
Robot
dyu134/ESP-HI-PLUS
The Robot sub-module is a high-performance actuator and sensing expansion board for the ESP-HI-PLUS, designed to transform the device into a mobile or interactive robotic platform.

The Robot sub-module is a high-performance actuator and sensing expansion board for the ESP-HI-PLUS, designed to transform the device into a mobile or interactive robotic platform.
ESP HI PLUS is an open-source printed circuit board by dyu134, from the dyu134/ESP-HI-PLUS repository on GitHub. It is a 4-layer board of 58 × 35 mm with 88 parts on 87 nets, routed with 656 tracks and 118 vias.
It is built around the ESP32-S3-WROOM-1-N8, MAX40200AUK and LSM6DSV16X, with the TLV75733PDBV, BAT54S and USBLC6-2P6 among its other parts. Its parts include 32 resistors, 19 capacitors, 11 diodes, 7 ICs and 5 connectors. It belongs with the robots and motor control boards and the ESP32 boards of this library.
The Robot sub-module is a high-performance actuator and sensing expansion board for the ESP-HI-PLUS, designed to transform the device into a mobile or interactive robotic platform. Powered by an RP2040 MCU, it handles real-time motor control, battery management, and inertial sensing.
(Space for 3D Model Image)
The Robot module follows the standard ESP-HI-PLUS identification protocol.
| Offset | Size | Field | Value (Hex) | Value (Decoded) | Description |
|---|---|---|---|---|---|
| 0x00 | 4 | Magic Number | 45 53 50 4D | "ESPM" | ASCII sanity check |
| 0x04 | 1 | Class ID | 0x01 | 1 | Actuator - Servo |
| 0x05 | 1 | Module ID | 0x03 | 3 | Robot v1 |
| 0x06 | 1 | HW Revision | 0x01 | 1 | First PCB revision |
| 0x07 | 2 | FW Revision | 0x0100 | 1.0 | Major.Minor |
| 0x09 | 1 | Protocol Revision | 0x01 | 1 | Communication protocol v1 |
| 0x0A | 1 | Power Requirement | 0x00 | Self-powered | Powered by 2S battery |
| 0x0B | 2 | Max Current (mA) | 0x07D0 | 2000 mA | Maximum draw (little-endian) |
| 0x0D | 2 | Min Voltage (mV) | 0x1770 | 6000 mV | Minimum supply voltage (2S) |
| 0x0F | 2 | Boot Delay (ms) | 0x0064 | 100 ms | Power-on delay (little-endian) |
| 0x11 | 4 | Capability Bitmask | 0x00000014 | — | Bits 2, 4 enabled (Async, E-Stop) |
| 0x15 | 16 | Module Name | 52 6F 62 6F... | "Robot" | ASCII, null-terminated |
| 0x25 | 16 | Serial Number | 52 42 2D 30... | "RB-001-XXXX" | ASCII, null-terminated |
| 0x35 | 198 | User Data | — | — | Available for custom data |
| 0xFB | 4 | CRC32 | 0xXXXXXXXX | — | CRC32 of bytes 0x00–0xFA |
Value: 0x00000014
| Bit | Value | Capability | Status |
|---|---|---|---|
| 0 | 0x01 | Needs Calibration | ❌ Disabled |
| 1 | 0x02 | Requires ACK | ❌ Disabled |
| 2 | 0x04 | Async Data | ✅ Enabled |
| 3 | 0x08 | Supports Sleep | ❌ Disabled |
| 4 | 0x10 | Has Emergency Stop | ✅ Enabled |
| 5 | 0x20 | Supports OTA | ❌ Disabled |
| 6 | 0x40 | Has Battery Backup | ❌ Disabled |
| 7 | 0x80 | Requires Bootloader Mode | ❌ Disabled |
The Robot module uses an RP2040 to handle low-level PWM and sensor data. It communicates with the ESP-HI-PLUS main board via UART and I²C.
| Pin | Name | Description |
|---|---|---|
| 1 | VMAIN | 2-way power bus shared with main module |
| 2 | GND | Ground |
| 3 | UART RX | Data from main module |
| 4 | UART TX | Data to main module |
| 5 | EN | Main module control to enable/disable submodule power |
| Pin | Name | Description |
|---|---|---|
| 1 | I2C SDA | For reading module ID metadata EEPROM |
| 2 | I2C SCL | For reading module ID metadata EEPROM |
| 3 | AUX1/ID0 | Hardware class identifier resistor |
| 4 | AUX2 | Auxiliary data pin |
| 5 | AUX3 | Auxiliary data pin |
.
├── Robot.kicad_pro # KiCad project file
├── Robot.kicad_sch # Schematic
├── Robot.kicad_pcb # PCB layout
├── Robot Symbols/ # Project-local schematic symbols
└── README.md # This file| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 0u1 | Capacitor_SMD:C_0402_1005Metric | C7, C8, C9, C11, C13, C15, C16, C17, C18 |
| 7 | 10k | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R1, R2, R13, R30, R31, R32, R33 |
| 6 | 10u | Capacitor_SMD:C_0402_1005Metric | C3, C4, C5, C6, C10, C14 |
| 6 | 5k1 | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R3, R4, R5, R6, R10, R11 |
| 5 | 100k | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R7, R12, R21, R23, R25 |
| 4 | 100 | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R17, R18, R19, R20 |
| 4 | MountingHole_Pad_MP | MountIngHole_M3_Slim:MountingHole_M3_Slim | H1, H2, H3, H4 |
| 3 | 33k | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R22, R24, R26 |
| 3 | BAT54S | Package_TO_SOT_SMD:SOT-23 | D9, D10, D11 |
| 3 | USBLC6-2P6 | PCM_Package_TO_SOT_SMD_AKL:SOT-666 | D1, D7, D8 |
| 2 | 3k3 | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R8, R9 |
| 2 | 47k | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R28, R29 |
| 2 | MAX40200AUK | Package_TO_SOT_SMD:SOT-23-5 | U1, U6 |
| 2 | PR5L4015-5P-C-F | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J3, J4 |
| 2 | SKRPACE010 | Button_Switch_SMD:SW_Push_1P1T_NO_Vertical_Wuerth_434133025816 | SW1, SW2 |
| 1 | 100u | Capacitor_SMD:C_0805_2012Metric | C12 |
| 1 | 15p | Capacitor_SMD:C_0402_1005Metric | C1 |
| 1 | 1M | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R27 |
| 1 | 1u | Capacitor_SMD:C_0402_1005Metric | C2 |
| 1 | 2" IPS LCD | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J2 |
| 1 | 2k1 | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R14 |
| 1 | 4n7 | Capacitor_SMD:C_0402_1005Metric | C19 |
| 1 | 634k | PCM_Resistor_SMD_AKL:R_0402_1005Metric | R15 |
| 1 | AO3401A | PCM_Package_TO_SOT_SMD_AKL:SOT-23 | Q1 |
| 1 | Battery_Cell | Connector_Molex:Molex_PicoBlade_53048-0210_1x02_P1.25mm_Horizontal | BT1 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U2 |
| 1 | ICS-43434 | Sensor_Audio:InvenSense_ICS-43434-6_3.5x2.65mm | MK1 |
| 1 | JS102011SAQN | Button_Switch_SMD:SW_SPDT_CK_JS102011SAQN | SW3 |
| 1 | LSM6DSV16X | LSM6DSV16X:LGA14_LSM6_STM | U8 |
| 1 | MAX98357A | Package_DFN_QFN:TQFN-16-1EP_3x3mm_P0.5mm_EP1.23x1.23mm | U7 |
| 1 | MF-MSMF200 | Fuse:Fuse_1812_4532Metric | F1 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Hirose_DM3AT-SF-PEJM5 | J5 |
| 1 | NTK3139P | PCM_Package_TO_SOT_SMD_AKL:SOT-723 | Q2 |
| 1 | ORANGE | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | PMEG4010CEJ | PCM_Diode_SMD_AKL:D_SOD-323F | D5 |
| 1 | RED | LED_SMD:LED_0603_1608Metric | D4 |
| 1 | SMF6.8CA | PCM_Diode_SMD_AKL:D_SOD-123F | D6 |
| 1 | Speaker | Connector_Molex:Molex_PicoBlade_53048-0210_1x02_P1.25mm_Horizontal | LS1 |
| 1 | TLV75733PDBV | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | TP4065 | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U5 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
| 1 | Val** | PCM_SparkFun-Aesthetic:OSHW_Logo_5mm | Ref** |
| 1 | WS2812B-2020 | LED_SMD:LED_WS2812B-2020_PLCC4_2.0x2.0mm | D12 |

