

ESP32Sensor LED board
Horticulture Fluorescence Sensor Project
- Size
- 41.4 × 53.5 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 48
- Nets
- 48
- Pads
- 226
- Tracks, vias
- 366, 35
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 27 May 2022
- Updated
- 18 Nov 2024
Overview
ESP32Sensor LED board is an open-source printed circuit board by LESA-RPI, from the LESA-RPI/hfs.main repository on GitHub. It is a 4-layer board of 41.4 × 53.5 mm with 48 parts on 48 nets, routed with 366 tracks and 35 vias.
It is built around the TL4242TDRJRQ1, VL53L0CXV0DH/1 and XPEBRY-L1-R250-00P01, with the CRM1206-JW-1R0ELF, 354010RFT and CLP-103-02-F-D-BE among its other parts. Its parts include 17 resistors, 12 diodes, 10 capacitors, 5 ICs and 2 connectors. It belongs with the ESP32 boards of this library.
Main components
7TL4242TDRJRQ1
SON-8-EP(4x4)-40℃~+105℃ 1 4.5V~42V 5% 500mA PWM Short Circuit Protection、Over-Temperature Protection (OTP)、LED open-circuit protection SON-8-EP(4x4) LED Drivers ROHSTexas InstrumentsLED DriversVL53L0CXV0DH/1
SMD-12P,4.4x2.4mm-20℃~+70℃ 19mA 1mm 2.4mm 2.6V~3.5V 200cm 4.4mm I2C Self-calibration Yes SMD-12P,4.4x2.4mm Position Sensors ROHSSTMicroelectronicsPosition SensorsXPEBRY-L1-R250-00P01
SMDLED Indication - DiscreteCree LEDCRM1206-JW-1R0ELF
12061Ω 500mW Current Sense Resistor ±200ppm/℃ ±5% 1206 Current Sense Resistors / Shunt Resistors ROHSBournsCurrent Sense Resistors / Shunt Resistors354010RFT
2816-55℃~+155℃ 10Ω 250V 4W Thick Film Resistor ±1% ±200ppm/℃ 2816 Chip Resistor - Surface MountTE ConnectivityChip Resistor - Surface MountCLP-103-02-F-D-BE
SMD,P=1.27mm-55℃~+125℃ 1.27mm 1.27mm 2 2.14mm 3.3A 6P Square Hole Surface Mount,Vertical Tin Top SMD,P=1.27mm Female Headers ROHSSamtecFemale HeadersIRLHS6376TRPBF
PQFN-6(2x2)-55℃~+150℃ 1.1V 1.5W 2 N-Channel 2.8nC@15V 20pF 270pF 3.4A 30V 63mΩ@4.5V PQFN-6(2x2) MOSFETs ROHSInfineon TechnologiesMOSFETs
README
README.mdHorticulture Fluorescence Sensor Project
The Horticulture Fluorescence Sensor (HFS) is a remote chlorophyll-A flourescence sensor. If you are doing any editing of this project, please do it on a branch and merge down after approval. Do not edit directly onto the main branch.
Sensors
This project relies on a controller inside of the sensor casing to run device code. These devices are not connected to wi-fi, instead using BLE communication. For information on how to setup and run the sensor code on a microcontroller, click here.
Data Server and Localhost
Data collected by the sensors is sent to a local data server over BLE. The server connects to wi-fi so that data can be sent to the cloud or accessed via a local webserver. For more information on how to setup and run the server code, click here.
Simulation
A flourescence simulation was created in order to speed up prototype development.
Parts
48| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | XPEBRY-L1-R250-00P01 | Library:HFS_LED | LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8, LED9, LED10, LED11, LED12 |
| 8 | CRM1206-JW-1R0ELF | footprints:BO_CR1206 | R1, R2, R4, R5, R7, R8, R10, R11 |
| 4 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C2, C4, C6, C7 |
| 4 | 1 | Resistor_SMD:R_0402_1005Metric | R14, R15, R16, R17 |
| 4 | 354010RFT | footprints:RES_3540_TEC | R3, R6, R9, R12 |
| 4 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C1, C3, C5, C8 |
| 4 | TL4242TDRJRQ1 | footprints:DRJ8_3X2P2 | U1, U2, U3, U4 |
| 2 | CLP-103-02-F-D-BE | footprints:CONN_CLP-103-02-X-D-BE_SAI | J1, J2 |
| 2 | IRLHS6376TRPBF | footprints:PQFN6_IRLHS6376TRPBF_INF | K1, K2 |
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric | C9 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric | R13 |
| 1 | 4700nF | Capacitor_SMD:C_0402_1005Metric | C10 |
| 1 | VL53L0CXV0DH/1 | footprints:LGA12_STM | U5 |
More from LESA-RPI/hfs.main
3- 4 layers

- 4 layers38 × 60 mm

- 4 layers38 × 60 mm

Similar boards
- 2 layers57.6 × 40 mm

- 2 layers87 × 76 mm

- 2 layers21 × 18 mm

REV0.1 HIVAWN GS GS VL53L0CX
GroundStudio/GroundStudio-VL53L0CX-module
GroundStudio Time of Flight Distance Sensor module ====================================
23 parts - 2 layers30 × 30 mm

- 4 layers52 × 42 mm

- 4 layers90 × 65 mm

FlySensei Stack Sensing ECAD
denjos007/FlySensei_Stack_ECAD
PCB Design for the Stacked design for Blimp Controller
49 parts - 2 layers200 × 22 mm

- 2 layers15.2 × 24.6 mm

Questions
How big is the ESP32Sensor LED board PCB?
It measures 41.4 × 53.5 mm and has 4 copper layers, 1.6 mm thick.
What parts does the ESP32Sensor LED board use?
48 parts, built around the TL4242TDRJRQ1, VL53L0CXV0DH/1, XPEBRY-L1-R250-00P01 and CRM1206-JW-1R0ELF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32Sensor LED board KiCad files?
From the LESA-RPI/hfs.main repository on GitHub, at the commit this page was made from: the board is sensor/client-design/KiCad/ESP32Sensor-LED_board/ESP32Sensor-LED_board.kicad_pcb and its schematic sensor/client-design/KiCad/ESP32Sensor-Archive/ESP32Sensor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32Sensor LED board design in my own project?
Its repository states no licence, so its author keeps all rights: ask LESA-RPI before reusing the design.