

ATtiny
Hacemos roboces tope tochos
- Size
- 60 × 82 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 33
- Nets
- 37
- Pads
- 129
- Tracks, vias
- 357, 0
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 3 Dec 2018
- Updated
- 20 Jul 2023
Overview
ATtiny is an open-source printed circuit board by Complubot, from the Complubot/AZ5 repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 60 × 82 mm with 33 parts on 37 nets, routed with 357 tracks and 0 vias.
It is built around the ATTINY1634-SU, L7805 and US2D. Its parts include 13 connectors, 6 resistors, 5 diodes, 4 capacitors and 2 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3ATTINY1634-SU
SOIC-20-300mil-40℃~+85℃ 1.8V~5.5V 10bit 12MHz 16KB 18 1KB 256Byte 8 Bit AVR Built-in FLASH SOIC-20-300mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontroller Units (MCUs/MPUs/SOCs)L7805
TO-220ST0℃~+125℃@(Tj) 1 1.2A 20V 2V@(1A) 42uV 500uA 5V 73dB@(120Hz) Fixed Positive Short Circuit Protection TO-220ST Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSOSENVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUS2D
SMA-55℃~+150℃ 1 Independent 1V@2A 200V 2A 50A 50ns 5uA@200V SMA Fast Recovery / High Efficiency Diodes ROHSMDDFast Recovery / High Efficiency Diodes
README
README.mdAZ5 Robot
Parts
33| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | Agujero | huellas:hole | J8, J9, J10, J11 |
| 2 | C22pF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C3, C4 |
| 2 | Conn_01x02 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J6, J7 |
| 2 | D_Zener | Diode_SMD:D_SOD-323_HandSoldering | D3, D4 |
| 2 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 2 | R10K | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R3, R4 |
| 2 | R330 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R1, R2 |
| 2 | R68 | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R5, R6 |
| 1 | ATtiny1634-SU | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U1 |
| 1 | C100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C1 |
| 1 | CP47uF | Capacitor_SMD:CP_Elec_6.3x5.3 | C2 |
| 1 | Conn_01x02_XT30 | proyectoAjeno:XT30PW-F | J12 |
| 1 | Conn_01x03_Alimentacion | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | J13 |
| 1 | Conn_01x04_Serie_0 | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J4 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | Conn_01x06_Serie_1_ICSP | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J5 |
| 1 | Conn_01x09 | Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_Vertical | J14 |
| 1 | Crystal 16MHz | Compluino_03:Crystal | Y1 |
| 1 | L7805 | huellas:7805 | U2 |
| 1 | Polyfuse | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Vertical | F1 |
| 1 | SW_Push | huellas:Pulsador_5,2x5,2 | SW1 |
| 1 | US2D | Diode_SMD:D_SMB_Handsoldering | D5 |
| 1 | USB_B_Micro | other:MICRO_USB_SMD | J2 |
More from Complubot/AZ5
4- 2 layers80 × 132 mm

- 2 layers

- 2 layers47 × 75.6 mm

- 2 layers21.4 × 26.4 mm

Similar boards
- 2 layers66 × 58.4 mm

- 2 layers65 × 56.5 mm

RPi Hat
Blake-Robotics/PiUPS
Project to manage the power supply for the electronics of the robot. A microcontroller is used to monitor the state of the battery and external power inputs.
86 partsGPL-2.0 - 2 layers66.4 × 90.9 mm

- 2 layers55 × 40 mm

LevelHacker
HackRVA/LevelHacker
An introductory electronic device designed in KiCad, for use with the electronics workshop
26 parts - 2 layers85.7 × 157.5 mm

- 4 layers75 × 100 mm

- 2 layers106.7 × 83.8 mm

Controller
Miceuz/triac-bloc
An universal power block based on triac. In essence this is a solid state relay with some bells and whistles
23 parts54 - 2 layers27.4 × 1.3 mm

Thermocouple attiny1634
Miceuz/thermocouple-modbus
Thermocouple frontend accessible via industrial modbus protocol
40 parts2
Questions
How big is the ATtiny PCB?
It measures 60 × 82 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ATtiny use?
33 parts, built around the ATTINY1634-SU, L7805 and US2D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ATtiny KiCad files?
From the Complubot/AZ5 repository on GitHub, at the commit this page was made from: the board is ELECTRONICA/ATtiny_1.0/ATtiny.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ATtiny design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).