Skip to the content
4 layers52 × 94.2 mmTangara mainboard, the printed circuit board in 3D

Tangara mainboard

dpaola2/Harmony

Current logistics, September 26: core modules are received, and the revision B shells, LCD supports and carrier gauge passed loose fit checks. Screws and foam are ordered. The SD trial playlist is prepared.

Size
52 × 94.2 mm
Copper layers
4
Thickness
1.6 mm
Parts
124
Nets
127
Pads
570
Tracks, vias
898, 499
Pours
44
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
22 Nov 2025
Updated
4 Oct 2026

Overview

Tangara mainboard is an open-source printed circuit board by dpaola2, from the dpaola2/Harmony repository on GitHub. It is a 4-layer board of 52 × 94.2 mm with 124 parts on 127 nets, routed with 898 tracks and 499 vias.

It is built around the ATSAMD21E18A-AF, ESP32-WROVER-E-N16R8 and INA1620RTWR, with the PCA8575BS, TPS65133DPD and WM8523GEDT/R among its other parts. Its parts include 35 resistors, 33 capacitors, 13 ICs, 7 connectors and 3 transistors. It belongs with the computers and single-board computers boards and the ESP32 and SAM D and SAM boards of this library.

Main components

12

README

hardware/mark-6/carrier-rev-a/README.md

Harmony Mark-6 carrier, revision A

Current logistics, September 26: core modules are received, and the revision B shells, LCD supports and carrier gauge passed loose fit checks. Screws and foam are ordered. The SD trial playlist is prepared. The assembled carrier remains unordered. A supplier quote request was sent to PCBWay for DFM review and pricing; the response is pending. Physical mating, cable mapping and powered qualification remain open. The historical design record below retains its original dated assumptions.

September 22 display update: Waveshare 29318 (ST7796S) replaces unavailable Adafruit #5846. PiShop.us lists it in stock at $24.95. The sourcing and compatibility review, hollow prototype and firmware now use this module. The carrier electrical nets are unchanged. Manufacturing remains review-only.

Updated September 22, 2026. HARMONY-17. Routed prototype design; manufacturing review package, not an order release.

Dave printed and accepted the 74 x 178 x 28 mm size dummy. The component stack now uses the actual Feather and ANO 3D models, specified sockets and an antenna cutout. The routed four-layer PCB passes KiCad DRC with zero violations and zero unconnected nets. The independent PCB audit matches 122 electrical pads to the schematic and all 28 Feather mating coordinates to vendor CAD. The schematic also passes ERC.

The assembly readiness review records the corrected ENIG metadata, part/placement audit and the documented U1 thermal-hole DRC warning.

Start with the design review, editable PCB, schematic, and manufacturing review package. Mechanical review, power review and machine-readable verification document the checks and their limits. No order has been placed.

USB-only operation remains adopted. Battery space is reserved for Mark 8. The accepted size dummy proves the outside dimensions work for Dave; physical display fit, header insertion and cable access still require a trial assembly. The revised prototype uses the Waveshare vendor STEP, including rear connectors.

Dave adopted a 3.5-inch display and separate display/storage buses. The carrier will arrive assembled, including its sockets and connectors. Dave plugs in a factory-headered ESP32 Feather V2 (#5900), a display ribbon cable and the controls cable. No hand soldering is part of the intended assembly.

Parts and interfaces

Bluetooth verification: the live DigiKey cart contains four Adafruit #5900, DigiKey 1528-5900-ND. Adafruit's Feather V2 schematic identifies X3 as ESP32-PICO-MINI-02, containing ESP32-PICO-V3-02. This original ESP32 supports Bluetooth 4.2 BR/EDR (Classic) and BLE; it meets the radio requirement for A2DP source streaming. Adafruit #5900 explicitly specifies Classic/LE, and Espressif's module datasheet confirms BR/EDR. ESP-IDF's A2DP source example documents audio transmission. This verifies specifications, not a physical playback test on the new Feather. Keep this exact Classic-capable model in the BOM; a BLE-only ESP32-family substitution does not satisfy the requirement.

FunctionDraft implementationStatus
Processor and BluetoothAdafruit ESP32 Feather V2 #5900 in carrier socketsFour in DigiKey cart; not purchased
DisplayWaveshare 29318 3.5-inch IPS, via 18-pin ribbonGlass 61.00 x 92.44 mm; PiShop.us lists in stock
StorageHirose DM3AT-SF-PEJM5 microSD socket on carrierPin and footprint pad sets checked
ControlsPreviously ordered assembled ANO I2C control board50 mm QT-to-QT cable; nominal stack checked
PowerUSB-C through Feather; TPS62162 3.3 V peripheral supplyUSB budget reviewed; physical startup/load/thermal qualification remains

The EYESPI breakout replaces the proposed FeatherWing connection so that the carrier can assign display and storage to separate SPI hosts. Its onboard SD socket stays unused. Capacitive touch on Waveshare 29318 is incidental; the interface still uses physical controls.

