2 layers45.7 × 38 mm
SmartLED Shield Breakout
coelacant1/Protogen-Electronics
SmartMatrix SmartLED Shield breakout for Protogen hardware
24 parts8GPL-3.0
4 layers65 × 52 mm
ProtogenControllerV1
coelacant1/Protogen-Electronics8SmartMatrix SmartLED Shield breakout for Protogen hardware
- Size
- 65 × 52 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 77
- Nets
- 86
- Pads
- 338
- Tracks, vias
- 989, 149
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 21 May 2024
- Updated
- 9 Mar 2026
Overview
ProtogenControllerV1 is an open-source printed circuit board by coelacant1, from the coelacant1/Protogen-Electronics repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 65 × 52 mm with 77 parts on 86 nets, routed with 989 tracks and 149 vias.
It is built around the SN74HCT245DWR(LX), CP2104-F03-GM and AP2112K-3.3TRG1, with the CC0805KKX7R6BB105, CRCW08050000Z0EA and B3B-XH-A(LF)(SN) among its other parts. Its parts include 18 resistors, 16 capacitors, 12 connectors, 5 ICs and 4 transistors. It belongs with the ESP32 boards of this library.
Main components
11
SN74HCT245DWR(LX)
SOP-20SOP-20 Buffers, Drivers, Receivers, Transceivers ROHSlingxingicBuffers, Drivers, Receivers, Transceivers
CP2104-F03-GM
QFN-24-EP(4x4)-40℃~+85℃ 1.8V、3V~3.6V 100uA 17mA 2Mbps USB 2.0 USB to UART QFN-24-EP(4x4) USB Converters ROHSSilicon LabsUSB Converters
AP2112K-3.3TRG1
SOT-25-5-40℃~+85℃@(Ta) 1 250mV@(600mA) 3.3V 50uVrms 55uA 600mA 65dB@(1kHz) 6V Fixed Over Current Protection、Thermal Shutdown、Enable control Positive SOT-25-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
CC0805KKX7R6BB105
080510V 1uF X7R ±10% 0805 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSYAGEOMultilayer Ceramic Capacitors MLCC - SMD/SMT
CRCW08050000Z0EA
0805-55℃~+155℃ 0Ω 125mW 200V Thick Film Resistor 0805 Chip Resistor - Surface Mount ROHSVishay IntertechnologyChip Resistor - Surface Mount
B3B-XH-A(LF)(SN)
插件,P=2.5mm-25℃~+85℃ 1 1x3P 2.5mm 250V 3 3A 3P 5.75mm 7mm 9.9mm Brass K Pin PA66 Through Hole Tin UL94V-0 White XH 插件,P=2.5mm Wire To Board Connector ROHSJSTWire To Board Connector
150080SS75000
0805-40℃~+85℃ 1.9V 140° 20mA 60mcd 630nm 645nm Discrete Diode Water Clear 0805 LED Indication - Discrete ROHSWürth ElektronikLED Indication - Discrete
CAT16-103J4LF
0603x410kΩ 4 62.5mW 8 ±200ppm/℃ ±5% 0603x4 Resistor Networks, Arrays ROHSBournsResistor Networks & Arrays
MMBT2222ALT1G-CN
SOT-23SOT-23 Bipolar (BJT) ROHSChipNoboBipolar (BJT)FDN339AN
SOT-23-55℃~+150℃ 1 N-channel 120pF 1V 1W 20V 25mΩ@4.5V 300pF 4nC@4.5V 5.5A 80pF SOT-23 MOSFETs ROHSTECH PUBLICMOSFETsFDN340P
SOT-23-55℃~+150℃ 1 P-Channel 1.5V 121pF 20V 2A 500mW 56pF 7.2nC@4.5V 70mΩ@4.5V 779pF P-Channel SOT-23 MOSFETs ROHSonsemiMOSFETs
Parts
77| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | CC0805KKX7R6BB105 | Vault:FP-CC0805-0_85-MFG | C1, C2, C3, C4, C5, C6, C7, C8, DC1, DC2, DC3, DC4, DC5, DC6, DC7, DC8 |
| 15 | , , , , , , , , , , , , , , | ||
