
ESP HI PLUS
dyu134/ESP-HI-PLUS
The Robot sub-module is a high-performance actuator and sensing expansion board for the ESP-HI-PLUS, designed to transform the device into a mobile or interactive robotic platform.

The Robot sub-module is a high-performance actuator and sensing expansion board for the ESP-HI-PLUS, designed to transform the device into a mobile or interactive robotic platform.
Robot is an open-source printed circuit board by dyu134, from the dyu134/ESP-HI-PLUS repository on GitHub. It is a 2-layer board of 70.1 × 100 mm with 86 parts on 149 nets, routed with 783 tracks and 150 vias.
It is built around the RP2040, NINA-B416-00B and W25Q16JVSSIQ, with the MAX40200AUK, AT24CS02-SSHM-B and LSM6DSV16X among its other parts. Its parts include 21 resistors, 18 capacitors, 11 ICs, 8 connectors and 6 diodes. It belongs with the robots and motor control boards and the RP2040 boards of this library.
The Robot sub-module is a high-performance actuator and sensing expansion board for the ESP-HI-PLUS, designed to transform the device into a mobile or interactive robotic platform. Powered by an RP2040 MCU, it handles real-time motor control, battery management, and inertial sensing.
(Space for 3D Model Image)
The Robot module follows the standard ESP-HI-PLUS identification protocol.
| Offset | Size | Field | Value (Hex) | Value (Decoded) | Description |
|---|---|---|---|---|---|
| 0x00 | 4 | Magic Number | 45 53 50 4D | "ESPM" | ASCII sanity check |
| 0x04 | 1 | Class ID | 0x01 | 1 | Actuator - Servo |
| 0x05 | 1 | Module ID | 0x03 | 3 | Robot v1 |
| 0x06 | 1 | HW Revision | 0x01 | 1 | First PCB revision |
| 0x07 | 2 | FW Revision | 0x0100 | 1.0 | Major.Minor |
| 0x09 | 1 | Protocol Revision | 0x01 | 1 | Communication protocol v1 |
| 0x0A | 1 | Power Requirement | 0x00 | Self-powered | Powered by 2S battery |
| 0x0B | 2 | Max Current (mA) | 0x07D0 | 2000 mA | Maximum draw (little-endian) |
| 0x0D | 2 | Min Voltage (mV) | 0x1770 | 6000 mV | Minimum supply voltage (2S) |
| 0x0F | 2 | Boot Delay (ms) | 0x0064 | 100 ms | Power-on delay (little-endian) |
| 0x11 | 4 | Capability Bitmask | 0x00000014 | — | Bits 2, 4 enabled (Async, E-Stop) |
| 0x15 | 16 | Module Name | 52 6F 62 6F... | "Robot" | ASCII, null-terminated |
| 0x25 | 16 | Serial Number | 52 42 2D 30... | "RB-001-XXXX" | ASCII, null-terminated |
| 0x35 | 198 | User Data | — | — | Available for custom data |
| 0xFB | 4 | CRC32 | 0xXXXXXXXX | — | CRC32 of bytes 0x00–0xFA |
Value: 0x00000014
| Bit | Value | Capability | Status |
|---|---|---|---|
| 0 | 0x01 | Needs Calibration | ❌ Disabled |
| 1 | 0x02 | Requires ACK | ❌ Disabled |
| 2 | 0x04 | Async Data | ✅ Enabled |
| 3 | 0x08 | Supports Sleep | ❌ Disabled |
| 4 | 0x10 | Has Emergency Stop | ✅ Enabled |
| 5 | 0x20 | Supports OTA | ❌ Disabled |
| 6 | 0x40 | Has Battery Backup | ❌ Disabled |
| 7 | 0x80 | Requires Bootloader Mode | ❌ Disabled |
The Robot module uses an RP2040 to handle low-level PWM and sensor data. It communicates with the ESP-HI-PLUS main board via UART and I²C.
| Pin | Name | Description |
|---|---|---|
| 1 | VMAIN | 2-way power bus shared with main module |
| 2 | GND | Ground |
| 3 | UART RX | Data from main module |
| 4 | UART TX | Data to main module |
| 5 | EN | Main module control to enable/disable submodule power |
| Pin | Name | Description |
|---|---|---|
| 1 | I2C SDA | For reading module ID metadata EEPROM |
| 2 | I2C SCL | For reading module ID metadata EEPROM |
| 3 | AUX1/ID0 | Hardware class identifier resistor |
| 4 | AUX2 | Auxiliary data pin |
| 5 | AUX3 | Auxiliary data pin |
.
├── Robot.kicad_pro # KiCad project file
├── Robot.kicad_sch # Schematic
├── Robot.kicad_pcb # PCB layout
├── Robot Symbols/ # Project-local schematic symbols
└── README.md # This file| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 0u1 | Capacitor_SMD:C_0402_1005Metric | C3, C5, C6, C7, C10, C12, C13, C17, C18 |
| 6 | MountingHole_Pad_MP | MountIngHole_M3_Slim:MountingHole_M3_Slim | H1, H2, H3, H4, H5, H6 |
| 4 | 100 | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R12, R13, R14, R15 |