Proposed GPIO assignment

These are ESP32 GPIO numbers, not generic Feather pin numbers. Header references below use the numbering in Adafruit's Feather V2 Eagle files. They are for schematic development, not a breadboard wiring instruction.

SignalGPIOFeather headerDestination
SD clock5JP1.6Carrier SD CLK
SD MOSI19JP1.5Carrier SD CMD
SD MISO21JP1.4Carrier SD DAT0
SD select25JP1.11Carrier SD DAT3
Display clock14JP3.10EYESPI 4
Display MOSI27JP3.6EYESPI 5
Display select26JP1.12EYESPI 9
Display command/data33JP3.7EYESPI 7
Display reset32JP3.9EYESPI 8
Display backlight control4JP1.7EYESPI 2
Controls I2C clock20JP3.11Controls SCL
Controls I2C data22JP3.12Controls SDA
Peripheral power-good input34JP1.10TPS62162 PG

Use SPI3 for SD and SPI2 for display in native ESP-IDF. The allocation does not reuse signal GPIOs. A 47k pull-up reinforces GPIO5's normal high boot strap; the SD clock destination is an input. GPIO12 and GPIO15 stay unused. Display MISO and touch are unused. The display-side SD select is held high. The Waveshare display uses SPI without jumper soldering. GPIO34 reads peripheral power-good before firmware starts I/O.

Power, parts and mechanics

The exact carrier component choices are in bom-draft.csv; the grouped assembler BOM is output/manufacturing-review/assembly-bom.csv. Both sockets and every connector must be fitted by the assembler. F1 is a 0.75 A-hold Bourns PTC, with 0.52 A hold at 60 C. The regulator uses 2.2 uH and 22 uF input/output bulk capacitors. The power review gives the source budget, limits and staged first-power procedure.

The mechanical review records the 6.5 mm carrier height, 12 mm ANO spacers, cable orientation and case-port requirements. The vendor 3D model yields 0.88 mm nominal clearance above the Feather beneath a 1.6 mm front wall. Display geometry uses the Waveshare vendor STEP. The detailed assembly is in output/mechanical/; it is a review model, not the final hollow housing.

The carrier cutout removes board material beneath the antenna. Ground pours avoid the 15 mm halo, while unavoidable header copper remains inside part of it. The finished device still needs an RF test. Vias inside SMT pads require filled, copper-capped construction and assembler stencil review. The release conditions are listed in the manufacturing package.

build_pcb.py creates the initial placement; routing.ses is the saved routing result. routed-base.kicad_pcb preserves its imported state. finish_pcb.py loads that base, completes the remaining routes, adjusts edge clearance and fills ground planes. verify_pcb.py checks the final board against the exported schematic netlist. Run it with KiCad's bundled Python after generating a fresh final-drc.json.

Evidence and limits

Mark-5 SD reads provoked clicks in its local VS1053 analog output; RAM-only playback was clean. That did not establish shared SPI as the cause. Separate buses reduce contention; they do not prove clean playback or replace power layout work. Mark-6 must still demonstrate display refresh during Bluetooth playback, controls, reconnection and the deferred full-album run.

Vendor Feather, display, ANO and EYESPI CAD, licenses and source hashes are preserved in reference/. Passive socket symbols do not model the ESP32's electrical limits, so a clean ERC alone cannot establish GPIO compatibility. The netlist checks explicitly verify the connector mapping and supply separation; bench and RF tests remain. The previous WROVER wiring is suspended after two reported board failures; their root cause remains unknown.

