2 layers90.2 × 99.1 mm
Control logic
codemonkey76/DIY-8-Bit-Computer
DIY 8-Bit Computer, based on the design by Ben Eater
94 parts
2 layers90.2 × 88.9 mm
DIY 8-Bit Computer, based on the design by Ben Eater
- Size
- 90.2 × 88.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 70
- Nets
- 72
- Pads
- 234
- Tracks, vias
- 1,078, 144
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 25 Aug 2019
- Updated
- 25 Aug 2019
Overview
Alu is an open-source printed circuit board by codemonkey76, from the codemonkey76/DIY-8-Bit-Computer repository on GitHub. It is a 2-layer board of 90.2 × 88.9 mm with 70 parts on 72 nets, routed with 1,078 tracks and 144 vias.
It is built around the 74LS245SC, 74LS86 and 74LS02PC, with the 74LS173SC, A1 and A2 among its other parts. Its parts include 10 resistors, 10 diodes, 8 ICs and 5 connectors. It belongs with the retro computing and games boards of this library.
Main components
1274LS245SC
-0℃~+70℃ 12ns@5V,45pF 15mA 24mA 4.75V~5.25V 74LS 8 Bidirectional Output enable Schmitt trigger Tri-State - Buffers, Drivers, Receivers, Transceivers ROHSTexas InstrumentsBuffers, Drivers, Receivers, Transceivers
74LS86
DIP-14-20℃~+75℃ 10mA 2.7V 23ns@5V,15pF 2V 400mV 400uA 5V 74LS 800mV 8mA XOR Gate DIP-14 Logic Gates ROHSHITLogic Gates74LS02PC
DIP-140℃~+70℃ 15ns@5V,15pF 2 2.7V 2V 4 4.75V~5.25V 400uA 500mV 74LS 800mV 8mA 8mA NOR Gate DIP-14 Logic Gates ROHSonsemiLogic Gates74LS173SC
CDIP-160℃~+70℃ 10ns 10ns 28mA 30MHz 4 4.75V~5.25V 40ns@5V,15pF 74LS Series Asynchronous D-Type Reset Rising Edge Tri-State CDIP-16 Flip FlopsTexas InstrumentsFlip Flops
A1
SOD-123FLDiodes - General PurposeWild GooseA2
SOD-123FL-55℃~+150℃ 1 Independent 1.1V@1A 100V 1A 30A 50uA SOD-123FL Diodes - General Purpose ROHSZhengxinDiodes - General PurposeA3
SOD-123FL-55℃~+150℃ 1 Independent 1.1V@1A 1A 200V 30A 50uA SOD-123FL Diodes - General Purpose ROHSZhengxinDiodes - General PurposeA4
SOD-123FL-55℃~+150℃ 1 Independent 1.1V@1A 1A 30A 400V 5uA SOD-123FL Diodes - General Purpose ROHSZhengxinDiodes - General PurposeA5
SOD-123FL-65℃~+150℃ 1 Independent 1.1V@1A 25A 600V 800mA SOD-123FL Diodes - General Purpose ROHSDDFDiodes - General Purpose
A6
SOT89-3-20℃~+85℃@(Ta) 1 1.8uA 5V 60V 70dB@(1kHz) 70mV@(10mA) Fixed Over Temperature Protection、Enable、Short Circuit Protection Positive SOT89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSeaward ElecVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsA7
SOD-123FL1.1V@1A 1A 1kV 25A 5uA@1kV Independent SOD-123FL Diodes - General Purpose ROHSGOODWORKDiodes - General Purpose
B0
插件,D2.5xL9mmThermal Fuses (TCO)SETsafe | SETfuse
README
README.mdDIY-8-Bit-Computer
Based off schematics and design of breadboard computer by Ben Eater, available in kit form at: https://eater.net/8bit/kits
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 220R | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1, R2, R3, R4, R5, R6, R7, R8, R9, R10 |
| 2 | 74LS283 | Package_DIP:DIP-16_W7.62mm_Socket | U5, U6 |
| 2 | 74LS86 | Package_DIP:DIP-14_W7.62mm_Socket | U7, U8 |
| 1 | +5V | TestPoint:TestPoint_Pad_1.5x1.5mm | TP14 |
| 1 | 74LS02 | Package_DIP:DIP-14_W7.62mm_Socket | U3 |
| 1 | 74LS08 | Package_DIP:DIP-14_W7.62mm_Socket | U1 |
| 1 | 74LS173 | Package_DIP:DIP-16_W7.62mm_Socket | U2 |
| 1 | 74LS245 | Package_DIP:DIP-20_W7.62mm_Socket | U4 |
| 1 | A Register | Connector_JST:JST_PH_S8B-PH-K_1x08_P2.00mm_Horizontal | J4 |
| 1 | A_0 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP16 |
| 1 | A_1 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP17 |
| 1 | A_2 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP18 |
| 1 | A_3 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP20 |
| 1 | A_4 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP22 |
| 1 | A_5 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP24 |
| 1 | A_6 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP27 |
| 1 | A_7 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP29 |
| 1 | B Register | Connector_JST:JST_PH_S8B-PH-K_1x08_P2.00mm_Horizontal | J5 |
| 1 | BUS_0 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP6 |