| 4 | 10k | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R10, R16, R17, R18 |
| 4 | 1u | Capacitor_SMD:C_0402_1005Metric | C2, C4, C11, C16 |
| 4 | BSMD1812-200-30V | Fuse:Fuse_1812_4532Metric | F2, F3, F4, F5 |
| 4 | MG996R | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | M1, M2, M3, M4 |
| 3 | 150 | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R19, R20, R21 |
| 3 | USBLC6-2P6 | PCM_Package_TO_SOT_SMD_AKL:SOT-666 | D2, D4, D5 |
| 2 | 10u | Capacitor_SMD:C_0402_1005Metric | C14, C15 |
| 2 | 15p | Capacitor_SMD:C_0402_1005Metric | C8, C9 |
| 2 | 1k | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R2, R5 |
| 2 | 4k7 | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R6, R7 |
| 2 | 5k1 | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R3, R4 |
| 2 | Conn_01x10_MountingPin | Connector_FFC-FPC:Hirose_FH12-10S-0.5SH_1x10-1MP_P0.50mm_Horizontal | J7, J8 |
| 2 | MAX40200AUK | Package_TO_SOT_SMD:SOT-23-5 | U2, U5 |
| 2 | PR5L5015-5P-C-H | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J5, J6 |
| 2 | SKRPACE010 | Button_Switch_SMD:SW_Push_1P1T_NO_Vertical_Wuerth_434133025816 | SW1, SW2 |
| 1 | 100m | PCM_Resistor_SMD_AKL:R_1206_3216Metric | R9 |
| 1 | 1M | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R1 |
| 1 | 2920L1000SL21GRG | Fuse:Fuse_2920_7451Metric | F1 |
| 1 | 2S/10C ~1500mAh | Connector_AMASS:AMASS_XT60-F_1x02_P7.20mm_Vertical | BT1 |
| 1 | 4n7 | Capacitor_SMD:C_0402_1005Metric | C1 |
| 1 | 5m | PCM_Resistor_SMD_AKL:R_1206_3216Metric | R8 |
| 1 | 953k | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R11 |
| 1 | ABM8-272-T3 | PCM_Crystal_AKL:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | AT24CS02-SSHM | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U10 |
| 1 | Broadcom_ASMB-KTF0-0A306 | PCM_LED_SMD_AKL:LED_ASMB-KTF0-0A306 | LED1 |
| 1 | INA3221 | Package_DFN_QFN:Texas_RGV0016A_VQFN-16-1EP_4x4mm_P0.65mm_EP2.1x2.1mm | U9 |
| 1 | JST-XH | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J4 |
| 1 | JST-XH | Connector_JST:JST_XH_S3B-XH-A_1x03_P2.50mm_Horizontal | J2 |
| 1 | LSM6DSV16X | LSM6DSV16X:LGA14_LSM6_STM | U7 |
| 1 | MAX17049 | PCM_SparkFun-Semiconductor-Standard:DFN-8_2x2mm_P0.5mm_EP1.2x0.8mm | U6 |
| 1 | NINA-B416 | NINA-B416:NINA_LGA71R_1500X1000X223_PCB | U11 |
| 1 | NTK3139P | PCM_Package_TO_SOT_SMD_AKL:SOT-723 | Q1 |
| 1 | PMEG4010CEJ | PCM_Diode_SMD_AKL:D_SOD-323F | D3 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U3 |
| 1 | SK9822-EC20 | PCM_SparkFun-LED:APA102_2020-6Pin | D1 |
| 1 | TLV75733PDBV | Package_TO_SOT_SMD:SOT-23-5 | U8 |
| 1 | UBEC-5V | UBEC-5V:UBEC-5V | U4 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
| 1 | W25Q16JVSS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U1 |
| 1 | XT60 | Connector_AMASS:AMASS_XT60PW-M_1x02_P7.20mm_Horizontal | J3 |
The 84 most common of 86 parts.

dyu134/ESP-HI-PLUS
The Robot sub-module is a high-performance actuator and sensing expansion board for the ESP-HI-PLUS, designed to transform the device into a mobile or interactive robotic platform.

dyu134/ESP-HI-PLUS
The Robot sub-module is a high-performance actuator and sensing expansion board for the ESP-HI-PLUS, designed to transform the device into a mobile or interactive robotic platform.




ChengminLi/AI-PCB-layout
AI agent skill for designing and reviewing power-electronics PCBs, with a human review gate after every step


yesnoj/FilMachine_Reworked
FilMachine is an automated film processing machine designed for photographic film development. It handles the entire process: chemical baths, water rinses, temperature regulation, and motor-driven film agitation — all…


It measures 70.1 × 100 mm and has 2 copper layers, 1.6 mm thick.
86 parts, built around the RP2040, NINA-B416-00B, W25Q16JVSSIQ and MAX40200AUK. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the dyu134/ESP-HI-PLUS repository on GitHub, at the commit this page was made from: the board is Sub-modules/Robot/Robot.kicad_pcb and its schematic ESP-HI-PLUS.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask dyu134 before reusing the design.