

Scopetester
An Open Hardware project for a small Oscilloscope tester with features like the Hameg HZ-60
- Size
- 95 × 55 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 55
- Nets
- 50
- Pads
- 163
- Tracks, vias
- 237, 20
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 5 Nov 2017
- Updated
- 12 Aug 2026
Overview
Scopetester is an open-source printed circuit board by cosenmarco, from the cosenmarco/scopetester repository on GitHub. It is a 2-layer board of 95 × 55 mm with 55 parts on 50 nets, routed with 237 tracks and 20 vias.
It is built around the PIC16F1823-I/ST, 74AC14SC and BSS138, with the IRLML6401 among its other parts. Its parts include 22 resistors, 12 capacitors, 4 connectors, 3 ICs and 3 switches. It belongs with the PIC boards of this library.
Main components
4PIC16F1823-I/ST
TSSOP-14-40℃~+85℃ 1.8V~5.5V 10bit 12 128Byte 256Byte 3.5KB 32MHz 8 Bit Built-in FLASH PIC TSSOP-14 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)74AC14SC
SOIC-14-40℃~+85℃ 10ns@5V,50pF 2.2V~3.9V 24mA 24mA 2V~6V 2uA 4.76V~5.4V 440mV 500mV~1.1V 6 6 74AC Schmitt trigger SOIC-14 Inverters ROHSonsemiInvertersBSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETsIRLML6401
SOT-23-55℃~+150℃ 1 P-Channel 1.3W 125pF 12V 15nC@5V 180pF 4.3A 830pF 85mΩ@1.8V 950mV P-Channel SOT-23 MOSFETs ROHSKEXINMOSFETs
README
README.mdScopeTester
An Open Hardware project for a small oscilloscope tester and calibrator with features like the Hameg HZ-60.
License
This project aims to be "open" in the sense of Open Hardware and Free Libre Open Source. The project is made available under the terms of the Creative Commons license.
Tools
The harware is developed using KiCAD. Firmware is developed using MPLAB X and the XC8 compiler from Microchip.
Parts
55| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100R | Resistors_SMD:R_0603_HandSoldering | R17, R20, R21, R22 |
| 4 | Jumper | Pin_Headers:Pin_Header_Straight_2x01_Pitch2.54mm | ICSPCLK, ICSPDAT, VDD, VPP |
| 3 | 0 | Capacitors_SMD:C_0603_HandSoldering | C6, C9, C11 |
| 2 | 0.01µF | Capacitors_SMD:C_0603_HandSoldering | C10, C12 |
| 2 | 150R | Resistors_SMD:R_0603_HandSoldering | R11, R18 |
| 2 | 15R | Resistors_SMD:R_0603_HandSoldering | R9, R10 |
| 2 | 1K5 | Resistors_SMD:R_0603_HandSoldering | R14, R19 |
| 2 | 22pF | Capacitors_THT:C_Disc_D3.0mm_W1.6mm_P2.50mm | C2, C3 |
| 2 | 56K | Resistors_SMD:R_0603_HandSoldering | R5, R6 |
| 1 | 0.22µF | Capacitors_SMD:C_0603_HandSoldering | C4 |
| 1 | 0R | Resistors_SMD:R_0603_HandSoldering | R3 |
| 1 | 100K | Resistors_SMD:R_0603_HandSoldering | R16 |
| 1 | 100nF | Capacitors_SMD:C_0603_HandSoldering | C5 |
| 1 | 10K | Resistors_SMD:R_0603_HandSoldering | R2 |
| 1 | 10µF | Capacitors_THT:CP_Radial_D4.0mm_P1.50mm | C8 |
| 1 | 12k | Resistors_SMD:R_0603_HandSoldering | R8 |
| 1 | 2.5Vpp | Conns:bnc-ci-large | J2 |
| 1 | 220K | Potentiometers:Potentiometer_Trimmer_Piher_PT-6v_Horizontal | R15 |
| 1 | 226R | Resistors_SMD:R_0603_HandSoldering | R12 |
| 1 | 250mV | Conns:bnc-ci-large | J3 |
| 1 | 25mVpp into 50 Ohm | Conns:bnc-ci-large | J4 |
| 1 | 3.3µF | Capacitors_THT:CP_Radial_D4.0mm_P1.50mm | C7 |
| 1 | 301R | Resistors_SMD:R_0603_HandSoldering | R13 |
| 1 | 330nF | Capacitors_SMD:C_0603_HandSoldering | C1 |
| 1 | 33k | Resistors_SMD:R_0603_HandSoldering | R7 |
| 1 | 4xLR6(AA) | Wire_Pads:SolderWirePad_single_0-8mmDrill | BATT+ |
| 1 | 560R | Resistors_SMD:R_0603_HandSoldering | R1 |
| 1 | 5K6 | Resistors_SMD:R_0603_HandSoldering | R4 |
| 1 | 5VDC | Connectors:BARREL_JACK | J1 |
| 1 | 74AC14 | SMD_Packages:SOIC-14_N | U2 |
| 1 | 8.000Mhz | Crystals:Crystal_HC49-4H_Vertical | Y1 |
| 1 | BATTERY/DC | Buttons_Switches:SW_DPDT_Slide_mini | SW1 |
| 1 | BSS138 | TO_SOT_Packages_SMD:SOT-23 | Q1 |
| 1 | FREQ SEL | Buttons_Switches_THT:SW_DIP_x3_W7.62mm_Slide_LowProfile | SW3 |
| 1 | GND | Pin_Headers:Pin_Header_Straight_1x01_Pitch2.54mm | GND |
| 1 | IRLML6401 | TO_SOT_Packages_SMD:SOT-23 | Q2 |
| 1 | ON/ERROR | LEDs:LED_D5.0mm-3 | D1 |
| 1 | ON/OFF | Buttons_Switches:DPDT_Button_mini | SW2 |
| 1 | PIC16F1823-I/ST | SMD_Packages:SOIC-14_N | U1 |
| 1 | TEST | Wire_Pads:SolderWirePad_single_0-8mmDrill | BATT- |
| 1 | TS2951 | SMD_Packages:SOIC-8-N | U3 |
Similar boards
- 4 layers41.4 × 108 mm

