

DesignESP32PCB
- Size
- 52.1 × 76.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 50
- Nets
- 92
- Pads
- 265
- Tracks, vias
- 504, 62
- Pours
- 28
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 5 Feb 2024
- Updated
- 2 May 2024
Overview
DesignESP32PCB is an open-source printed circuit board by ECE-445, from the ECE-445/smart-insole repository on GitHub. It is a 2-layer board of 52.1 × 76.2 mm with 50 parts on 92 nets, routed with 504 tracks and 62 vias.
It is built around the ESP32-S3-WROOM-1-N8, PJS008U-3000-0 and D3V3XA4B10LP, with the MPU-6050, TLV75801PDRV and B3F-4000 among its other parts. Its parts include 25 resistors, 8 capacitors, 4 ICs, 4 connectors and 4 switches. It belongs with the ESP32 and RISC-V boards of this library.
Main components
7ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesPJS008U-3000-0
插件14.18mm MicroSD Card (TF Card) Push-Pull 插件 SD Card / Memory Card Connector ROHSYamaichi ElectronicsSD Card / Memory Card ConnectorD3V3XA4B10LP
UDFN2510-10-55℃~+150℃ 0.35pF 1uA 24W@8/20us 3.3V 4A@8/20us 9.4V 9V ESD Four channels IEC 61000-4-2、IEC 61000-4-5 UDFN2510-10 ESD and Surge Protection (TVS/ESD) ROHSDiodes IncorporatedESD And Surge Protection (TVS/ESD)MPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometersTLV75801PDRV
WSON-6-EP(2x2)-40℃~+125℃@(Tj) 1 31uA 500mA 50dB@(1kHz) 53uVrms 550mV~5.5V 6V Adjustable Positive Under Voltage Lockout、Over Current Protection、Soft Start、Thermal Shutdown WSON-6-EP(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsB3F-4000
插件-4P,12x12mm-25℃~+70℃ 1.3N 12mm 12mm 24V 3 million cycles 4.3mm 50mA PC Pin Round Button SPST-NO Through Hole Plugin-4P,12x12mm Tactile Switches ROHSOmronTactile SwitchesSS8050-G
SOT-231 NPN 1.5A 100 100MHz 100nA 25V 300mW 400mV 5V NPN SOT-23 Bipolar (BJT) ROHSComchipBipolar (BJT)
Parts
50| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 1k | Resistor_SMD:R_0603_1608Metric | R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R22 |
| 4 | 10k | Resistor_SMD:R_0603_1608Metric | R23, R24, R25, R26 |
| 4 | B3F-4000 | SmartInsolePCB:SW_B3F-4000_OMR | SW1, SW2, SW3, SW4 |
| 3 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3 |
| 3 | 1.0k | Resistor_SMD:R_0603_1608Metric | R3, R15, R21 |
| 3 | 10uF | Capacitor_SMD:C_0603_1608Metric | C4, C5, C6 |
| 3 | 5.1k | Resistor_SMD:R_0603_1608Metric | R1, R2, R20 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C7, C8 |
| 2 | 5k | Resistor_SMD:R_0603_1608Metric | R18, R19 |
| 2 | SS8050-G | SmartInsolePCB:TRAN_SS8050-G_CIP | Q1, Q2 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R16 |
| 1 | 200k | Resistor_SMD:R_0603_1608Metric | R17 |
| 1 | Conn_01x02_Pin | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J4 |
| 1 | Conn_01x05_Socket | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J2 |
| 1 | Conn_02x10_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J3 |
| 1 | D3V3XA4B10LP | Package_DFN_QFN:Diodes_UDFN-10_1.0x2.5mm_P0.5mm | U1 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U2 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U3 |
| 1 | PJS008U-3000-0 | SmartInsolePCB:PJS008U30000 | J1 |
| 1 | SolderJumper_3_Open | Jumper:SolderJumper-3_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | TLV75801PDRV | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U4 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | JUSB1 |
More from ECE-445/smart-insole
1- 2 layers65.9 × 44 mm

Similar boards
- 4 layers34 × 50 mm

ESP32 Controller
caggieb/ESP32-controller-WIP
Design of an ESP32 based controller with IMU, from PCB to software
36 parts1 - 2 layers

Grad project
Eng-Youssef-Yassin/sos-wearable-device
A wearable safety device for industrial environments. A worker wears a UWB tag; fixed anchor stations track its position in real time and a web dashboard shows where every worker is.
44 parts - 4 layers25.4 × 62.7 mm

- 4 layers26.4 × 56.8 mm

ESP32 Dev module
andresmoreno2702-gif/ESP32-S3-Dev-Board-Project
All KICAD Files and Schematics
26 partsMIT - 2 layers

Esp32 pcb
bobbobdude/AF1_Runiom_Project
I'm thinking that this repo can be a collection of everything we are up to with code, PCB design, 3D models and also general planning.
26 parts - 4 layers25.8 × 63 mm

Custom ESP32 S3 Mini
ChitranshChiranjeev/Custom-ESP32-S3-Mini-PCB-using-KiCad
4-layer ESP32-S3-MINI PCB designed in KiCad with USB Type-C differential routing, LDO power regulation, temperature/humidity sensing, RGB LED, and USB protection circuitry.
26 parts - 4 layers25.5 × 62.8 mm

- 2 layers71.1 × 30.5 mm

Questions
How big is the DesignESP32PCB PCB?
It measures 52.1 × 76.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the DesignESP32PCB use?
50 parts, built around the ESP32-S3-WROOM-1-N8, PJS008U-3000-0, D3V3XA4B10LP and MPU-6050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DesignESP32PCB KiCad files?
From the ECE-445/smart-insole repository on GitHub, at the commit this page was made from: the board is boards/SmartInsolePCB/DesignESP32PCB.kicad_pcb and its schematic boards/SmartInsolePCB/DesignESP32PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the DesignESP32PCB design in my own project?
Its repository states no licence, so its author keeps all rights: ask ECE-445 before reusing the design.