Skip to the content
2 layersDsbi, the printed circuit board in 3D

Damn Simple Brainwave Interface

Copper layers
2
Thickness
1.6 mm
Parts
20
Nets
14
Pads
54
Tracks, vias
0, 8
Routed
Not yet
KiCad
KiCad 7 (file 20221018)
Created
17 Sep 2023
Updated
11 Aug 2026

Overview

Dsbi is an open-source printed circuit board by donarturo11, from the donarturo11/dsbi repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board with 20 parts on 14 nets.

It is built around the TL082. Its parts include 10 resistors, 6 capacitors, 2 ICs and 2 connectors. It belongs with the interfaces and adapters boards of this library.

Main components

1

README

README.md

dsbi

(Damn Simple Brainwave Interface)

This is simple and modular interface for EEG acquisition. Analog part is brought from BioAmpExg. The goal of this project is easy assemblation by everyone with very small experience in electronics. Circuit was tested with ESP32 and AVR Attiny13.

Data format

Data are sent as raw unsigned 12-bit integer wave with sample rate 512 Hz in following format:

text
unsigned short meteredValue = HHHH HHLL LLLL
unsigned char firstByte  = 10HH HHHH # ( 0x80 | ( (meteredValue >> 6) & 0x3F) )
unsigned char secondByte = 01LL LLLL # ( 0x40 |   (meteredValue & 0x3F) )

Specs

Common:

  • Interface: UART
  • Sample rate 512 Hz
  • Raw wave 12-bit unsigned short

ESP32

  • Sampling in 12-bit without oversampling
  • Hardware UART 8-N-1
  • Baudrate: 38400

Attiny13

  • Sampling in 10 bit with oversampling
  • Software UART 8-N-2
  • Baudrate: 19200

Compatible software

Parts

20
QtyValueFootprintReferences
410kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1, R2, R3, R8
41kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR4, R5, R7, R9
2TL082Package_DIP:DIP-8_W7.62mm_SocketU1, U2
2~Connector:FanPinHeader_1x03_P2.54mm_VerticalJ1, J2
1100nCapacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mmC4
1100uCapacitor_THT:CP_Radial_D8.0mm_P5.00mmC6
110RResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR6
1220nCapacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mmC1
12M2Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR10
12n2Capacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mmC2
147nCapacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mmC5
147uCapacitor_THT:CP_Radial_D8.0mm_P5.00mmC3

Similar boards

  • 4 layers99 × 53.3 mmPSLab, the printed circuit board in 3D

    PSLab

    fossasia/pslab-hardware

    PSLab Hardware Design and Schematics https://pslab.io

    199 parts1.7kApache-2.0
  • 2 layers82.1 × 82.1 mmUncut Gem, the printed circuit board in 3D

    Uncut Gem

    QuantumVillage/UncutGem

    A prototype Full Stack fully Open Source NV Center Diamond Magnetometer

    207 parts210AGPL-3.0
  • 2 layers96.8 × 97 mmPsoc5power, the printed circuit board in 3D

    Psoc5power

    profdc9/DRSSTC-PCB-Pack

    A pack of PCBs for a dual resonant solid state tesla coil setup. Pretty much everything you need.

    133 parts59
  • 2 layers130.6 × 112 mmSWN, the printed circuit board in 3D

    SWN

    4ms/SWN

    Spherical Wavetable Navigator source code

    614 parts43
  • 2 layers48 × 36.5 mmOsillyscope etchable, the printed circuit board in 3D

    Osillyscope etchable

    tvlad1234/osillyscope

    Low cost, low part count CH32V003-based oscilloscope

    31 parts30MIT
  • 2 layers60 × 50 mmEurorack volca, the printed circuit board in 3D

    Eurorack volca

    grappendorf/eurorack-volca

    Mounting Korg Volcas into a Eurorack system

    25 parts19
  • 2 layers79 × 107 mmEurorack spinfx, the printed circuit board in 3D

    Eurorack spinfx

    grappendorf/eurorack-spinfx

    Spin FV-1 based effects module for Eurorack systems

    80 parts16
  • 2 layers167.8 × 200.6 mmRandom Jazz Generator, the printed circuit board in 3D

    Random Jazz Generator

    telec16/modular-synth

    Little side project, don't expect much updates.

    132 parts16

Questions

What parts does the Dsbi use?

20 parts, built around the TL082. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Dsbi KiCad files?

From the donarturo11/dsbi repository on GitHub, at the commit this page was made from: the board is hardware/dsbi.kicad_pcb and its schematic hardware/dsbi.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Dsbi design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).