Skip to the content
2 layers99.1 × 45.4 mmKa3005p displaydriver, the printed circuit board in 3D

Ka3005p displaydriver

djedditt/ka3005p-display10

This repository contains a KiCad project for a Korad KA3005P display driver, included are the schematic, pcb layout and gerber files.

Size
99.1 × 45.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
47
Nets
57
Pads
155
Tracks, vias
362, 59
Pours
3
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
9 Oct 2020
Updated
9 Oct 2020

Overview

Ka3005p displaydriver is an open-source printed circuit board by djedditt, from the djedditt/ka3005p-display repository on GitHub, published under the CC-BY-4.0 licence. It is a 2-layer board of 99.1 × 45.4 mm with 47 parts on 57 nets, routed with 362 tracks and 59 vias.

It is built around the 74HC595 and MMBT3904. Its parts include 21 resistors, 12 diodes, 5 transistors, 3 ICs and 1 capacitor. It belongs with the lEDs and displays boards of this library.

Main components

2

README

README.md

ka3005p-display

This repository contains a KiCad project for a Korad KA3005P display driver, included are the schematic, pcb layout and gerber files. This board can replace the existing KA002_V3.x PCB in a Korad KA3005P (or KA3005D) power supply.

Table of Contents

Bill of Materials (BOM)

Below you'll find the bill of materials for this board. The original PCB comes with 4.0mm LEDs, but I went for 5.0mm because those are more readily available.

IDDesignatorDescriptionQuantity
1C1Capacitor, Ceramic, 22uF, 25V, 10%, X7R, 08051
2LED1, LED24-Digit 7-Segment LED Display, Red, Common Cathode, TH, 0.40"2
3R17, R18, R19, R20, R21Resistor, 1k Ohm, 1%, 1/8 W, 08055
4Q4, Q5, Q6, Q7, Q8NPN Transistor, MMBT3904, SOT-23-35
5D1, D2, D3, D4, D5, D6, D7, D8, D9, D10LED, Red, TH, 4.0mm (or 5.0mm)10
6U18Low Dropout Linear Regulator, AZ1117-3.3, SOT-2231
7R1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R14, R15, R16Resistor, 330 Ohm, 5%, 1/4 W, 080516
8U1, U38-Bit Shift Register, 74HC595, SOIC-162
9CON1Female Header, 12-Pin (2x6), 2.54mm1

Pictures

The finished board:

Bare PCB (front and back):

License

This work is licensed under a Creative Commons Attribution 4.0 International License.

Contact

You can e-mail me at: email-address

Parts

47
QtyValueFootprintReferences
16330Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolderR1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R14, R15, R16
10LEDLED_THT:LED_D4.0mmD1, D2, D3, D4, D5, D6, D7, D8, D9, D10
51KResistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolderR17, R18, R19, R20, R21
5MMBT3904Package_TO_SOT_SMD:SOT-23Q4, Q5, Q6, Q7, Q8
274HC595Package_SO:SOIC-16_3.9x9.9mm_P1.27mmU1, U3
2NFD-4042AxDisplay_7Segment:NFD-4042AxLED1, LED2
122uFCapacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolderC1
1AZ1117-3.3Package_TO_SOT_SMD:SOT-223U18
1Conn_02x06_Odd_EvenConnector_PinSocket_2.54mm:PinSocket_2x06_P2.54mm_VerticalCON1

The 43 most common of 47 parts.

Similar boards

  • 4 layers140 × 100 mmDc usv, the printed circuit board in 3D

    Dc usv

    TobleMiner/DC-UPS

    A small DC UPS, designed to keep small appliances like consumer network equipment running during power outages

    351 parts223CERN-OHL-P-2.0
  • 2 layers171.5 × 106.7 mmSequencer, the printed circuit board in 3D

    Sequencer

    westlicht/performer-hardware

    PER|FORMER Eurorack Sequencer - Hardware Design Files

    435 parts110
  • 4 layers120 × 108 mmDk2 06, the printed circuit board in 3D

    Dk2 06

    mattybrad/drumkid2

    189 parts12GPL-3.0
  • 2 layers72.8 × 32 mmMicro fm radio, the printed circuit board in 3D

    Micro fm radio

    dilshan/rda5807-fm-radio-module

    RDA5807M based stereo FM radio receiver

    56 parts8MIT
  • 4 layers71.1 × 99.1 mmQuad adsr, the printed circuit board in 3D

    Quad adsr

    JordanAceto/quad_ADSR_board

    PCB for a quad eurorack ADSR

    197 parts5
  • 2 layers212.3 × 100 mmEuroSID, the printed circuit board in 3D

    EuroSID

    activexray/EuroSID

    A better SID Eurorack Module

    225 parts3
  • 2 layers148 × 90 mmClock v2, the printed circuit board in 3D

    Clock v2

    bonnetn/nixie_clock

    Nixie tube clock

    230 parts
  • 4 layers100 × 100 mmTouchSynth, the printed circuit board in 3D

    TouchSynth

    cpldcpu/TouchSynth

    Analog Monophonic Synthesizer with a touch keyboard. Controller by CH32V00x

    246 partsMIT

Questions

How big is the Ka3005p displaydriver PCB?

It measures 99.1 × 45.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Ka3005p displaydriver use?

47 parts, built around the 74HC595 and MMBT3904. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ka3005p displaydriver KiCad files?

From the djedditt/ka3005p-display repository on GitHub, at the commit this page was made from: the board is ka3005p_displaydriver.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ka3005p displaydriver design in my own project?

Its repository publishes it under the CC-BY-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).