2 layers100 × 105 mm
ESP Pixel LED Controller
lukas-riffel/ESP-Pixel-LED-Controller
An open source Pixel-LED-Decoder based on WT32-ETH01 using WLED with usermods.
37 parts3MIT
2 layers66.4 × 90.9 mm
DMX2SGM
Gabse/DMX2SGMDMX512 to SGM256 Converter
- Size
- 66.4 × 90.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 32
- Nets
- 37
- Pads
- 133
- Tracks, vias
- 179, 8
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 18 Apr 2020
- Updated
- 24 Jul 2022
Overview
DMX2SGM is an open-source printed circuit board by Gabse, from the Gabse/DMX2SGM repository on GitHub. It is a 2-layer board of 66.4 × 90.9 mm with 32 parts on 37 nets, routed with 179 tracks and 8 vias.
It is built around the ATTINY1634-SU, REE-0505S and 74HC14, with the BD09AV among its other parts. Its parts include 9 capacitors, 6 ICs, 5 resistors, 5 connectors and 3 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
4
ATTINY1634-SU
SOIC-20-300mil-40℃~+85℃ 1.8V~5.5V 10bit 12MHz 16KB 18 1KB 256Byte 8 Bit AVR Built-in FLASH SOIC-20-300mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontroller Units (MCUs/MPUs/SOCs)REE-0505S
SIP,19.7x6mm1 1W 1kV 200mA 4.5V~5.5V 5V 76% SIP,19.7x6mm Isolated Power Modules ROHSRECOM PowerIsolated Power Modules
74HC14
SOP-14-40℃~+85℃ 1.9V、3.98V、4.4V、5.48V、5.9V 100mV、260mV、260mV 20uA 25ns@4.5V,50pF 2V~6V 6 74HC Noise suppression function Schmitt trigger SOP-14 Inverters ROHSJSMSEMIInverters
BD09AV
插件,P=2.54mm-40℃~+85℃ 100mA 2.54mm 5V 9 PC Pin Red SPST Slide, Rocked 插件,P=2.54mm DIP Switches ROHSC&KDIP Switches
README
README.mdDMX2SGM
DMX512 to Dual SGM256 Converter
This simple device converts a standard DMX512 Signal into two SGM256 signals.
It lets you reuse your old SGM gear with almost any standard DMX controller on the market.
The device has 2 independent outputs for DMX channel 1 to 256 and 257 to 512 and can be powered by ether one of them.
Due to its small form factor it can be installed nearly anywhere in the SGM signal path replacing old SGM Regia lighting desks directly.
9 Dip Swithes let you set a DMX start address, making it easy to expand existing DMX universes.
The opto-isolated input helps you avoiding ground loops between the DMX and the SGM side.
Please also visit my Blog Post for additional information.
Safety information / disclaimer:
This device SHOULD NOT be used with anything safety related. It is only meant to control dimmer packs and other lighting fixtures. It is not allowed to be used with moving stage parts, pyros and similar SFX. Doing so will happen at your OWN RISK!
Parts
32| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100n | Capacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mm | C1, C3, C6, C9 |
| 4 | 390R | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R2, R3, R4, R5 |
| 4 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J2, J3, J4, J5 |
| 2 | 1N4007 | Diode_THT:D_DO-15_P12.70mm_Horizontal | D2, D3 |
| 2 | 22p | Capacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mm | C2, C4 |
| 2 | B59990C0120A07 | Varistor:RV_Disc_D7mm_W3.4mm_P5mm | TH1, TH2 |
| 1 | 100n | Capacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mm | C7 |
| 1 | 10µ | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C5 |
| 1 | 12MHz | Crystal:Crystal_HC49-4H_Vertical | Y1 |
| 1 | 1µ | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C8 |
| 1 | 2K2 | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R1 |
| 1 | 485 | Package_DIP:DIP-8_W7.62mm_Socket_LongPads | U2 |
| 1 | 6N137 | Package_DIP:DIP-8_W7.62mm_Socket_LongPads | U3 |
| 1 | 74HC14 | Package_DIP:DIP-14_W7.62mm_Socket_LongPads | U5 |
| 1 | 7805 | Package_TO_SOT_THT:TO-220-3_Vertical | U6 |
| 1 | ATtiny1634 | Housings_SOIC:SOIC-20W_7.5x12.8mm_Pitch1.27mm | U1 |
| 1 | AVR-ISP-6 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J1 |
| 1 | BD09AV | manuf:BD09AV | SW1 |
| 1 | LED | LED_THT:LED_D5.0mm | D1 |
| 1 | REE-0505S | manuf:RECOM-REE-0505S | U4 |
Similar boards
- 2 layers73.7 × 90.2 mm
- 4 layers76.2 × 71.1 mm
Fobosshield
GMUCERG/fobos
Flexible Open-source workBench fOr Side-channel analysis (FOBOS)
170 parts18Apache-2.0 - 2 layers80 × 132 mm
- 2 layers66 × 58.4 mm
- 2 layers65 × 56.5 mm
RPi Hat
Blake-Robotics/PiUPS
Project to manage the power supply for the electronics of the robot. A microcontroller is used to monitor the state of the battery and external power inputs.
86 partsGPL-2.0 - 2 layers55 × 40 mm
LevelHacker
HackRVA/LevelHacker
An introductory electronic device designed in KiCad, for use with the electronics workshop
26 parts - 2 layers85.7 × 157.5 mm
Questions
How big is the DMX2SGM PCB?
It measures 66.4 × 90.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the DMX2SGM use?
32 parts, built around the ATTINY1634-SU, REE-0505S, 74HC14 and BD09AV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DMX2SGM KiCad files?
From the Gabse/DMX2SGM repository on GitHub, at the commit this page was made from: the board is Layout/DMX2SGM.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the DMX2SGM design in my own project?
Its repository states no licence, so its author keeps all rights: ask Gabse before reusing the design.