| 15 | CRCW08050000Z0EA | Vault:RESC2013X50X30LL20T20 | R1, R2, R3, R4, R5, R6, R9, R10, R14, R15, R16, R17, R18, R19, R20 |
| 8 | B3B-XH-A(LF)(SN) | Vault:FP-B3B-XH-A_LF_SN-MFG | J1_JSTBreakout1, J1_JSTBreakout2, J1_JSTBreakout3, J1_JSTBreakout4, J1_JSTBreakout5, J1_JSTBreakout6, J1_JSTBreakout7, J1_JSTBreakout8 |
| 3 | 150080SS75000 | Vault:0805_A | LED1, LED2, LED3 |
| 3 | CAT16-103J4LF | Vault:BOUR-CAT16-103J4LF_L | R7, R8, R13 |
| 2 | Header 4X2 | Miscellaneous Connectors.IntLib:HDR2X4 | P2, P3 |
| 2 | Header 6X2 | Miscellaneous Connectors.IntLib:HDR2X6 | ESPSPI, TNYSPI |
| 2 | MMBT2222ALT1G | Vault:ONSC-SOT-23-3-318-08_V | Q1, Q2 |
| 1 | AP2112K-3.3TRG1 | Vault:FP-SOT25-IPC_A | U4 |
| 1 | CP2104-F03-GM | Vault:SLAB-QFN-24-2675x2675TP_M | U5 |
| 1 | ESP32-WROVER-B_(16MB) | Vault:XCVR_ESP32-WROVER-B_(16MB) | U1 |
| 1 | FDN339AN | Vault:FP-527AG-MFG | Q3 |
| 1 | FDN340P | Vault:FP-527AG-MFG | Q4 |
| 1 | FSMSMTR | Vault:TECO-FSMSMTR_V | SW1 |
| 1 | Header 16X2 | Miscellaneous Connectors.IntLib:HDR2X16 | GPIO |
| 1 | Header 2 | Miscellaneous Connectors.IntLib:HDR1X2 | P6 |
| 1 | SN74HCT245DWR | Vault:FP-DW0020A-MFG | U6 |
| 1 | Teensy 4.0 | Vault:MODULE_DEV-15583 | U2 |
| 1 | XT30-F | Vault:XT30-F-Footprint-1 | J2 |
More from coelacant1/Protogen-Electronics
1Similar boards
- 4 layers59 × 101 mm
Enku mainboard r0.1
aliaksei-lameyka/ENKU-Base-reader
Open enku-mainboard-r0.1.kicadpro with KiCad10.0.7. Matching PCB/root schematic and power.kicadsch, mcuio.kicadsch, epdhv.kicadsch, connectors.kicadsch are canonical.
127 parts1CERN-OHL-W-2.0 - 4 layers160 × 100 mm
K30p VME
transistorfet/retroverse
A collection of VME-based hardware and software for modular computers
133 parts17 - 2 layers368.3 × 254 mm
- 2 layers150 × 195 mm
SCB
Stogalosu/Smart-Chess-Board
A smart chess board that connects to your phone and automatically makes moves
52 parts1 - 2 layers259.8 × 300 mm
- 2 layers50 × 50 mm
- 4 layers94.5 × 80.5 mm
ReboostV2.1 fixed
fl4p/dcdc-parasitics
KiCad → FastHenry extractor for half-bridge power-stage parasitics (commutation-loop L, common-source inductance, gate-loop L/R) → SPICE subckt + SVG schematic
184 parts - 2 layers135.1 × 159.4 mm
Questions
How big is the ProtogenControllerV1 PCB?
It measures 65 × 52 mm and has 4 copper layers, 1.6 mm thick.
What parts does the ProtogenControllerV1 use?
77 parts, built around the SN74HCT245DWR(LX), CP2104-F03-GM, AP2112K-3.3TRG1 and CC0805KKX7R6BB105. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ProtogenControllerV1 KiCad files?
From the coelacant1/Protogen-Electronics repository on GitHub, at the commit this page was made from: the board is ProtogenControllerV1/ProtogenControllerV1/ProtogenControllerV1.kicad_pcb and its schematic ProtogenControllerV1/ProtogenControllerV1/JSTBreakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ProtogenControllerV1 design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).