
FlySensei Stack Actuation ECAD
denjos007/FlySensei_Stack_ECAD
PCB Design for the Stacked design for Blimp Controller

PCB Design for the Stacked design for Blimp Controller
FlySensei Stack Sensing ECAD is an open-source printed circuit board by denjos007, from the denjos007/FlySensei_Stack_ECAD repository on GitHub. It is a 4-layer board of 90 × 65 mm with 49 parts on 113 nets, routed with 536 tracks and 229 vias.
It is built around the VL53L0CXV0DH/1, TS5A3159ADCKR and BNO055. Its parts include 13 capacitors, 12 resistors, 6 ICs, 4 connectors and 2 switches.
Stackable base board for the Raspberry Pi CM4 with an integrated AI co-processor
Joseph Prince Mathew - jprincem@masonlive.gmu.edu
| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 0u1F | Capacitor_SMD:C_0402_1005Metric | C1, C4, C5, C6, C7, C8, C9, C10, C11 |
| 6 | 10K | Resistor_SMD:R_0402_1005Metric | R2, R3, R4, R6, R7, R8 |
| 6 | JST_SH_SM04 | Connector_JST:JST_SH_SM04B-SRSS-TB_1x04-1MP_P1.00mm_Horizontal | LR1, LR2, LR3, LR4, LR5, LR6 |
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5_Pad_Via | H1, H2, H3, H4 |
| 2 | 0K | Resistor_SMD:R_0402_1005Metric | R1, R5 |
| 2 | 22pF | Capacitor_SMD:C_0402_1005Metric | C2, C3 |
| 2 | Conn_02x20_Odd_Even_Female | Connector_PinHeader_1.27mm:PinHeader_2x20_P1.27mm_Vertical_SMD | J2, J4 |
| 2 | Conn_02x20_Odd_Even_Male | Connector_PinHeader_1.27mm:PinHeader_2x20_P1.27mm_Vertical_SMD | J1, J3 |
| 2 | SW_SPDT | Button_Switch_SMD:SW_SPDT_PCM12 | SW1, SW2 |
| 2 | TS5A3159ADCKR | Package_TO_SOT_SMD:SOT-363_SC-70-6 | U9, U10 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C12 |
| 1 | 22uF | Capacitor_SMD:C_0603_1608Metric | C13 |
| 1 | 24K | Resistor_SMD:R_0402_1005Metric | R12 |
| 1 | 55K | Resistor_SMD:R_0402_1005Metric | R9 |
| 1 | 62K | Resistor_SMD:R_0402_1005Metric | R10 |
| 1 | 75K | Resistor_SMD:R_0402_1005Metric | R11 |
| 1 | BNO055 | Package_LGA:LGA-28_5.2x3.8mm_P0.5mm | U1 |
| 1 | Crystal | Crystal:Crystal_SMD_2012-2Pin_2.0x1.2mm_HandSoldering | Y1 |
| 1 | D_SCHTKY | Diode_SMD:D_SMB | D1 |
| 1 | MPM3610 | Package_DFN_QFN_U:MPM3610_QFN-20_5x3mm | U4 |
| 1 | TCA9548APWR | Package_SO:TSSOP-24_4.4x7.8mm_P0.65mm | U2 |
| 1 | VL53L0CXV0DH_1 | Sensor_Distance:ST_VL53L1x | U3 |

denjos007/FlySensei_Stack_ECAD
PCB Design for the Stacked design for Blimp Controller

denjos007/FlySensei_Stack_ECAD
PCB Design for the Stacked design for Blimp Controller

denjos007/FlySensei_Stack_ECAD
PCB Design for the Stacked design for Blimp Controller

sabogalc/KiCad-Arduino-Boards
A collection of Arduino boards recreated from scratch in KiCad. Legacy USB connectors have been replaced with USB-C where applicable.



GroundStudio/GroundStudio-VL53L0CX-module
GroundStudio Time of Flight Distance Sensor module ====================================




It measures 90 × 65 mm and has 4 copper layers, 1.18 mm thick.
49 parts, built around the VL53L0CXV0DH/1, TS5A3159ADCKR and BNO055. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the denjos007/FlySensei_Stack_ECAD repository on GitHub, at the commit this page was made from: the board is FlySensei_Stack_Sensing_ECAD/FlySensei_Stack_Sensing_ECAD.kicad_pcb and its schematic FlySensei_Stack_Actuation_ECAD/FlySensei_Stack_Actuation_ECAD.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask denjos007 before reusing the design.