

Sensor dev kit
STM8S005C6T6 IoT development board
- Size
- 87.9 × 55.4 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 90
- Nets
- 83
- Pads
- 348
- Tracks, vias
- 1,315, 114
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 14 Nov 2021
- Updated
- 15 Nov 2021
Overview
Sensor dev kit is an open-source printed circuit board by dilshan, from the dilshan/stm8s005-iot-devboard repository on GitHub, published under the GPL-2.0 licence. It is a 2-layer board of 87.9 × 55.4 mm with 90 parts on 83 nets, routed with 1,315 tracks and 114 vias.
It is built around the STM8S005C6T6, CH340G and AMS1117-3.3, with the USBLC6-2SC6, HR911105A and MMBT3904 among its other parts. Its parts include 23 capacitors, 20 resistors, 12 connectors, 6 diodes and 5 ICs. It belongs with the microcontroller boards and home automation and IoT boards and the STM8 boards of this library.
Main components
8STM8S005C6T6
LQFP-48(7x7)-40℃~+85℃ 10bit 128Byte 16MHz 2.95V~5.5V 2KB 32KB 38 8 Bit Built-in FLASH STM8 LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)CH340G
SOP-16-40℃~+85℃ 2Mbps 3.3V、5V USB 2.0 USB to UART SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)HR911105A
插件0℃~+70℃ 1 Filtered Gold Non-PoE Phosphor bronze RJ45 Jack Right Angle Shielded With LED 插件 Ethernet Connectors / Modular Connectors (RJ45 RJ11) ROHSHANRUNEthernet Connectors / Modular Connectors (RJ45 RJ11)MMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)SS24
SMA(DO-214AC)-55℃~+150℃ 200uA@40V 2A 40V 50A 550mV@2A Independent SMA(DO-214AC) Schottky Diodes ROHShongjiachengSchottky DiodesXM7D-0512
插件插件 USB Connectors ROHSOmronUSB Connectors
README
README.mdSTM8S005C6T6 Ethernet development board
This is an Ethernet development board based on STM8S005C6T6, designed specifically for IoT related applications. This development board consists of ENC28J60, 10BASE-T stand-alone Ethernet controller, CH340G, USB serial interface, 2 LED indicators, and passive buzzer unit.

