1 |
| 1 | XC6204B332MR | modules:SOT-23-5 | U2 |
Similar boards
- 4 layers100 × 100 mm
MWGEN G1
MR-DOS/MWGEN-G1
12.5 MHz - 6400 MHz (LMX2572) or even up to 20 GHz (LMX2595) generator board with int./ext. reference.
373 parts18GPL-3.0 - 2 layers88.9 × 80 mm
- 2 layers46 × 38 mm
- 4 layers25.6 × 38.6 mm
- 2 layers62.5 × 87.5 mm
Same70
brengi/CESE-PCB
Curso de Diseño de Circuitos Impresos de la Carrera de Especialización en Sistemas Embebidos
72 parts7 - 2 layers50 × 50 mm
- 2 layers34 × 34 mm
Questions
How big is the Stm32f0..f breakout PCB?
It measures 20.4 × 32.3 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Stm32f0..f breakout use?
35 parts, built around the STM32F030F4P6, XC6204B332MR, BAT54S and MMZ1608B601C. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Stm32f0..f breakout KiCad files?
From the electroniceel/stm32f0..f-breakout repository on GitHub, at the commit this page was made from: the board is stm32f0..f-breakout.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Stm32f0..f breakout design in my own project?
Its repository publishes it under the CC-BY-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).