Sources and cross-references

Parts

124
QtyValueFootprintReferences
2510kΩResistor_SMD:R_0603_1608MetricR1, R2, R4, R10, R11, R12, R21, R22, R26, R30, R31, R32, R34, R35, R37, R38 +9
1110μFCapacitor_SMD:C_0805_2012MetricC1, C2, C3, C7, C18, C24, C25, C27, C32, C35, C42
90.1μFCapacitor_SMD:C_0603_1608MetricC9, C13, C14, C30, C31, C34, C37, C39, C40
7LOGOfootprints:star_smallG***, G***, G***, G***, G***, G***, G***
51μFCapacitor_SMD:C_0805_2012MetricC4, C12, C23, C33, C41
41MΩResistor_SMD:R_0603_1608MetricR7, R50, R51, R56
4MountingHolefootprints:MountingHole_2.2mm_M2_Pad_Via2H1, H2, H3, H4
322μFCapacitor_SMD:C_1206_3216MetricC10, C16, C38
2100pFCapacitor_SMD:C_0603_1608MetricC17, C19
21kΩResistor_SMD:R_0603_1608MetricR39, R42
22.2kΩResistor_SMD:R_0805_2012MetricR3, R8
22700pFCapacitor_SMD:C_0603_1608MetricC6, C15
24.7μHInductor_SMD:L_1008_2520MetricL1, L2
2560ΩResistor_SMD:R_0805_2012MetricR6, R15
2LOGOfootprints:sparklesG***, G***
2PJC138KPackage_TO_SOT_SMD:SOT-323_SC-70Q2, Q3
2SW_Pushfootprints:SW_EVQ-P4HB3BSW2, SW3
1+5VTestPoint:TestPoint_Pad_D1.0mmTP3
1-5VTestPoint:TestPoint_Pad_D1.0mmTP4
1100uFCapacitor_SMD:C_1210_3225MetricC29
174CBTLV3257Package_SO:TSSOP-16_4.4x5mm_P0.65mmU14
1AMP_ENTestPoint:TestPoint_Pad_D1.0mmTP5
1AMP_MUTETestPoint:TestPoint_Pad_D1.0mmTP6
1ATSAMD21E18A-AFPackage_QFP:TQFP-32_7x7mm_P0.8mmU13
1BATTestPoint:TestPoint_Pad_D1.0mmTP7
1BAT54CPackage_TO_SOT_SMD:SOT-23D4
1BD91N01NUXfootprints:BD91N01NUX-E2U12
1BatteryConnector_JST:JST_PH_S3B-PH-K_1x03_P2.00mm_HorizontalJ7
1D5V0L2B3T-7Package_TO_SOT_SMD:SOT-523U3
1ESP32-WROVER-Efootprints:ESP32-WROVERU15
1FP Connectorfootprints:G-Switch GT-F0509SR15-15SMT01J2
1INA1620Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.7x2.7mm_ThermalViasU1
1JTAGConnector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMDJ3
1LOGOfootprints:heartG***
1LOGOfootprints:oshwa-certG***
1LOGOLOGOG***
1LOGOfootprints:starG***
1MCP73871footprints:QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm_ThermalVias2U10
1PCA8575Package_DFN_QFN:HVQFN-24-1EP_4x4mm_P0.5mm_EP2.1x2.1mmU9
1PE1605C4A6Package_TO_SOT_SMD:SOT-23-6U5
1PMV48XPA2RPackage_TO_SOT_SMD:TSOT-23Q1
1SD_CardConnector_Card:SD_Hirose_DM1AA_SF_PEJ82J4
1SJ-3506-SMTfootprints:CUI_SJ-3506-SMTJ1
1SWDfootprints:SAMDSWDJ5
1SW_SPDTButton_Switch_SMD:SW_SPDT_CK-JS102011SAQNSW1
1TLV75533PDBVPackage_TO_SOT_SMD:SOT-23-5U4
1TPS22948footprints:SOT65P210X110-6NU16
1TPS65133footprints:SON40P300X300X80-13NU7
1USBfootprints:GCT_USB4510-03-1-A_REVAJ6
1WM8523Package_SO:SSOP-20_4.4x6.5mm_P0.65mmU17

The 119 most common of 124 parts.

More from dpaola2/Harmony

1
  • 4 layers66.2 × 169 mmHarmony mark6-carrier, the printed circuit board in 3D

    Harmony mark6-carrier

    dpaola2/Harmony

    Current logistics, September 26: core modules are received, and the revision B shells, LCD supports and carrier gauge passed loose fit checks. Screws and foam are ordered. The SD trial playlist is prepared.

    52 parts

Similar boards

  • 4 layers79.9 × 65.2 mmEthernet Dev Board, the printed circuit board in 3D

    Ethernet Dev Board

    ResonanceGroup/ESP32_Ethernet_Dev_Board

    Small dev board for the ESP32 that is meant to incorporate ethernet controller for testing

    116 partsMIT
  • 4 layers90 × 47 mmPICkit, the printed circuit board in 3D

    PICkit

    VoxelTek/PICkit

    119 parts
  • 4 layers110 × 70 mmAD4030-Voltage, the printed circuit board in 3D

    AD4030-Voltage

    BehrensG/ARTY_Z7

    Repository with test projects to learn Zynq 7000 SoC.

    192 parts1
  • 2 layers27.5 × 41.5 mmXmas orn, the printed circuit board in 3D

    Xmas orn

    MRobertEvers/esp32-xmas

    ESP32 xmas display

    20 parts
  • 4 layers100 × 100 mmInputSwitch, the printed circuit board in 3D

    InputSwitch

    smileym4n-collab/Kicadprojects

    109 parts
  • 4 layers40 × 22 mmRgba, the printed circuit board in 3D

    Rgba

    fu5ha/rgba

    Reasonably Good Bluetooth Audio - A tiny, inline Bluetooth audio receiver for IEMs.

    73 parts8
  • 2 layers36 × 16 mmMcp2518fd, the printed circuit board in 3D

    Mcp2518fd

    dragonlock2/kicadboards

    Offsite backup for the miscellaneous KiCad boards that don't fit elsewhere

    21 parts14Apache-2.0

Questions

How big is the Tangara mainboard PCB?

It measures 52 × 94.2 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Tangara mainboard use?

124 parts, built around the ATSAMD21E18A-AF, ESP32-WROVER-E-N16R8, INA1620RTWR and PCA8575BS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Tangara mainboard KiCad files?

From the dpaola2/Harmony repository on GitHub, at the commit this page was made from: the board is hardware/reviews/harmony-r3/mainboard-experiment/tangara-mainboard.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Tangara mainboard design in my own project?

Its repository states no licence, so its author keeps all rights: ask dpaola2 before reusing the design.