
PSLab
fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

Electronics Circuits ...
Faden is an open-source printed circuit board by ct2034, from the ct2034/ctronics repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board with 35 parts on 22 nets, routed with 152 tracks and 46 vias.
It is built around the TL082. Its parts include 13 resistors, 11 capacitors, 4 diodes, 2 connectors and 1 IC.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R11, R12 |
| 3 | R_POT | Potentiometer_THT:Potentiometer_Vishay_T73XW_Horizontal | RV1, RV2, RV4 |
| 2 | 10n | Capacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mm | C7, C10 |
| 2 | 1Meg | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3, R9 |
| 2 | 1u | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C11, C12 |
| 2 | 220n | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C4, C6 |
| 2 | D | Diode_THT:D_DO-34_SOD68_P7.62mm_Horizontal | D1, D2 |
| 1 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
| 1 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R6 |
| 1 | 10n | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C2 |
| 1 | 10u | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C5 |
| 1 | 1Meg | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R5 |
| 1 | 1n | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mm | C1 |
| 1 | 22n | Capacitor_THT:C_Disc_D4.3mm_W1.9mm_P5.00mm | C8 |
| 1 | 47k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R7 |
| 1 | 47n | Capacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mm | C3 |
| 1 | 4k7 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R8 |
| 1 | 50k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R10 |
| 1 | 560 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
| 1 | Conn_01x02_Male | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1Power1 |
| 1 | Conn_01x04_Male | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2Signal1 |
| 1 | DIODE | Diode_THT:D_DO-15_P10.16mm_Horizontal | D8 |
| 1 | LED_Dual_CAC | LED_THT:LED_D3.0mm-3 | D3 |
| 1 | SW_DPDT_x2 | Button_Switch_THT:SW_E-Switch_EG1271_DPDT | SW1 |
| 1 | TL082 | Package_DIP:DIP-8_W7.62mm_Socket | U1 |

fossasia/pslab-hardware
PSLab Hardware Design and Schematics https://pslab.io

QuantumVillage/UncutGem
A prototype Full Stack fully Open Source NV Center Diamond Magnetometer

profdc9/DRSSTC-PCB-Pack
A pack of PCBs for a dual resonant solid state tesla coil setup. Pretty much everything you need.


tvlad1234/osillyscope
Low cost, low part count CH32V003-based oscilloscope


grappendorf/eurorack-spinfx
Spin FV-1 based effects module for Eurorack systems

telec16/modular-synth
Little side project, don't expect much updates.
35 parts, built around the TL082. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ct2034/ctronics repository on GitHub, at the commit this page was made from: the board is faden/kicad/faden/faden.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).