Skip to the content
2 layers41 × 17.4 mmAmp and switch, the printed circuit board in 3D

This project is a collection of schematics and pcb layouts for adding Bluetooth or Line input to an "ole toob" radio.

Size
41 × 17.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
30
Nets
26
Pads
82
Tracks, vias
164, 16
Pours
1
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
16 Sep 2019
Updated
27 Oct 2020

Overview

Amp and switch is an open-source printed circuit board by dwilliams, from the dwilliams/ole-radio-input-switch repository on GitHub, published under the BSD-2-Clause licence. It is a 2-layer board of 41 × 17.4 mm with 30 parts on 26 nets, routed with 164 tracks and 16 vias.

It is built around the LM324. Its parts include 14 resistors, 5 connectors, 4 capacitors, 4 transistors and 1 IC. It belongs with the audio and music boards of this library.

Main components

1

README

README.md

ole-radio-input-switch

This project is a collection of schematics and pcb layouts for adding Bluetooth or Line input to an "ole toob" radio. One key feature of this project is keeping the radio functional, unlike those "strip the chassis and use a cheap Bluetooth and amplifier" abominations.

Theory of Operation

...

Bluetooth Module Data

Pinout (Copied from Amazon listing: https://www.amazon.com/gp/product/B07RRW8373):

  1. +5V power supply: connect the positive pole of the power supply, the voltage range is 4.2V~5V, please ensure that the power supply is within this range. Exceeding this range may damage the module or cause the work to be abnormal.
  2. Ground: GND is connected to the negative pole of the power supply.
  3. left channel: connect the left channel input of the power amplifier board, or the left channel of the earphone, it is recommended to connect a capacitor to the output port (depending on the input matched by the power amplifier).
  4. right channel: connect the right channel input of the power amplifier board, or the right channel of the earphone, it is recommended to connect a capacitor to the output port (depending on the matching input of the power amplifier).
  5. Silent output port: The port is preset to a high level, and the port outputs a low level when muted.
  6. Status indicator: When the Bluetooth is not connected, the light flashes quickly, and once the Bluetooth connection is successful, it will flash slowly.
  7. Reserved port: The port has been pulled up to 5V. When the port is triggered by a low level, it will be turned off. When the port is turned back to the low level again.

Parts

30
QtyValueFootprintReferences
71KResistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolderR1, R2, R5, R6, R9, R10, R11
4100 nFCapacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolderC1, C2, C3, C4
43KResistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolderR12, R13, R14, R15
4Q_NMOS_GSDPackage_TO_SOT_SMD:SOT-23_HandsolderingQ1, Q2, Q3, Q4
320KResistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolderR7, R8, R16
210KPotentiometer_SMD:Potentiometer_Bourns_TC33X_VerticalRV1, RV2
2Conn_01x01Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_VerticalJ2, J5
1Conn_01x03Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ4
1Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ3
1Conn_01x05Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalJ1
1LM324Package_SO:SOIC-14_3.9x8.7mm_P1.27mmU1

More from dwilliams/ole-radio-input-switch

2
  • 2 layers27.2 × 18.5 mmPower board-12v, the printed circuit board in 3D

    Power board-12v

    dwilliams/ole-radio-input-switch

    This project is a collection of schematics and pcb layouts for adding Bluetooth or Line input to an "ole toob" radio.

    15 parts1BSD-2-Clause
  • 2 layers40 × 45 mmPower board-120vac, the printed circuit board in 3D

    Power board-120vac

    dwilliams/ole-radio-input-switch

    This project is a collection of schematics and pcb layouts for adding Bluetooth or Line input to an "ole toob" radio.

    11 parts1BSD-2-Clause

Similar boards

  • 4 layers99 × 53.3 mmPSLab, the printed circuit board in 3D

    PSLab

    fossasia/pslab-hardware

    PSLab Hardware Design and Schematics https://pslab.io

    199 parts1.7kApache-2.0
  • 2 layers36.8 × 34.7 mmTinylab proto1, the printed circuit board in 3D

    Tinylab proto1

    espotek-org/Labrador

    EspoTek Labrador is a USB device that transforms your PC or smartphone into a fully-featured electronics lab. This repo holds all of the source code!

    79 parts1.2k
  • 4 layers82.6 × 82.5 mmJumperless2, the printed circuit board in 3D

    Jumperless2

    Architeuthis-Flux/Jumperless

    A jumperless breadboard

    208 parts914
  • 2 layers231.1 × 106.7 mmSnark barker, the printed circuit board in 3D

    Snark barker

    schlae/snark-barker

    A 100% compatible replica of the famed SB 1.0 sound card

    199 parts687
  • 4 layers82.6 × 82.6 mmJumperlessV5r8, the printed circuit board in 3D

    JumperlessV5r8

    Architeuthis-Flux/JumperlessV5

    The next generation jumperless breadboard

    650 parts332
  • 4 layers72.4 × 95.3 mmDingoPDM, the printed circuit board in 3D

    DingoPDM

    corygrant/dingoPDM

    Hardware - dingoPDM is an open source, affordable automotive PDM (Power Distribution Module). Pre-assembled and tested units are available or the design can be used to build a DIY version.

    156 parts128MIT
  • 2 layers191.5 × 76 mmPcb project, the printed circuit board in 3D

    Pcb project

    CrashOverride85/zc95

    4 channel EStim box inspired by the mk312bt, with Lua scripting support

    337 parts117GPL-3.0
  • 4 layers292.1 × 88.3 mmSnark barker mca, the printed circuit board in 3D

    Snark barker mca

    schlae/snark-barker-mca

    A Sound Blaster compatible sound card for Micro Channel bus computers

    177 parts69

Questions

How big is the Amp and switch PCB?

It measures 41 × 17.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Amp and switch use?

30 parts, built around the LM324. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Amp and switch KiCad files?

From the dwilliams/ole-radio-input-switch repository on GitHub, at the commit this page was made from: the board is amp-and-switch/amp-and-switch.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Amp and switch design in my own project?

Its repository publishes it under the BSD-2-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).