dyu134/ESP-HI-PLUS
The Robot sub-module is a high-performance actuator and sensing expansion board for the ESP-HI-PLUS, designed to transform the device into a mobile or interactive robotic platform.

dyu134/ESP-HI-PLUS
The Robot sub-module is a high-performance actuator and sensing expansion board for the ESP-HI-PLUS, designed to transform the device into a mobile or interactive robotic platform.
GeneralSyb/Sagittarius-Headtracker
Project files for the Sagittarius S1 Prototype


Jan-Philipp-Munsch/kartonaut
TVC model rocket (after BPS.space Scout F): Teensy 4.1 flight firmware, mainboard spec, project log

gallicchio/AMOD-and-RFMOD
The tutorial's 2x12 adapter (/mudd/133electronics/icepi-zero-dac-adc/adapterboard/) with a 2 x 6 right-angle Pmod socket on a 15 mm extension of its right-hand end, so an Icepi Zero can drive AMOD-A's and RF-MOD's Pmod…



sneakylizard123-4/STM32H743
This board puts an STM32H743XIH6 and an iCE40 UP5K on the same PCB. The H743 handles control, USB, Ethernet, storage, and audio.

FBIopeningUPP/ChromaDeck
ChromaDeck is a massive, open-source, fully custom USB MIDI Control Surface designed for streaming, video editing, and live audio mixing.
It measures 58 × 35 mm and has 4 copper layers, 1.6 mm thick.
88 parts, built around the ESP32-S3-WROOM-1-N8, MAX40200AUK, LSM6DSV16X and TLV75733PDBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the dyu134/ESP-HI-PLUS repository on GitHub, at the commit this page was made from: the board is ESP-HI-PLUS.kicad_pcb and its schematic ESP-HI-PLUS.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask dyu134 before reusing the design.