| 1 | BUS_1 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP7 |
| 1 | BUS_2 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP8 |
| 1 | BUS_3 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP9 |
| 1 | BUS_4 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP10 |
| 1 | BUS_5 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP11 |
| 1 | BUS_6 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP12 |
| 1 | BUS_7 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP13 |
| 1 | B_0 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP19 |
| 1 | B_1 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP21 |
| 1 | B_2 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP23 |
| 1 | B_3 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP26 |
| 1 | B_4 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP28 |
| 1 | B_5 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP30 |
| 1 | B_6 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP31 |
| 1 | B_7 | TestPoint:TestPoint_Pad_1.5x1.5mm | TP32 |
| 1 | Bus | Connector_JST:JST_PH_S8B-PH-K_1x08_P2.00mm_Horizontal | J1 |
| 1 | CF | TestPoint:TestPoint_Pad_1.5x1.5mm | TP1 |
| 1 | CF | LED_THT:LED_D5.0mm | D1 |
| 1 | CLK | TestPoint:TestPoint_Pad_1.5x1.5mm | TP4 |
| 1 | CLR | TestPoint:TestPoint_Pad_1.5x1.5mm | TP5 |
| 1 | GND | TestPoint:TestPoint_Pad_1.5x1.5mm | TP15 |
| 1 | Misc | Connector_JST:JST_PH_S7B-PH-K_1x07_P2.00mm_Horizontal | J3 |
| 1 | Power | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J2 |
| 1 | S0 | LED_THT:LED_D5.0mm | D3 |
| 1 | S1 | LED_THT:LED_D5.0mm | D4 |
| 1 | S2 | LED_THT:LED_D5.0mm | D5 |
| 1 | S3 | LED_THT:LED_D5.0mm | D6 |
| 1 | S4 | LED_THT:LED_D5.0mm | D7 |
| 1 | S5 | LED_THT:LED_D5.0mm | D8 |
| 1 | S6 | LED_THT:LED_D5.0mm | D9 |
| 1 | S7 | LED_THT:LED_D5.0mm | D10 |
| 1 | SU | TestPoint:TestPoint_Pad_1.5x1.5mm | TP25 |
| 1 | ZF | TestPoint:TestPoint_Pad_1.5x1.5mm | TP2 |
| 1 | ZF | LED_THT:LED_D5.0mm | D2 |
| 1 | ~EO~ | TestPoint:TestPoint_Pad_1.5x1.5mm | TP33 |
| 1 | ~FI~ | TestPoint:TestPoint_Pad_1.5x1.5mm | TP3 |
The 66 most common of 70 parts.
Questions
How big is the Alu PCB?
It measures 90.2 × 88.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Alu use?
70 parts, built around the 74LS245SC, 74LS86, 74LS02PC and 74LS173SC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Alu KiCad files?
From the codemonkey76/DIY-8-Bit-Computer repository on GitHub, at the commit this page was made from: the board is ALU/alu.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Alu design in my own project?
Its repository states no licence, so its author keeps all rights: ask codemonkey76 before reusing the design.
More from codemonkey76/DIY-8-Bit-Computer
10- 2 layers95.3 × 81.3 mm
- 2 layers78.7 × 58.4 mm
Register a
codemonkey76/DIY-8-Bit-Computer
DIY 8-Bit Computer, based on the design by Ben Eater
50 parts - 2 layers78.7 × 58.4 mm
Register b
codemonkey76/DIY-8-Bit-Computer
DIY 8-Bit Computer, based on the design by Ben Eater
50 parts - 2 layers78.7 × 58.4 mm
Instruction register
codemonkey76/DIY-8-Bit-Computer
DIY 8-Bit Computer, based on the design by Ben Eater
46 parts - 2 layers72.4 × 63.5 mm
- 2 layers72.4 × 50.8 mm
Address register
codemonkey76/DIY-8-Bit-Computer
DIY 8-Bit Computer, based on the design by Ben Eater
39 parts - 2 layers72.4 × 74.9 mm
Output register
codemonkey76/DIY-8-Bit-Computer
DIY 8-Bit Computer, based on the design by Ben Eater
35 parts - 2 layers63.5 × 45.7 mm
Program counter
codemonkey76/DIY-8-Bit-Computer
DIY 8-Bit Computer, based on the design by Ben Eater
29 parts - 2 layers80 × 93.2 mm
Similar boards
- 2 layers300 × 300 mm
SAP Extended
cyrillvalentini/SAP-Extended
Extended Simple-As-Possible Computer based on Ben Eaters video series
440 parts1 - 2 layers100 × 99.9 mm
- 2 layers67.8 × 55 mm
- 2 layers
- 2 layers61.8 × 73.2 mm
- 2 layers47.3 × 52.8 mm
- 2 layers74.3 × 52.8 mm
- 2 layers141 × 88 mm
ErgoSNM Keyboard Right Prototype 1
siderakb/ergo-snm-keyboard
ErgoSNM is a split ergonomic keyboard integrated with trackball, wireless is in beta
70 parts172CERN-OHL-P-2.0