The firmware framework for this development board has been developed using SDCC. To enable IPv4 support, we convert the EtherCard driver, which is available for the Arduino platform. The current version of this driver supports all other EtherCard functions except TCP support.
In the given design, the SPI terminals of the MCU are connected to the ENC28J60 Ethernet controller. All SPI terminals, such as MISO / PC7, MOSI / PC6, and SCK / PC5, are connected directly to the Ethernet controller. In addition, the PC4 terminal of the MCU is used as ENC28J60, CHIP-SELECT.
The CH340G USB serial interface is connected to the UART2 terminals of the MCU. In STM8S005C6T6, the UART2 is mapped to the PD6 and PD5 terminals of the MCU. The USB interface of this development board consists of the jack-sense feature. The jack-sense status can access from PD7.
The minor peripherals such as LED indicators and buzzer are connected to the PORTD of the MCU. The LED indicators are connected to terminals PD0 and PD1 and can be activated or deactivated via jumpers. The passive buzzer is connected to PD4 and can run through the STM8 beep sound generator unit.
All peripherals of this development board are powered by a 3.3V supply. The recommended supply voltage for this development board is 5V to 9V.
In addition to the STM8S005C6T6, this development board supports the following STM8 series, LQFP48 packaged microcontrollers: STM8S007C8T6, STM8S207C8T6, and STM8S105C6T6.
The schematic and PCB design of this project is released under the terms of CERN-OHL-W Version 2.0. The firmware framework is released under the terms of the GNU GPL 2.0 license.
Parts
90| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 0.1MFD | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C201, C404, C405, C501, C601, C602, C603, C604, C606, C609, C611 |
| 4 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R201, R302, R401, R402 |
| 4 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R303, R403, R404, R502 |
| 4 | 22pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C301, C302, C401, C402 |
| 4 | 50R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R406, R407, R408, R409 |
| 4 | M3 | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H101, H102, H103, H104 |
| 3 | 2.54mm Header | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP201, JP202, JP203 |
| 2 | 0.01MFD | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C303, C304 |
| 2 | 10MFD / 25V | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C607, C608 |
| 2 | 1M | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R501, R504 |
| 2 | 1N4148 | Diode_SMD:D_MiniMELF_Handsoldering | D301, D302 |
| 2 | 2.54mm Female Header | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J602, J603 |
| 2 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q501, Q502 |
| 2 | 560R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R503, R505 |
| 2 | THT-0ohm | Inductor_THT:L_Axial_L6.6mm_D2.7mm_P10.16mm_Horizontal_Vishay_IM-2 | FB602, FB603 |
| 1 | 0R | Inductor_THT:L_Axial_L6.6mm_D2.7mm_P10.16mm_Horizontal_Vishay_IM-2 | FB601 |
| 1 | 0R | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R601 |
| 1 | 100MFD / 25V | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C605 |
| 1 | 100mA | Fuse:Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F201 |
| 1 | 10MFD / 10V | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C403 |
| 1 | 10uH | Inductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | L401 |
| 1 | 12MHz | Crystal:Crystal_HC49-U_Vertical | Y301 |
| 1 | 1MFD / 10V | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C610 |
| 1 | 1MFD / 10V | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C202 |
| 1 | 2.2K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R506 |
| 1 | 2.54mm Female Header | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J203 |
| 1 | 2.54mm Female Header | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J204 |
| 1 | 2.54mm Female Header | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J206 |
| 1 | 2.54mm Female Header | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J205 |
| 1 | 2.54mm Female Header | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | J202 |
| 1 | 2.54mm Female Header | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J201 |
| 1 | 2.54mm Male Header | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J207 |
| 1 | 2.7K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R405 |
| 1 | 25MHz | Crystal:Crystal_HC49-U_Vertical | Y401 |
| 1 | 3.5mm Screw Terminal | Connector_Phoenix_MC:PhoenixContact_MCV_1,5_2-G-3.5_1x02_P3.50mm_Vertical | J601 |
| 1 | 500mA | Fuse:Fuse_2816_7142Metric_Pad3.20x4.45mm_HandSolder | F601 |
| 1 | 6.8K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R301 |
| 1 | 6x6 TACT | Button_Switch_THT:SW_PUSH_6mm | SW201 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U601 |
| 1 | CH340G | Package_SO:SOP-16_3.9x9.9mm_P1.27mm | U301 |
| 1 | ENC28J60x-SS | Package_SO:SSOP-28_5.3x10.2mm_P0.65mm | U401 |
| 1 | FREQ-TP | TestPoint:TestPoint_Pad_D1.0mm | TP201 |
| 1 | HR911105A | sensor-dev-kit:HR911105A | J401 |
| 1 | LED-GREEN-0805 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D501 |
| 1 | LED-RED-0805 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D502 |
| 1 | LED-YELLOW-0805 | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D503 |
| 1 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q503 |
| 1 | Passive-Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ501 |
| 1 | SJ-CLOSE | Jumper:SolderJumper-2_P1.3mm_Bridged2Bar_RoundedPad1.0x1.5mm | JP401 |
| 1 | SJ-OPEN | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP402 |
| 1 | SS24 | Diode_SMD:D_SMB_Handsoldering | D601 |
| 1 | STM8S005C6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U201 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U302 |
| 1 | XM7D-0512 | sensor-dev-kit:OMRON_XM7D-0512 | J301 |
The 89 most common of 90 parts.
Similar boards
- 2 layers30 × 20.3 mm

- 2 layers82.1 × 22.5 mm

Star pointer
dilshan/star-pointer
DIY virtual electronic finderscope for astronomical telescopes
39 parts24MIT - 2 layers70 × 70 mm

Fwrtss
ynsta/fwrtss
Open source hardware and software project of a regulated soldering station for RT soldering tips
103 parts7 - 2 layers116.8 × 102.9 mm

- 2 layers68.5 × 53.3 mm

Iot wifi uno hw
iotmakervn/iot-wifi-uno-hw
Open hardware ESP8266 Uno board - Internet Of Things WiFi Uno
56 parts26 - 4 layers72.6 × 170 mm

OpenJBOD RP2040
OpenJBOD/rp2040
This repository contains the hardware design files OpenJBOD RP2040 Baseboard.
129 parts87CERN-OHL-P-2.0 - 4 layers75 × 40 mm

- 4 layers80 × 100 mm

Baseboard
NVIDIA-AI-IOT/my-jetson-nano-baseboard
An open source Jetson Nano baseboard and tools to design your own.
240 parts91
Questions
How big is the Sensor dev kit PCB?
It measures 87.9 × 55.4 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Sensor dev kit use?
90 parts, built around the STM8S005C6T6, CH340G, AMS1117-3.3 and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Sensor dev kit KiCad files?
From the dilshan/stm8s005-iot-devboard repository on GitHub, at the commit this page was made from: the board is design/sensor-dev-kit.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Sensor dev kit design in my own project?
Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).