- 2 layers39.6 × 18 mm

SnowBackpack
wandering-nora/SnowBackpack
A little driver for SnowPixel displays
110 parts1CERN-OHL-S-2.0 - 4 layers48.5 × 25 mm

- 6 layers100 × 100 mm

Imx8x carrier v2
BroncoSpace-Lab/scales-hardware
Hardware design files for the Spacecraft Compartmentalized Autonomous Learning and Edge Computing System (SCALES)
242 parts6 - 6 layers285 × 236 mm

Ra9704
Coin-OpCollection/Development-Documentation
This repository contains technical information, documentation, and reverse-engineering details for the base platform systems of FPGA implementations released by Coin-Op Collection.
228 parts11 - 4 layers68.6 × 58.4 mm

- 2 layers124.5 × 64.8 mm

Pa3gyf gpsdocxo-2016-pll r2
jandejongh/pa3gyf-gpsdocxo
GPS-Disciplined OCXO (In Progress)
298 parts2Apache-2.0 - 4 layers45 × 45 mm

Questions
How big is the Scopetester PCB?
It measures 95 × 55 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Scopetester use?
55 parts, built around the PIC16F1823-I/ST, 74AC14SC, BSS138 and IRLML6401. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Scopetester KiCad files?
From the cosenmarco/scopetester repository on GitHub, at the commit this page was made from: the board is ScopeTester.KiCAD/ScopeTester.kicad_pcb and its schematic ScopeTester.KiCAD/ScopeTester.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Scopetester design in my own project?
Its repository states no licence, so its author keeps all rights: ask cosenmarco before reusing the design.
